JTB00281NAS1

Page 1 of 8
TECHNICAL BULLETIN
JTB00281NAS1
07 FEB 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 501-17
Roof Opening Panel Frame Corrosion
AFFECTED VEHICLE RANGE:
XJ Range (X351)
Model Year:
2010-2012
VIN:
V00047-V37494
MARKETS:
NAS
CONDITION SUMMARY:
Situation: Corrosion on the roof opening panel frame, which can be seen when the roof opening panel is open,
may be evident.
Cause: This may be caused by insufficient thickness of coating on the frame.
Action: In the event of a customer concern of the above, refer to the Repair Procedure outlined below.
PARTS:
NOTE: Consumable cost of $23.50 to be claimed as 'ZZZ001'.
C2D30282
Protection Tape kit
Quantity: 1
WARRANTY:
NOTE: Consumable cost of $23.50 to be claimed as 'ZZZ001'.
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Roof Opening Panel Frame Corrosion
Prevention
76.96.09
2.60
F25
C2D5725
NOTE: Normal Warranty policies and procedures apply.
REPAIR PROCEDURE:
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 2 of 8
NOTE: This repair Procedure must be carried out on both sides of the roof opening panel.
1. Remove the roof opening panel (TOPIx Workshop Manual section 501-17: Roof Opening Panel).
2.
NOTE: Make sure no damage is caused to
the rubber seal; do not twist or bend the
seal.
Using a suitable tool, remove the seal from the
edge of the roof opening panel.
3.
NOTE: Make sure no damage is caused to
the rubber seal.
Move the rubber seal aside, allowing access to the
corroded area.
4.
NOTE: Example of the corrosion area.
When the rubber seal has been moved aside, the
corroded area can been seen.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 3 of 8
5. Using a suitable de-greasing agent, de-grease the
area to be worked on.
6.
NOTE: Mask off the roof opening panel
aperture and the surrounding area to make
sure no dirt or dust will ingress into the
vehicle.
Using a suitable tape, mask the rubber seals off to
protect from damage.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 4 of 8
7. Using a suitable air line, make sure the area is dry
and free from dirt and grease.
8. Using 120 - 360 grit sandpaper, sand the corroded
area(s) down by hand.
9. Using a suitable air line, make sure the area is dry
and free from dirt and dust.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 5 of 8
10. Prepare surrounding area for painting.
11. Using a suitable rust converter agent, treat the corroded area completely and allow to dry thoroughly.
12. Using a suitable de-greaser, clean the area.
13. Using a suitable soft-edge masking, mask the are
shown and mask off the rest of the surrounding
vehicle.
14. Using a suitable aerosol primer, prime the
affected areas and allow to dry completely.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 6 of 8
15.
NOTE: Allow each coat of paint to dry
completely before applying the next coat of
paint.
When the aerosol primer has dried completely, use
U-POL UP0801 satin Black (or equivalent), apply
three (3) coats of paint on each side of the roof
opening panel being repaired.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 7 of 8
16.
WARNING: Make sure no damage is
caused to the vehicle or tape using the hot
air gun.
NOTE: Using a suitable hot air gun will
help with fitting the textured tape to ensure
no creases are made to the textured tape.
When the paint has dried completely, apply the
textured tape to the affected area.

 Apply the textured tape to both sides of the
vehicle, ensuring it is fitted correctly with no
creases or damage.
17. Make sure the textured tape is fitted correctly
under both fixed glass panels.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013
Page 8 of 8
18. Refit the rubber seals.
19. Install the roof opening panel (TOPIx Workshop Manual section 501-17: Roof Opening Panel).

 Verify roof opening panel operation.
http://topix.jaguar.jlrint.com/topix/service/document/231942
2/13/2013