JTB00280NAS1

TECHNICAL BULLETIN
JTB00280NAS1
12-DEC-12
SECTION: 501-12
Front Overhead Console Lamps do not Operate as Expected
AFFECTED VEHICLE RANGE:
XF (X250)
VIN:
Model Year:
R00019-S34279
2009-2012
CONDITION SUMMARY:
Situation: The front overhead console lamps may not operate as expected.
Cause: This may be caused by issues within the printed circuit board (PCB) in the lamp assembly.
Action: In the event of a customer concern of the above, refer to the Repair Procedure outlined below.
PARTS:
C2Z25623 ................ PCB Kit A
Qty: 1
TOOLS:
Refer to Workshop Manual / Repair Procedure for any required special tools
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair
time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a
quantity of zero.
SRO
DESCRIPTION
Roof console circuit board - Renew
TIME
(HOURS)
86.94.67
0.20
CONDITION
CODE
42
CAUSAL
PART
C2Z12623
Normal Warranty policies and procedures apply
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and
equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not
a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to determine whether
this bulletin applies to a specific vehicle.
© Jaguar Land Rover North America, LLC
555 MacArthur Boulevard
Mahwah, NJ 07430
REPAIR PROCEDURE
1. Refer to Workshop Manual section 501-12 (steps 1 and 2
only) and remove the front overhead console lamp assembly.
2.
WARNING: The pink bubble wrap that is used for
packaging may be used as a work mat.
NOTE: Make sure no damage is caused when
removing the electrical connectors.
Disconnect the two electrical connectors.
3.
NOTE: Some items removed for clarity.
Move aside the black plastic cover.
4.
NOTE: Make sure no damage is caused when unclipping the small printed circuit boards.
Using a suitable tool, un-clip the three small printed circuit
boards.
5.
NOTE: Make sure no damage is caused when unclipping the electrical connector.
Using a suitable tool un-clip the electrical connector.
•
Release the two securing clips.
6.
NOTE: Make sure no damage is caused when
removing the printed circuit board.
Remove the main circuit board.
7.
NOTE: Make sure all the grease is removed from the
electrical connectors.
Using a suitable clean cloth remove the grease on the three
electrical connectors.
•
Using the wipe supplied in the kit make sure all the
grease is removed from the electrical connectors.
8.
CAUTION: When installing the rubber sleeves it is
important not to damage or split them.
NOTE: Install all three sleeves from the top.
Install the three rubber sleeves to the electrical connectors.
•
The rubber sleeves must be approximately 2-3mm
from the bottom of the electrical connector.
9.
CAUTION: Prior to touching the new printed circuit
boards it is advised that your hands are clean and you
have earthed your body out by touching the steel work
bench.
Change over the three interior light bulbs from the old printed
circuit board to the new printed circuit board.
10.
NOTE: Make sure no damage is caused when
installing the new printed circuit board.
NOTE: Locate the printed circuit boards into the four
locating fixings before clipping the printed circuit board
into position.
Install the new printed circuit board.
11.
NOTE: Make sure no damage is caused when
installing the three small printed circuit boards.
Install the three small printed circuit boards.
12.
NOTE: Make sure the electrical ribbon is square in
the connector, before it is fully engaged.
NOTE: Make sure no damage is caused when
installing the electrical connectors.
Connect the electrical connector.
• Push in the two securing clips.
13. Install the black plastic cover.
14.
NOTE: Make sure no damage is caused when
installing the electrical connectors.
Connect the two electrical connectors.
15. Refer to Workshop Manual section 501-12 (steps 2 and 1
only) and install the front overhead console lamp assembly.
16. Verify front overhead console lamp operation.