JTB00376NAS1

Page 1 of 4
TECHNICAL BULLETIN
JTB00376NAS1
25 SEP 2014
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to do the job
properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service.
The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 501-05
Parcel Shelf Separation
AFFECTED VEHICLE RANGE:
F-TYPE (X152)
Model Year:
VIN:
2015
K07480-K17736
Body style:
Coupe
MARKETS:
NAS
CONDITION SUMMARY:
Situation: The noise, vibration, and harshness (NVH) pad installed to the underside of the parcel shelf may become detached.
Cause: This may be caused by poor adhesion of the double-sided tape.
Action: Should a customer express this concern, follow the Service Instruction outlined below.
PARTS:
NOTE: An allowance equivalent to £1.50 has been allocated for the cost of the locally sourced high-strength glue and must be
claimed using 'ZZZ001'.
-
High-strength glue
Quantity: Locally sourced
TOOLS:
Refer to Workshop Manual for any required special tools.
WARRANTY:
NOTE: An allowance equivalent to £1.50 has been allocated for the cost of the locally sourced high-strength glue and must be
claimed using 'ZZZ001'.
NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be
taken as guidance only. Always refer to TOPIx to obtain the latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of
zero.
DESCRIPTION
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
Parcel shelf - Repair
05.10.30
0.30
7
T2R15962PVJ
NOTE: Normal Warranty policies and procedures apply.
SERVICE INSTRUCTION:
NOTE: This procedure requires a hot melt glue gun and a high-strength glue (to be sourced locally).
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
NOTE: Some components are shown removed for clarity.
1. Open the luggage compartment lid.
2. Remove the parcel shelf.
http://topix.jaguar.jlrint.com/topix/service/document/498561
9/30/2014
Page 2 of 4
3. Remove the noise, vibration, and harshness (NVH) pad from the underside of the
parcel shelf.
4. Remove and discard the self-adhesive tape from the underside of the parcel shelf.
http://topix.jaguar.jlrint.com/topix/service/document/498561
9/30/2014
Page 3 of 4
5.
CAUTION:
Use care when
working with hot
glue.
CAUTION:
Make sure when
bonding is
complete, the
glue
manufacturer's
curing guidelines
are followed.
Failure to do so
may lead to the
NVH pad
separating from
the parcel shelf in
the future.
Using a hot melt
glue gun, bond the
NVH pad to the
parcel shelf.

 Apply a
sufficient
amount of glue
shown.

 Install the NVH
pad in stages
(one row at a
time).
• Press
down
firmly on
the NVH
pad and
allow the
hot melt
glue to
cure
before
proceeding
to the
next row.
http://topix.jaguar.jlrint.com/topix/service/document/498561
9/30/2014
Page 4 of 4
6. After allowing the glue to dry, install the parcel shelf.
7. Close the luggage compartment lid.
http://topix.jaguar.jlrint.com/topix/service/document/498561
9/30/2014