5NP-A4B3R-01

@) HYUnDRI I
GROUP
nEWTHlnKlnG.
nEW POSSIBILITIES.
Technical Service Bulletin
SUBJECT:
NUMBER
16-01-070
CAMPAIGN
DATE
MODEL(S)
DECEMBER 2016
VELOSTER (FS)
MANUAL HEATER CONTROL UNIT
REPLACEMENT (SERVICE CAMPAIGN TY6)
This TSB supersedes TSB 15-01-042 to include 2015 model year for the Applicable Vehicles.
*IMPORTANT
*** Retail Vehicles Only ***
Dealers must perform this Service Campaign whenever an affected vehicle is in the shop for any
maintenance or repair.
When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty
Vehicle Information" screen via WEBDCS to identify open Campaigns.
Description: On some VELOSTER (FS) vehicles equipped with the manual heater control unit, the
internal switch for the blower (fan) speed control may become inoperative.
Follow the procedure outlined in this bulletin to replace the heater control unit.
Applicable Vehicles:
• Certain 2014-2015 MY Veloster (FS) equipped with manual heater (HVAC) control unit
Parts Information:
Part Name
Previous
New
Part Front View
97250-2V0114PD
Manual Heater
Control Unit
(Matte Black Panel /
Dark Gray Fan Knob)
97250-2V0114PDQH
97250-2V0114X
(Matte Black Panel /
Light Gray Fan Knob)
97250-2V0114XQH
97250-2V011 BLH
(Red box area above
shows the general
location at the back
of the unit where the
P/N can be found.)
(Gloss Black Panel/
Light Gray Fan Knob)
97250-2V011 BLHQH
97250-2V011 BPD
(Gloss Black Panel/
Dark Gray Fan Knob)
97250-2V011 BPDQH
Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair
SUBJECT:
MANUAL HEATER CONTROL UNIT REPLACEMENT (SERVICE CAMPAIGN TY6)
SST Information:
Description
Tool Part#
Panel Puller
PANELPULLER
- - - - - -~
Tool View
,--
NOTE: One (1) tool has been automatically sent to every dealer to perform this service campaign.
Additional tools can be ordered through the PDC.
Warranty Information:
MANUAL HEATER CONTROL UNIT REPLACEMENT
NOTE: Submit Claim on Campaign Claim Entry Screen
Service Procedure:
1. Turn the ignition to OFF.
2. Release the center fascia panel mounting clips
(A) in the following steps using the puller tool.
A.CAUTION
Wear eye protection goggles to prevent
possible injury during the following steps.
3. Insert the hook end of the puller tool (B)
positioned into the air vent hole as shown for the
removal process.
TSB #: 16-01-070
Page 2 of 4
SUBJECT:
MANUAL HEATER CONTROL UNIT REPLACEMENT (SERVICE CAMPAIGN TY6)
4. Securely position the puller tool to the upper
right corner of the LH Center Vent and release
the clips with a firm pull.
---------~
5. Securely position the puller tool to the upper
left corner of the RH Center Vent and release
the clips with a firm pull.
Use one hand to stabilize the hook end of the tool against the recessed portion of the
center vent inner lip while pulling. This will help prevent slipping and scratching the
center fascia panel near the vent. Firmly tug the T-handle of the tool to release clips.
6. Once the holding clips are released, carefully
separate the center fascia panel (C) to access
the rear connectors.
TSB #: 16-01-070
Page 3 of 4
SUBJECT:
MANUAL HEATER CONTROL UNIT REPLACEMENT (SERVICE CAMPAIGN TY6)
7. Disconnect the connectors (D) as shown.
8. Loosen the manual heater control unit
mounting screws (E).
9. Remove the old heater control unit (F) from the
center fascia panel and replace it with the new
heater control unit.
Red box area on
the right shows the
general location at
the back of the unit
where the P/N can
be found.
10. Reinstall all the removed parts in the reverse order of removal.
11. Verify repair.
• Check operation of all panel switches.
• Check operation of the heater control unit.
TSB #: 16-01-070
Page 4 of 4