PI1358B
Service Bulletin Details
Public Details for: PI1358B
This preliminary informational bulletin provides a procedure to install retainers to the carpet to correct a condition of the carpet pulling loose from under driver side body hinge pillar trim panel .
- 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 -
Models from 2017
2017 CHEVROLET EQUINOX |
2017 GMC TERRAIN |
Models from 2016
2016 CHEVROLET EQUINOX |
2016 GMC TERRAIN |
Models from 2015
2015 CHEVROLET EQUINOX |
2015 GMC TERRAIN |
Models from 2014
2014 CHEVROLET EQUINOX |
2014 GMC TERRAIN |
Models from 2013
2013 CHEVROLET EQUINOX |
2013 GMC TERRAIN |
Models from 2012
2012 CHEVROLET EQUINOX |
2012 GMC TERRAIN |
Models from 2011
2011 CHEVROLET EQUINOX |
2011 GMC TERRAIN |
Models from 2010
2010 CHEVROLET EQUINOX |
2010 GMC TERRAIN |
Bulletin No.: PI1358B Date: 16-Jun-2016 Subject: Carpet Pulls Loose from Under Driver Side Body Hinge Pillar Trim Panel Models: 2010-2017 Chevrolet Equinox 2010-2017 GMC Terrain Attention: This PI also applies to any of the above models that may be Export from North America vehicles. This PI has been revised to add the 2017 Model Year. Please discard PI1358A. Condition/Concern Some customers may comment that the driver side carpet pulls away from the lower left body hinge pillar trim panel (kick panel). Recommendation/Instructions Technicians should remove the lower left body hinge pillar trim panel (kick panel) and install push pins to the area shown following the steps below: 1 1. Remove the body hinge pillar trim panel. 2. Pull back the carpet to expose the driver footrest. 3. Remove the two mounting nuts and remove the footrest. 2 4. With the footrest on a bench, turn over and mark the first and fourth “box” of the center row with a paint pen as shown. 5. Using a 1/4” (6.35 mm) drill bit, drill two holes in the center of the marks. 6. Install the footrest and the two mounting nuts. 3 7. Place two rivets in the holes drilled and pull the carpet gently over the rivets. 8. Push the carpet over the rivets and punch through the carpet as shown. 4 9. Lift the carpet back up, remove the rivets and use a punch to open the holes of the carpet to allow push pins through. 10. Install the push pins through each hole. Note: Trimming the jute around the push pins helps with installation. 5 11. Install the carpet to the driver footrest using the push pins. 12. Install the body hinge pillar trim panel. Parts Information Part Number Description Quantity 11569663 Rivet 2 22718305 Push Pin 2 Warranty Information For vehicles repaired under warranty, use: Labor Operation Description Labor Time 1080198* Install Retainers to Retain Carpet 0.5 hr *This is a unique Labor Operation for Bulletin use only. It will not be published in the Labor Time Guide. GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION 6 Bulletin No.: Pl1358B Date: 16-Jun-2016 Service Bullet,in Subject: Carpet Pulls Loose from Under Driver Side Body Hinge Pillar Trim Panel Models: 2010-2017 Chevrolet Equinox 2010-2017 GMC Terrain Attention: This Pl also applies to any of the above models that may be Export from North America vehicles. This Pl has been revised to add the 2017 Model Year. Please discard P/1358A. Condition/Concern Some customers may comment that the driver side carpet pulls away from the lower left body hinge pillar trim panel (kick panel). Recommendation/Instructions Technicians should remove the lower left body hinge pillar trim panel (kick panel) and install push pins to the area shown following the steps below: 1. Remove the body hinge pillar trim panel. 2. Pull back the carpet to expose the driver footrest. 3. Remove the two mounting nuts and remove the footrest. 2 4. With the footrest on a bench, turn over and mark the first and fourth "box" of the center row with a paint pen as shown. 5. Using a 1/4" (6.35 mm) drill bit, drill two holes in the center of the marks . 6. Install the footrest and the two mounting nuts. 3 7. Place two rivets in the holes drilled and pull the carpet gently over the rivets. 8. Push the carpet over the rivets and punch through the carpet as shown. 4 9. Lift the carpet back up, remove the rivets and use a punch to open the holes of the carpet to allow push pins through. 10. Install the push pins through each hole. Note: Trimming the jute around the push pins helps with installation . 5 11. Install the carpet to the driver footrest using the push pins. 12. Install the body hinge pillar trim panel. Parts Information Part Number Description Quantity 11569663 Rivet 2 22718305 Push Pin 2 Warranty Information For vehicles repaired under warranty, use: Labor Operation Description Labor Time 1080198* Install Retainers to Retain Carpet 0.5 hr *This is a unique Labor Operation for Bulletin use only. It will not be published in the Labor Time Guide. GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer" . They are written to inform these technicians of conditions that may occur on some vehicles , or to provide information that could assist in the proper service of a vehicle . Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described , DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition . See your GM dealer for information on whether your vehicle may benefit from the information . • WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION 6