JTB00499NAS2

Page 1 of 13
TECHNICAL BULLETIN
JTB00499NAS2
29 SEP 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and
equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you
are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to
determine whether this bulletin applies to a specific vehicle.
This reissue replaces all previous versions. Please destroy all previous versions.
Changes are highlighted in gray
SECTION: 204-02
'Creak' Noise From Rear Suspension
AFFECTED VEHICLE RANGE:
F-PACE (X761)
Model Year:
VIN:
Assembly
Plant:
2017
045409-075852
Solihull
MARKETS:
NAS
CONDITION SUMMARY:
Situation: A 'creak noise' may be evident from the rear of the vehicle while driving.
Cause: This may be caused by deflection of the rear spring top mount isolator, allowing the spring to contact the
vehicle body.
Action: Should a customer express this concern, see the Service Instruction outlined below.
PARTS:
NOTE: Parts are no longer on restriction.
C2Z2224
Wishbone nut
2
T2H2202
Damper bottom bolt
2
T2H3176
Lower wishbone nut
2
T2H3507
Damper bottom nut
2
T2H3774
Lower wishbone bolt
2
T2H16285
Wishbone bolt
2
T4A1994
Lower Isolator
2
T4A2003
Upper Isolator
2
XR848057
ARB drop link nut
2
TOOLS:
Refer to Workshop Manual for any required special tools.
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change; those
quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 2 of 13
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
Rear spring isolator - Set
64.20.02.99
0.7
GW2
T4A2008
NOTE: Normal Warranty procedures apply.
NEW COMPONENT OVERVIEW
1. Lower and upper isolators.
• A = Lower Isolator - T4A1994.
• B = Upper Isolator - T4A2003.
SERVICE INSTRUCTION:
CAUTION: Nuts and bolts must be tightened with vehicle at normal ride height.
1.
CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Remove the rear left wheel.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 3 of 13
3. Install a suitable transmission jack and compress the rear
left suspension.
4. Install suitable coil spring compressors.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 4 of 13
5. Remove and discard the stabilizer bar link nut.
6. Remove and discard the rear shock absorber nut and
bolt.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 5 of 13
7. Remove and discard the rear tie-rod outer nut and bolt.
8. Remove and discard the rear lower arm nut and bolt.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 6 of 13
9. Note the orientation of the coil spring isolator on the rear
lower arm.
10. Lower the transmission jack to allow the rear lower arm to articulate (1) as shown and remove (2) the rear coil
spring.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 7 of 13
11. Remove and discard the upper and lower coil spring isolators.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 8 of 13
12.
CAUTION: Make sure the upper and lower coil spring isolators are fitted in the correct orientation.
Install the new upper and lower coil spring isolators.
13.
WARNING: Make sure the rear coil spring is correctly located.
Install (1) the rear coil spring and use the transmission jack to support and raise (2) the rear lower arm.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 9 of 13
14.
WARNING: Make sure the rear coil spring is
correctly located.
Make sure the lower rear coil spring isolator is engaged
correctly on the rear lower arm.
15. Install a new lower rear arm nut and bolt.
• Stage one - Torque: 110 Nm
• Stage two - Torque: 60°
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 10 of 13
16. Install a new tie-rod nut and bolt.
• Stage one - Torque: 60 Nm
• Stage two - Torque: 60°
17. Install a new rear shock absorber nut and bolt.
• Torque: 170 Nm
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 11 of 13
18. Install a new stabilizer bar link nut.
• Stage one - Torque: 40 Nm
• Stage two - Torque: 45°
19. Using the transmission jack, raise the rear suspension.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 12 of 13
20. Remove the coil spring compressors.
21. Lower and remove the transmission jack.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016
Page 13 of 13
22.
WARNING: Apply a small amount of grease to
the bore and spigot areas of the wheel before
installation. Make sure the grease does not come
into contact with the braking components and the
wheel stud threads. Failure to follow these
instructions may result in personal injury.
Install the rear left wheel.
• Stage one - Torque: 4 Nm
• Stage two - Torque: 70 Nm
• Stage three - Torque: 133 Nm
23. Perform Steps 2-22 for the rear right suspension.
http://topix.jaguar.jlrext.com/topix/service/document/688023
10/4/2016