JTB00477NAS2

Page 1 of 4
TECHNICAL BULLETIN
JTB00477NAS2
06 OCT 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required
to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described
affects your vehicle. Contact an authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
This reissue replaces all previous versions. Please destroy all previous versions.
Changes are highlighted in gray
SECTION: 211-02
Rattle Noise From Front of Vehicle
AFFECTED VEHICLE RANGE:
XF (X260)
Model Year:
VIN:
Assembly
Plant:
2016-2017
Y00461-Y24769
Castle Bromwich
MARKETS:
NAS
CONDITION SUMMARY:
Situation: A rattle noise from the front of the vehicle may be evident when driving over rough roads (cobblestone, damaged roads,
etc.) when traveling at low to moderate speed (10-25mph / 16-40km/h).
Cause: This may be caused by bearing clearances in the steering rack, allowing a rattle noise to be created under specific drive cycles.
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
AJ811754
Steering rack bolts
4
AJ812516
Stabilizer bar bracket bolts
4
C2P9500
Shaft to gear bolt
1
T2H17786
Damper lower bolt
2
T2H19684
Steering Gear Left Hand Drive (LHD)
1
T2H3159
Lower Control arm nut
2
T2H3162
Subframe to body bolts
6
T2H5007
Lower control arm nuts
4
T2H6445
Lower wishbone to subframe nut
2
T4N3681
Lower control arm bolts
4
XR848057
Stabilizer bar to droplink nuts
2
TOOLS:
Jaguar Land Rover-approved Midtronics battery power supply
http://topix.jaguar.jlrext.com/topix/service/document/692867
10/31/2016
Page 2 of 4
Jaguar Land Rover-approved diagnostic tool with latest SDD software,
Calibration File
Refer to the Service Instruction/Workshop Manual for any required
special tools.
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here
must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a
quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Power steering gear - Renew - Ingenium I4 2.0L Diesel RWD
57.10.01
2.8
42
T2H9712
Power steering gear - Renew - Ingenium I4 2.0L Diesel AWD
57.10.01.57
3.9
42
T2H9712
Power steering gear - Renew - V6 3.0L S/C Petrol - RWD
57.10.01
2.9
42
T2H9712
Configure the power steering module
86.98.18
0.1
42
T2H9712
NOTE: Normal Warranty procedures apply.
SERVICE INSTRUCTION:
1. Typical
road
surface
that can
generate
the
rattle
sound.
http://topix.jaguar.jlrext.com/topix/service/document/692867
10/31/2016
Page 3 of 4
2. Typical
road
surface
that can
generate
the
rattle
sound.
3. Install a new steering gear (see TOPIx Workshop Manual section 211-02: Power Steering - Steering Gear).
4.
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the vehicle
battery during diagnosis / module programming.
CAUTION: Make sure all ignition ON/OFF requests are carried out; failure to perform these steps may cause
damage to control modules in the vehicle.
NOTE: The Jaguar Land Rover-approved diagnostic tool must be loaded with SDD146.08 v.248 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
5. Turn ignition ON (engine not running).
6. Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new session.
7. Follow the on-screen prompts, allowing the diagnostic tool to read the VIN, identify the vehicle, and initiating the data collect
sequence.
http://topix.jaguar.jlrext.com/topix/service/document/692867
10/31/2016
Page 4 of 4
8. Select Service functions from the Session Type screen.
9. Select continue.
10. Select the Recommendations tab.
11. Select Run to perform the Configure existing module - Power steering control module option.
12. Follow all on-screen instructions to complete this task, ensuring all Diagnostic Trouble Codes (DTC) are cleared.
13. When all tasks are complete, select the Session tab and then select the Close Session option.
14. Disconnect the diagnostic tool and battery power supply from the vehicle.
http://topix.jaguar.jlrext.com/topix/service/document/692867
10/31/2016