JTB00462NAS1

Service Bulletin Details

Public Details for: JTB00462NAS1

"situation: the rear seat release handle(s) may be loose or adrift. Cause: this may be due to the handle clip not being tightly retained"


- 2016 -

Models from 2016
2016 JAGUAR XF 
Page 1 of 4
TECHNICAL BULLETIN
JTB00462NAS1
22 DEC 2015
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 501-10
Rear Seat Release Handle Loose
AFFECTED VEHICLE RANGE:
XE (X760)
Model Year:
2017 Onwards
VIN:
900000 Onwards
Assembly Plant: Solihull
XF (X260)
Model Year:
2016 Onwards
VIN:
000001 Onwards
Assembly Plant: Castle Bromwich
MARKETS:
NAS
CONDITION SUMMARY:
Situation: The rear seat release handle(s) may be loose or adrift.
Cause: This may be due to the handle clip not being tightly retained.
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
T2H3762
Rubber Wiper Cap
Quantity: 2
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the
latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal
part number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Rear seat release lever rubber caps Install
76.71.58
0.1
42
T4N10148
NOTE: Normal Warranty procedures apply.
COMPONENT LOCATION
http://topix.jaguar.jlrext.com/topix/service/document/607422
1/7/2016
Page 2 of 4
1Component location.
SERVICE INSTRUCTION:
1Disconnect the rear left-hand seat release lever
from the parcel shelf.
2
NOTE: the rubber wiper cap must be
installed in the correct orientation.
Install the rubber wiper cap between the clipping
features on the rear seat release lever.
http://topix.jaguar.jlrext.com/topix/service/document/607422
1/7/2016
Page 3 of 4
3Connect the rear left-hand seat release lever to
the parcel shelf.
4Repeat steps 1-3 for the rear right-hand seat release lever.
5Check the operation of the rear right-hand seat
release cable at an angle of 20°.
http://topix.jaguar.jlrext.com/topix/service/document/607422
1/7/2016
Page 4 of 4
• Check that the rear seat release clip remains
fully engaged in the parcel shelf.
• Latch the rear seat into the lock position.
6Repeat step 5 to the rear left-hand seat release lever.
http://topix.jaguar.jlrext.com/topix/service/document/607422
1/7/2016

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.