LTB00767NAS1

Service Bulletin Details

Public Details for: LTB00767NAS1

"situation: the adaptive front lighting system (afs) warning lamp may be illuminated/flashing on the instrument cluster. Upon diagnosis, the technician may find diagnostic trouble codes (dtc) B1D64-87 and/or B1D65-87 stored in the headlamp


- 2014 - 2013 - 2012 - 2011 - 2010 -

Page 1 of 3
TECHNICAL BULLETIN
LTB00767NAS1
27 AUG 2015
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Land Rover service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 417-00
Adaptive Front Lighting System Warning Lamp Illuminated
AFFECTED VEHICLE RANGE:
LR4 (LA)
Model Year:
2010-2014
VIN:
513326-692053
Manufacturing Plant: Solihull
Range Rover (LG)
Model Year:
2013-2014
VIN:
001204-124982
Manufacturing Plant: Solihull
Range Rover Sport (LS)
Model Year:
2010-2013
VIN:
215623-814822
Manufacturing Plant: Solihull
Range Rover (LM)
Model Year:
2010-2012
VIN:
306630-393639
Manufacturing Plant: Solihull
MARKETS:
NAS
CONDITION SUMMARY:
Situation: The Adaptive Front lighting System (AFS) warning lamp may be illuminated/flashing on the
Instrument Cluster. Upon diagnosis, the technician may find Diagnostic Trouble Codes (DTC) B1D64-87 and/or
B1D65-87 stored in the headlamp leveling control module.
Cause: This may be caused by a software error within the headlamp leveling control module.
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
No Parts Required
TOOLS:
NOTE: this is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
SDD with latest DVD and Calibration File
http://topix.landrover.jlrint.com/topix/service/document/568672
8/27/2015
Page 2 of 3
Jaguar Land Rover-approved Midtronics battery power supply
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the
latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal
part number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Configure headlamp leveling module using
IDS/SDD
86.90.62
0.2
42
LR010521
NOTE: Normal Warranty procedures apply.
SERVICE INSTRUCTION:
CAUTION: a Jaguar Land Rover-approved Midtronics battery power supply must be connected to
the vehicle battery during SDD diagnosis / module programming.
CAUTION: ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
NOTE: SDD must be loaded with DVD142.03 v.212 or later.
1. Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
3. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
5. Select 'Diagnosis' from the Session Type screen.
6. Select the 'Selected Symptoms' tab, and then select:
• Electrical > Instruments > Warning lamps > Adaptive front lighting system lamp > Lamp illuminated
7. Select 'continue'.
8. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure existing module Headlamp control module' option.
9. Follow all on-screen instructions to complete this task, ensuring all DTCs are cleared.
http://topix.landrover.jlrint.com/topix/service/document/568672
8/27/2015
Page 3 of 3
10. If the fault code B1041-54 occurs after the configuration of the headlamp leveling control module,
perform the following.
• Select 'Service functions'.
• Run: Lighting - Headlamp control module system calibration
11. Exit the current session.
12. Disconnect the SDD and the battery power supply from the vehicle.
http://topix.landrover.jlrint.com/topix/service/document/568672
8/27/2015


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.