LTB00800NAS1

Page 1 of 3
TECHNICAL BULLETIN
LTB00800NAS1
11 AUG 2015
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Land Rover service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 303-00
Engine MIL Illuminated With DTCs P0116-21, P011B-22, P2183-00, or P2183
-22 Stored and Engine Coolant Heater Fitted
AFFECTED VEHICLE RANGE:
LR2 (LF)
Model Year:
2013-2015
VIN:
321215-439912
Manufacturing Plant: Halewood
Range Rover Evoque (LV)
Model Year:
2012-2013
VIN:
600000-856579
Manufacturing Plant: Halewood
MARKETS:
NAS
CONDITION SUMMARY:
Situation: Only on vehicles fitted with a Land Rover-approved Engine Coolant Heater (Block Heater), the
engine Malfunction Indicator Lamp (MIL) may be illuminated with Diagnostic Trouble Codes (DTC) P0116-21,
P011B-22, P2183-00, or P2183-22 stored in the Engine Control Module (ECM) and no hardware fault.
Cause: This may be caused by an On-board Diagnostics (OBD) calibration error.
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
No Parts Required
TOOLS:
NOTE: this is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.
SDD with latest DVD and Calibration File
Jaguar Land Rover-approved Midtronics battery power supply
WARRANTY:
NOTE: the 'Engine Control Module' (ECM) may also be referred to as 'Powertrain Control
Module' (PCM).
http://topix.landrover.jlrint.com/topix/service/document/564803
8/20/2015
Page 2 of 3
NOTE: Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the
latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal
part number with a quantity of zero.
DESCRIPTION
SRO
Configure existing module - Engine Control
12.90.13
Module
Powertrain control module adaption clear
18.90.27
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
0.2
04
LR028981
0.2
04
LR028981
NOTE: Normal Warranty procedures apply.
SERVICE INSTRUCTION:
CAUTION: a Jaguar Land Rover-approved Midtronics battery power supply must be connected to
the vehicle battery during SDD diagnosis / module programming.
CAUTION: ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
NOTE: SDD must be loaded with DVD142.03 v.212 or later.
1.
NOTE: check all hardware as per Diagnostic Trouble Code (DTC) index (see TOPIx Workshop
Manual, section 100-00 General Information - Diagnostic Trouble Code [DTC]) prior to
performing the software update.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
NOTE: the 'Engine Control Module' (ECM) may also be referred to as 'Powertrain Control
Module' (PCM).
2. Turn ignition 'ON' (engine not running).
3. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
5. Select 'Diagnosis' from the Session Type screen.
6. Select the 'Selected Symptoms' tab, and then select one of the following:
• Powertrain > Automatic transmission and transaxle > Automatic transmission and transaxle symptoms
> Gear selector malfunction > Gear position display flashing
• Powertrain > Engine system > Engine performance > Engine cuts out
• Powertrain > Engine system > Engine performance > Noises
• Electrical > Instruments > Warning lamps > Engine malfunction lamp > Lamp illuminated (and any of
the following DTCs P013A, P011B-21, P011B-22)
http://topix.landrover.jlrint.com/topix/service/document/564803
8/20/2015
Page 3 of 3
7. Select 'continue'.
8. Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure existing module Powertrain control module' option.
9. Follow all on-screen instructions to complete this task.
NOTE: once the Engine Control Module has been configured, the adaption values must be cleared
as follows.
10. Select the 'Selected Symptoms' tab, and then select one of the following:
• Powertrain > Automatic transmission and transaxle > Automatic transmission and transaxle symptoms
> Gear selector malfunction > Gear position display flashing
• Powertrain > Engine system > Engine performance > Engine cuts out
• Powertrain > Engine system > Engine performance > Noises
• Electrical > Instruments > Warning lamps > Engine malfunction lamp > Lamp illuminated (and any of
the following DTCs: P013A, P011B-21, P011B-22)
11. Select 'continue'.
12. Select the 'Recommendations' tab, and then select 'Run' to perform the ''Powertrain - Powertrain control
module adaption clear' option.
13. Follow all on-screen instructions to complete this task, ensuring all DTCs are cleared.
14. Exit the current session.
15. Disconnect the SDD and the battery power supply from the vehicle.
http://topix.landrover.jlrint.com/topix/service/document/564803
8/20/2015