LTB00866NAS1
Service Bulletin Details
Public Details for: LTB00866NAS1
"situation: a 'rattle' noise may be evident from the second row seat area of the vehicle. This will occur when the second row seat is pushed fully back and the valance trim is in contact with the quarter panel trim. Cause: this may be caus
Models from 2016
2016 LAND ROVER DISCOVERY SPORT |
Models from 2015
2015 LAND ROVER DISCOVERY SPORT |
Page 1 of 8 TECHNICAL BULLETIN LTB00866NAS1 22 DEC 2015 © Jaguar Land Rover North America, LLC NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land Rover service facility to determine whether this bulletin applies to a specific vehicle. SECTION: 501-10 'Rattle' Noise From The Second Row Seat Area AFFECTED VEHICLE RANGE: Discovery Sport (LC) Model Year: 2015-2016 VIN: 500429-549203 Assembly Plant: Halewood MARKETS: NAS CONDITION SUMMARY: Situation: A 'rattle' noise may be evident from the second row seat area of the vehicle. This will occur when the second row seat is pushed fully back and the valance trim is in contact with the quarter panel trim. Cause: This may be caused by the second row seat outer hinge mechanism cover having excessive free play at the rear. Action: Should a customer express this concern, follow the Service Instruction below. PARTS: LR073121 Outer Valance Cover - Right-hand (Glacier) Quantity: 1 LR073122 Outer Valance Cover - Right-hand (Cirrus) Quantity: 1 LR073123 Outer Valance Cover - Right-hand (Ivory) Quantity: 1 LR073125 Outer Valance Cover - Right-hand (Ebony Black/Ebony Quantity: 1 Black interior, Tan, Ebony/Pimento Red) LR073127 Outer Valance Cover - Right-hand (Almond) Quantity: 1 LR073130 Outer Valance Cover - Left-hand (Glacier) Quantity: 1 LR073132 Outer Valance Cover - Left-hand (Cirrus) Quantity: 1 LR073134 Outer Valance Cover - Left-hand (Ivory) Quantity: 1 LR073136 Outer Valance Cover - Left-hand (Ebony Black/Ebony Black interior, Tan, Ebony/Pimento Red) Quantity: 1 LR073139 Outer Valance Cover - Left-hand (Almond) Quantity: 1 WARRANTY: 6 NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to TOPix to obtain the latest repair time. 6 ,NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 2 of 8 DESCRIPTION SRO Outer Valence Cover - Renew - Pair 78.55.89.29 6 TIME (HOURS) CONDITION CODE CAUSAL PART 0.2 42 LR073121 NOTE: Normal Warranty procedures apply. COMPONENT LOCATION 1Component location. SERVICE INSTRUCTION: ~ NOTE: all illustrations: second row left-hand seat shown; second row right-hand seat similar. 1Remove the ISOFIX covers from the second row seat cushion. 2Remove the ISOFIX bezel. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 3 of 8 3Remove the ISOFIX bezel. 4Release the two clips and lift out the seat cushion. • Move the cushion away from the outer valance cover. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 4 of 8 s& cAUTION: care must be taken not to damage the component. Remove the seatback adjuster handle. El750 85 6Remove the Torx screw and the trim clip from the outer valance cover. • Remove and discard the outer valance cover. • Pull the rear edge of the outer valance cover upwards to release the outer valance cover from the mounting points. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 5 of 8 El 75084 7Install the new outer valance cover. • Rotate the new outer valance cover SMake sure the outer valance cover is installed correctly. • Fit the trim clip and the Torx bolt to secure the outer valance cover. • Torque: l.5Nm ± 0.5Nm. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 6 of 8 El 75084 9Install the seatback adjuster handle. t.185 36 lO~ NOTE: make sure the seat cushion locates properly into the two clips. Install the seat cushion. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 7 of 8 11Install the ISOFIX bezel. El857]4 12Install the ISOFIX bezel. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016 Page 8 of 8 13Install the two ISOFIX covers. 14Repeat steps 1-13 to the second row right-hand seat. http://topix.landrover.jlrext.com/topix/service/document/607423 1/7/2016