LTB00890NAS4

Page I of 4
TECHNICAL BULLETIN
LTB00890NAS4
15 JUL 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to do
the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in proper
vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your
vehicle. Contact an authorized Land Rover service facility to determine whether this bulletin applies to a specific vehicle.
This reissue replaces all previous versions. Please destroy all previous versions.
I Changes are highlighted in gray I
SECTION: 417-01
Squeak Noise From Tailgate Area While Driving
AFFECTED VEHICLE RANGE:
Discovery Sport (LC)
Model Year:
2015-2016
VIN:
500429-624854
Assembly
Halewood
Plant:
MARKETS:
NAS
CONDITION SUMMARY:
Situation: A 'squeak' noise may be evident from the rear of the vehicle while driving.
Cause: This may be caused by a clash condition between the tailgate finisher and inner tail lamp(s).
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
CZU0000l0
Spcr W/Shld GI
BNP3996
Circular patch
TOOLS:
Refer to Workshop Manual/Service Instruction for any required special tools.
WARRANTY:
, 6 NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must
be taken as guidance only. Always refer to TOPix to obtain the latest repair time.
, 6 NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity
of zero.
I
I
DESCRIPTION
Tail lamp - Modification
I
I
SRO
86.40.88.29
I
I
TIME (HOURS)
0.2
I
I
CONDITION CODE
07
I
I
CAUSAL PART
LR060908
I
I
, 6 NOTE: Normal Warranty procedures apply.
SERVICE INSTRUCTION:
1. Remove the inner tail lamp assemblies (see TO PIX Workshop Manual section 417-01: Exterior Lighting).
2. ~
NOTE: Repeat this step on both inner tail lamps.
Use a suitable cloth to clean the tail lamps in the areas shown.
http://topix.landrover.jlrext.com/topix/service/document/671825
8/3/2016
Page 2 of 4
3. ~
NOTE: Repeat this step on both inner tail lamps.
Use a suitable tool to cut the supplied tape circle in half and remove the
backing from the tape circle.
4. ~
NOTE: Repeat this step on both inner tail lamps.
Install the half-tape circle in the area shown.
• The half-tape circle will fold 90° and secure under the inner tail lamp.
5. The half-tape circle located and installed on the inner tail lamp.
http://topix.landrover.jlrext.com/topix/service/document/671825
8/3/2016
Page 3 of 4
El87468
6. Cut one seal
(CZUOOOOlO)
in half.
El94 780
7. ~
NOTE: Repeat this step on both inner tail lamps.
Install one half of the seal from Step 6 as shown.
http://topix.landrover.jlrext.com/topix/service/document/671825
8/3/2016
Page 4 of 4
I
I'
I
,,
1
El 9 385 4
8. Install the inner tail lamp assemblies (see TO PIX Workshop Manual section 417-01: Exterior Lighting).
http://topix.landrover.jlrext.com/topix/service/document/671825
8/3/2016