A14-030

Service Bulletin
(g)HONDA
14-030
March 31, 2017
06121 Version 3
Slapping or Clicking From Engine Area at Idle
Supersedes 14-030, dated June 18, 2014, to revise the information highlighted in yellow.
AFFECTED VEHICLES
Year
Model
2013
Accord
2014
Accord
2014
Accord
2014
Accord
2014
Accord
2014
Accord
2014
Accord
2014
Accord
Trim
L4
2-Door
2-Door
2-Door
4-Door
4-Door
4-Door
4-Door
L4
L4
L4
L4
L4
L4
L4
EX-L
LX-S
EX
LX
EX
EX-L
Sport
VIN Range
ALL
1HGCT1 B8.EA000001
1HGCT1 B3.EA000001
1HGCT1 B7.EA000001
1HGCR2F3.EA000001
1HGCR2F3.EA000001
1HGCR2F8.EA000001
1HGCR2FS.EA000001
thru
thru
thru
thru
thru
thru
thru
1HGCT1 B8.EA006773
1HGCT1 B3.EA006694
1HGCT1 B7.EA006524
1HGCR2F3.EA120107
1HGCR2F3.EA123948
1HGCR2F8.EA123438
1HGCR2FS.EA123058
REVISION SUMMARY
Under REQUIRED MATERIALS, the oil was changed to Full Synthetic Engine Oil, P/N 08798-9063 .
SYMPTOM
There is a slapping or clicking from the engine area at idle.
POSSIBLE CAUSE
Debris may be restricting oil flow to the cam chain auto-tensioner.
CORRECTIVE ACTION
Replace the cam chain auto-tensioner, and install a cam chain auto-tensioner filter.
PARTS INFORMATION
Part Name
Part Number
Quantity
Cam Chain Auto-Tensioner
14510-SA2-A01
1
Cam Chain Auto-Tensioner filter
14560-SA2-A00
1
Oil Filter
15400-PLM-A01
1
Part Name
Part Number
Quantity
Full Synthetic Engine Oil, 0W20 (one quart will top off about four vehicles)
08798-9063
1
HondaBond 4 (one tube will repair about 20 vehicles)
08717-1194
1
REQUIRED MATERIALS
Page 1 of 5
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools,
equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by "do-it-yourselfers," and you
should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information
applies, contact an authorized Honda automobile dealer.
© 2017 American Honda Motor Co., Inc. - All Rights Reserved
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation Number
Description
Flat Rate Time
Template ID
Failed Part Number
110114
Replace the cam chain tensioner
and install a tensioner filter.
0.6 hour
14-030A
14510-SA2-A01
Defect Code:
01801
Symptom Code: 04201
Skill Level:
Repair Technician
REPAIR PROCEDURE
1.
Remove the right front wheel.
2.
Remove the engine undercover.
3.
Remove the chain case cover.
4.
Clean the chain case cover and the chain case.
Page 2 of 5
5.
Turn the crankshaft counterclockwise until the cam chain auto-tensioner is compressed.
ORANKSHAFT
CAM CHAIN AUIT0-TEINSIONER
6.
Remove the cam chain auto-tensioner.
NOTE: Use a 1.2 mm diameter pin, a large paper clip, or similar item to hold the auto-tensioner arm in a locked
position for removal.
,
,
f-::
/
:.-:---
LOCK
7.
Remove the oil filter.
8.
Place a shop towel over the place on the engine block where the cam chain auto-tensioner mounts.
9.
Using shop air, place the air nozzle into the oil filter mounting adapter.
Page 3 of 5
QI!. F'I l,TEFI.
MOUNTIN,GAD.AIF'TER
10. Blow compressed air for 5 seconds through the oil passage to clear any debris before installing the new cam chain
auto-tensioner.
11. Install new a oil filter.
12. Install the cam chain auto-tensioner filter onto the new cam chain auto-tensioner.
NEW CAM CH!AIN
AUlU-TBNSIONER
CAM CHAINI
.AUlO-TENISIONER FILJER
13. Install the new cam chain auto-tensioner with filter, and torque the bolts to 12 N·m (9 lb-ft).
Page 4 of 5
NEW CAM CHAIN
AUTO-TENSION ER
AND FILTER
14. Apply a 2.5 mm diameter bead of hondabond 4 along the broken line.
CH!AIN CASE COVER
15. Install the chain case cover and torque the bolts to 12 N·m (9 lb-ft).
16. Install the engine undercover.
17. Install the right front wheel and torque the nuts to 108 N·m (80 lb-ft).
18. Top off the engine oil level.
19. Start the engine, warm up to operating temperature, and check for leaks.
Page 5 of 5