SP 215-021, Timi
Service Bulletin Details
Public Details for: SP 215-021, Timi
This repair requires the installation of a missing screw in the timing gear plate into the flywheel housing as the referenced in this installation procedure.
- 2017 -
Models from 2017
2017 VOLVO VAH |
2017 VOLVO VHD |
2017 VOLVO VN |
Volvo Trucks North America Greensboro, NC USA Service Program Trucks Date 4.2017 Group No. 215 021 Release Page 01 1(9) Timing Gear Plate Screw, Installation VN, VHD, VAH SP 215-021, Timing Gear Plate Screw, Installation (April 2017) This service program is limited to vehicles with US2017 emission engines with build dates of October 3, 2016 to November 17, 2016. This repair requires the installation of a missing screw in the timing gear plate into the flywheel housing as the referenced in this installation procedure. Clean any silicon debris from the screw hole before installation of the missing screw is required. The inner fender and the exhaust pipe behind the diffuser will require removal to gain access to the timing gear plate. Additionally, replacement of the exhaust clamps and gaskets are required during the reinstallation of the diffuser pipe. Follow the installation procedure outlined in this Service Program (SP). USA138901447 PV729-SP215-021 Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 Repair Parts W2122410 Timing Gear Plate Screw Installation Hardware Item Description Part Number Qty 1 Screw M8*30 984736 1 2 V-clamp 21060426 1 3 V-clamp 21021852 1 4 Gasket 21095721 2 Timing Gear Plate Screw Installation Procedure You must read and understand the precautions and guidelines in Service Information, group 20, "General Safety Practices, Engines" before performing this procedure. If you are not properly trained and certified in this procedure, ask your supervisor for training before you perform it. DANGER Do not attempt to repair or service this vehicle without having sufficient training, the correct service literature and the proper tools. Failure to follow this could make the vehicle unsafe and lead to serious personal injury or death. Page 2(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 1 Park the vehicle on a level surface and turn the front wheels to the left. 2 Apply the parking brake. 3 Place the transmission in neutral or park. 4 Install the wheel chocks. W7086748 5 Disconnect the cable from the battery’s negative terminal. W3086747 Page 3(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 6 Raise the hood. 7 If applicable, remove right side fairing and splash shield. W7112726 8 Loosen the clamps securing the exhaust pipe from the diffuser to the Diesel Particulate Filter (DPF) inlet pipe. W2122411 Page 4(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 9 Remove the exhaust pipe, clamps and gaskets. Note: Discard the clamps and gaskets, do not reuse. W2122412 10 Check the screw hole for any silicone or debris and clean as needed. W2122413 Page 5(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 11 Install the missing screw in the timing gear plate. 12 Tighten the screw to 24 ± 4 Nm (18 ± 3 ft-lb). W2122414 13 Install the exhaust pipe with new gaskets and clamps. W2122412 Page 6(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 14 Tighten the clamps to 12 ± 1 Nm (9 ± 1 ft-lb). W2122411 15 If applicable, install right side fairing and splash shield. W7112726 Page 7(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 16 Close the hood. 17 Connect the battery cable to the negative (ground) terminal. W3086747 18 Remove the wheel chocks. W7086759 Page 8(9) Volvo Trucks North America Service Program Date 4.2017 Group No. Release 215 021 01 Reimbursement This repair is covered by an authorized Service Program. Reimbursement is obtained via the normal claim handling process. UCHP Reimbursement Recall Status Vehicle inspected, repair not required 1- Inspected OK Vehicle repaired per instruction 2- Modified per instruction Labor Code Primary Labor Code (Timing Gear Plate Screw, Installation) 2150–02–09–02 0.5 hrs Time to take charge and determine campaign status 1700–16–01–01 0.3 hrs Causal Part 984736 SCC Code S7164 Authorization Number N/A Expiration Date 12-DEC-2017 Note: Take Charge Time is not included in the Labor Code for this operation. Take charge may be eligible but can only be used once per repair visit. If vehicle is having other warranty repairs performed, take charge should be charged to the warranty repair, otherwise take charge can be charged to this service program. Page 9(9)