Q627NAS1

Page 1 of 6
Q627NAS1
TECHNICAL BULLETIN
12 JAN 2017
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained,
professional Technicians with the knowledge, tools, and equipment required to
do the job properly and safely. It informs these Technicians of conditions that may
occur on some vehicles, or provides information that could assist in proper vehicle
service. The procedures should not be performed by 'do-it-yourselfers'. If you are
not a Retailer, do not assume that a condition described affects your vehicle.
Contact an authorized Land Rover service facility to determine whether this
bulletin applies to a specific vehicle.
INFORMATION
SECTION:
100-00
SUBJECT/CONCERN:
http://topix.landrover.jlrext.com/topix/service/procedure/754934/ODYSSEY_FSA/G2110...
1/31/2017
Page 2 of 6
Service Action: No Service Interval Required Message Displayed in the Message
Center
AFFECTED VEHICLE RANGE:
MODEL:
Discovery Sport (LC)
MODEL YEAR:
2015-2017
VIN:
501001-627258
ASSEMBLY PLANT:
Halewood
MARKETS:
NAS
CONDITION SUMMARY:
SITUATION:
An issue has been identified on certain vehicles within the listed Affected Vehicle
Range where no service interval required message is displayed in the message
center when an engine service is required after covering the appropriate
distance/time in service.
ACTION:
Retailers are required to HOLD affected new vehicles that are within your control
and refrain from releasing the vehicles for new vehicle sale pending completion of
the Service Instruction detailed in this Technical Bulletin. Unsold vehicles should
have this performed as part of the Pre-Delivery Inspection (PDI) process but must
have it completed prior to vehicle handover to the customer.
Affected vehicles already in the hands of customers should be updated at the next
available opportunity.
PARTS:
No parts required.
http://topix.landrover.jlrext.com/topix/service/procedure/754934/ODYSSEY_FSA/G2110...
1/31/2017
Page 3 of 6
SPECIAL TOOLS:


Jaguar Land Rover-approved Midtronics Battery Power Supply


Jaguar Land Rover-approved diagnostic tool with latest SDD software and
Calibration File
WARRANTY:
NOTE:
Check DDW to ensure that a vehicle is affected by this program prior to
undertaking any rework action.
http://topix.landrover.jlrext.com/topix/service/procedure/754934/ODYSSEY_FSA/G2110...
1/31/2017
Page 4 of 6
At the time of confirming a booking for vehicle repair, ensure that all outstanding
Recalls and Service Actions are identified to ensure the correct parts are available
and adequate workshop time is allocated for repairs to be completed at one visit.
Warranty claims must be submitted quoting the Program Code together with the
relevant Option Code. SRO and parts information is included for information only.
The Option Code(s) that allows for the drive in / drive out allowance can only be
claimed if the vehicle is brought back into the workshop for this action alone to be
undertaken.
Repair procedures are under constant review and therefore times / prices are
subject to change; those quoted here must be taken as guidance only. Refer to
TOPIx to obtain the latest repair time.
This program is valid for a limited time only. Warranty claims with a repair date
prior to the 30 December 2018 closure date must be submitted or payment
within 30 calendar days of completion of the repair.
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
Q627
B
CCF update
Q627
C
Q627
Q627
SRO
TIME
(HOURS)
PARTS/SUNDRY
CODE
QTY./VALUE
86.90.24
0.20
-
-
CCF update
Drive in/drive
out
86.90.24
02.02.02
0.20
0.20
-
-
D
CCF update
Transit
disengage/reengage
86.90.24
86.90.89.47
0.20
0.10
-
-
E
CCF update
Transit
disengage/reengage
Drive in/drive
out
86.90.24
86.90.89.47
02.02.02
0.20
0.10
0.20
-
-
Normal Warranty policies and procedures apply.
http://topix.landrover.jlrext.com/topix/service/procedure/754934/ODYSSEY_FSA/G2110...
1/31/2017
Page 5 of 6
SERVICE INSTRUCTION:
CAUTIONS:
◾ A Jaguar Land Rover-approved Midtronics battery power supply must
be connected to the vehicle battery during diagnosis / module
programming.
◾ Make sure all ignition ON/OFF requests are carried out; failure to
perform these steps may cause damage to control modules in the
vehicle.
NOTE:
The Jaguar Land Rover-approved diagnostic tool must be loaded with
SDD148.00 v.256 or later.
1
Connect the Jaguar Land Rover-approved Midtronics battery power
supply to the vehicle battery.
1
If required, remove the transit relay.
2
Turn ignition ON (engine not running).
3
Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle
and begin a new session.
4
Follow the on-screen prompts, allowing the tool to read the VIN and
identify the vehicle and initiating the data collect sequence.
5
Select Service Functions from the Session Type screen.
6
Select the Recommendations tab.
7
From the list or recommended candidates, select Run to perform the 'Car
configuration management - Session active car configuration' option.
http://topix.landrover.jlrext.com/topix/service/procedure/754934/ODYSSEY_FSA/G2110...
1/31/2017
Page 6 of 6
8
From the Session Active Car Configuration selection screen, select the AsBuilt file as the current Session Active CCF Source.
9
After making this selection, select the green ✓ continue button to update
vehicle Car Configuration File.
10
NOTE:
Make sure customer personalization settings are retained when
following the on-screen instructions. All necessary instructions
are provided on screen.
Follow all on-screen instructions to complete this task.
11
Follow all on-screen instructions to complete this task, ensuring all
Diagnostic Trouble Codes (DTC) are cleared.
1
12
If necessary, set the vehicle to 'Transportation Mode'.
When all tasks are complete, select the Session tab and then select the
Close Session option.
13
Disconnect the diagnostic tool and battery power supply from the vehicle.
1
If required, install the transit relay.
http://topix.landrover.jlrext.com/topix/service/procedure/754934/ODYSSEY_FSA/G2110...
1/31/2017