122-B4N2W-06

Service
Technical Information
95/14 ENU
WE61
6
WE61 - Tightening Screw for Targa Roof Emergency Operation on the Hydraulic Unit of the
Roof Drive Mechanism (Workshop Campaign)
Vehicle Type:
911 Targa 4 (991)/911 Targa 4S (991)
Model Year:
As of 2014 up to 2015
Concerns:
Screw for Targa roof emergency operation on the hydraulic unit of the roof drive mechanism.
Situation:
This is to inform you of a voluntary Workshop Campaign on the above-mentioned vehicles. There is
a possibility that the screw for Targa roof emergency operation on the hydraulic unit of the
roof drive mechanism on the affected vehicles may not have been tightened to the specified
tightening torque during the production process.
As a result, when the glass rear window is raised in order to top up engine oil, for example, the window
may not be held in position, but may slowly drop forward in direction of travel, thereby restricting the
available space.
Action
Required:
Tighten screw for Targa roof emergency operation on the hydraulic unit of the roof drive mechanism.
Affected
Vehicles:
The VIN(s) can be checked by using PIWIS Vehicle Information link to verify if the campaign affects the
vehicle. This campaign is scope specific to the VIN! Failure to verify in PIWIS may result in an improper
repair. This campaign affects 509 vehicles in North America.
Tools:
•
•
•
Torque wrench, 2 – 10 Nm (1.5 – 7.5 ftlb.), e.g. V.A.G 1783 - Torque wrench, 2-10 Nm (1.5-7.5
ftlb.)
Hexagon socket-wrench insert, a/f 6
Plastic wedge
Work
Procedure:
See Attachment “A”.
Claim
Submission:
See Attachment “B”.
2014© Porsche Cars North America, Inc.
AfterSales
Nov 10, 2014
Page 1 of 5
6
Service
WE61
ENU
Technical Information
95/14
Installation
Position:
1
2
Installation position of hydraulic unit
– Hydraulic unit of the roof drive mechanism
– Screw on hydraulic unit (tighten)
Attachment "A": Work Procedure
1
Nov 10, 2014
Page 2 of 5
Remove rear backrest at the right in direction of travel  Workshop Manual '724719 Removing and
installing rear backrest'.
AfterSales
2014© Porsche Cars North America, Inc.
Service
Technical Information
95/14 ENU
WE61
6
Figure 1
2014© Porsche Cars North America, Inc.
AfterSales
Nov 10, 2014
Page 3 of 5
6
Service
WE61
ENU
Technical Information
95/14
Figure 2
The rear seat backrests pivot bearing lower trim cover can be somewhat challenging to remove.
The releases on the front lower trim cover are accessed from underneath the sides of the trim cover.
Approximately midway along the bottom edge on each side of the cover. The sides of the trim cover
must be bent outwards. This will release the inside locking tabs from the slots in the metal frame
of the rear panel. The locking tabs must be released before the trim cover can slide forward. See
Figures 1 and 2.
2
Nov 10, 2014
Page 4 of 5
Remove trim panel for rear wall  Workshop Manual '703119 Removing and installing trim panel for
rear wall'.
AfterSales
2014© Porsche Cars North America, Inc.
Service
Technical Information
95/14 ENU
3
Tighten screw for Targa roof emergency operation
 Tightening screw -2- on the hydraulic unit 
Tightening screw -1- of the roof drive mechanism.
Tightening torque 3 Nm (2 ftlb.)
4
Install trim panel for rear wall  Workshop Manual
'703119 Removing and installing trim panel for rear
wall'.
5
Install rear backrest at the right in direction of
travel  Workshop Manual '724719 Removing and
installing rear backrest'.
6
WE61
6
Tightening screw
Enter the campaign in the Warranty and Maintenance booklet.
Attachment "C": Claim Submission - Workshop Campaign WE61
Warranty claims should be submitted via WWS/PQIS.
Open campaigns may be checked by using either the PIWIS Vehicle Information system or through PQIS
Job Creation.
Labor, parts, and sublet will be automatically inserted when Technician is selected in WWS/PQIS. If
necessary, the required part numbers will need to be manually entered into warranty system by the dealer
administrator.
Working time:
Tightening screw for Targa roof emergency operation on the hydraulic unit
of the roof drive mechanism.
Includes:
Removing and installing rear backrest at the right
Removing and installing trim panel for rear wall
Labor time: 20 TU
 Damage code WE61 066 000 1
Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. If a particular condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your authorized Porsche Dealer for the latest information
about whether a particular technical bulletin applies to your vehicle. Part numbers listed in these bulletins are for reference only. Always check with your authorized Porsche dealer to verify the current and
correct part numbers. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS
Tester are the ones that must be followed.
© Porsche Cars North America, Inc.
Dealership
Distribution
Routing
Service Manager
_______
Shop Foreman
_______
Service Technician
________
_______
_______
_______
Asst. Manager
_______
Warranty Admin.
_______
Service Technician
________
_______
_______
_______
Dr. Ing. h.c. F. Porsche AG is the owner of numerous trademarks, both registered and unregistered, including without limitation the Porsche Crest®, Porsche®, Boxster®, Carrera®, Cayenne®,
Cayman®, Macan®, Panamera®, Speedster®, Spyder®, 918 Spyder®, Tiptronic®, VarioCam®, PCM®, PDK®, 911®, RS®, 4S®, FOUR, UNCOMPROMISED®, and the model numbers and the
distinctive shapes of the Porsche automobiles such as, the federally registered 911 and Boxster automobiles. The third party trademarks contained herein are the properties of their respective owners.
Porsche Cars North America, Inc. believes the specifications to be correct at the time of printing. Specifications, performance standards, standard equipment, options, and other elements shown are
subject to change without notice. Some options may be unavailable when a car is built. Some vehicles may be shown with non-U.S. equipment. The information contained herein is for internal authorized
Porsche dealer use only and cannot be copied or distributed. Porsche recommends seat belt usage and observance of traffic laws at all times.
Printed in the USA
2014© Porsche Cars North America, Inc.
AfterSales
Nov 10, 2014
Page 5 of 5