5NPW6J3A02

GROUP
NUMBER
BODY
ELECTRICAL
Technical Service Bulletin
DATE
17-BE-001
MODEL(S)
JANUARY 2017
SUBJECT:
EQUUS (VI)
DRIVER AND PASSENGER DOOR SWITCH MODULE REPLACEMENT
Description: On certain Equus vehicles the Blue Link remote services for door lock/unlock function
is inoperative. The user is not able to lock or unlock the vehicle using Blue Link App or web portal.
This bulletin provides the procedure to replace the DDM (Driver Door Module) and ADM (Assisted
Door Module) to correct the condition.
DDM
ADM
Applicable Vehicles: 2015 – 2016 Equus (VI) With Active Blue Link Account
Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair
SUBJECT:
DRIVER AND PASSENGER DOOR SWITCH MODULE REPLACEMENT
Parts Information:
PART NAME
FIGURE / PART NUMBER
REMARK
PREVIOUS
NEW
93570-3N1554X
93570-3N1554XFFF
93570-3N0554X
93570-3N0554XFFF
93575-3N0554X
93575-3N0554XFFF
DDM
With Rear Window
Curtain
Without Rear Window
Curtain
ADM
Warranty Information:
OP CODE
OPERATION
OP TIME
NATURE
CAUSE
93570F02
DOOR AND WINDOW SWITCH REPLACEMENT
(BOTH SIDES)
0.4 M/H
M73
ZZ1
Service Procedure:
DDM (Driver Door Module) REPLACEMENT
1.
Remove 2 screws and one locking tab:
A
A. Screw at the door handle.
B. Screw in the door pocket handle.
B
C
C. Locking tab in the door jam.
See next page for more details.
TSB #: 17-BE-001
Page 2 of 6
SUBJECT:
DRIVER AND PASSENGER DOOR SWITCH MODULE REPLACEMENT
1A. Use a small flathead screwdriver, carefully
pry and remove the door handle cover.
Use a Phillips screwdriver, and remove the
screw.
1B. Use a small flathead screwdriver, lift and
remove the door pocket cover.
Use a Phillips screwdriver, and remove the
screw.
1C. Use a small and short Phillips screwdriver,
remove the plastic screw and then pull the
locking tab out.
TSB #: 17-BE-001
Page 3 of 6
SUBJECT:
2.
DRIVER AND PASSENGER DOOR SWITCH MODULE REPLACEMENT
Use a panel removal tool to remove the top
trim cover. Start with the top left corner.
Separate the top trim cover, disconnect the
tweeter connector, and remove it from the
door panel.
3.
To remove the door panel, gently pull the
door trim cover away from the door frame.
Start with the top right hand corner.
After pulling the door panel away from its
frame, disconnect the two wire harness
connectors and the door lock/unlock
mechanism.
TSB #: 17-BE-001
Page 4 of 6
SUBJECT:
4.
DRIVER AND PASSENGER DOOR SWITCH MODULE REPLACEMENT
Place the door panel on a clean surface.
Disconnect the DDM connectors.
5.
Use a Phillips screwdriver and remove the
11 screws as shown on the right.
6.
Separate the top half of the door panel from
the bottom half and remove the DDM.
TSB #: 17-BE-001
Page 5 of 6
SUBJECT:
7.
DRIVER AND PASSENGER DOOR SWITCH MODULE REPLACEMENT
Use a Phillips screwdriver and remove the
DDM mounting screws.
8.
Replace the DDM with the correct
countermeasure part.
9.
Install all removed parts in reverse order of
removal.
NOTICE
Ensure the door lock tab is in the unlock
position when reinstalling the door
lock/unlock mechanism.
10. Repeat procedures 1-8 for the passenger
door to replace the ADM.
11. Confirm all the door switches operates
normally.
Confirm all Blue Link remote services
(remote start, door lock/unlock, and etc.) are
functioning normally.
TSB #: 17-BE-001
Page 6 of 6