A17-063

Service Bulletin
September 15, 2017
17-063
07009 Version 1
Water Pump Seizes or the Drive Belt Is Shredded
AFFECTED VEHICLES
Year
Model
2013–16
Accord
2013–16
CR-V
Trim
L4 Only
ALL
VIN Range
ALL
ALL
SYMPTOM
The water pump seized or the drive belt shredded.
POSSIBLE CAUSES
The water pump bearing is out of specification.
CORRECTIVE ACTION
Replace the water pump and drive belt if damaged.
REQUIRED MATERIALS
Part Name
Part Number
Quantity
Honda Genuine Anitfreeze/Coolant Type 2
OL999-9011
1
PARTS INFORMATION
Part Name
Part Number
Quantity
Water Pump (2013–14 CR-V)
19200-R5A-A01
1
Water Pump (2015–16 CR-V,
2013–16 Accord)
19200-5A2-A01
1
Drive Belt (Accord with CVT)
31110-5A2-A01
1
Drive Belt (Accord with manual
transmission)
31110-5B0-Y01
1
Drive Belt (2013–14 CR-V)
31110-R5A-A01
1
Drive Belt (2015–16 CR-V)
31110-5LA-A02
1
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools,
equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and
you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this
information applies, contact an authorized Honda automobile dealer.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved
Page 1 of 7
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template ID
Failed Part
Number
113100
2013–16 Accord (All): Replace
the water pump only.
1.4 hrs
02301
03217
A17063A
19200-5A2-A01
113100
2013–16 Accord (CVT):
Replace the water pump and
drive belt (if necessary).
1.4 hrs
02301
03217
A17063B
19200-5A2-A01
113100
2013–16 Accord M/T):
Replace the water pump and
drive belt (if necessary).
1.4 hrs
02301
03217
A17063C
19200-5A2-A01
113100
2013–14 CR-V: Replace the
water pump only.
1.8 hrs
02301
03217
A17063D
19200-5A2-A01
113100
2013–14 CR-V: Replace the
water pump and drive belt
(if necessary).
1.8 hrs
02301
03217
A17063E
19200-5A2-A01
113100
2015–16 CR-V: Replace the
water pump only.
1.7 hrs
02301
03217
A17063F
19200-5A2-A01
113100
2015–16 CR-V: Replace the
water pump and drive belt
(if necessary).
1.7 hrs
02301
03217
A17063G
19200-5A2-A01
Skill Level:
Repair Technician
REPAIR PROCEDURE 2013–14 CR-V
1. Raise the vehicle on a lift, and make sure it is securely supported.
2. Remove the right front wheel.
3. Remove the bolts, then remove the clips that secure the front inner fender and the front splash shield to the body.
4. From under the front bumper, remove the clips.
5. From under the body, remove the clips, then pull out the front splash shield.
6. Loosen the drain plug, and drain the coolant.
Page 2 of 7
7. After the coolant has drained, tighten the drain plug securely.
8. Move the coolant reservoir.
9. Remove the coolant reservoir tank bracket.
10. Move the auto-tensioner using the belt tension release tool in the direction of the arrow to relieve tension from the
drive belt, then remove the drive belt.
11. Remove the idler pulley base.
Page 3 of 7
12. Remove the auto-tensioner.
13. Hold the pulley with the holder handle and the crankshaft pulley holder.
14. Remove the bolt with a socket and a breaker bar, then remove the crankshaft pulley.
15. Remove the water pump.
16. Inspect and clean the mating surface of the engine block.
Page 4 of 7
17. Install the water pump with a new O-ring, then torque the bolts to 12 N·m (9 lb-ft).
18. Clean the crankshaft pulley, the crankshaft, the bolt, and the washer. Lubricate with new engine oil as shown.
19. Install the crankshaft pulley, then hold the pulley with the holder handle and the crankshaft pulley holder.
20. Torque the bolt to 50 N·m (37 lb-ft) with a torque wrench and a 19mm socket. Do not use an impact wrench.
NOTE: If the pulley bolt or crankshaft are new, torque the bolt to 177 N·m (131 lb-ft), then remove the bolt, and
torque it to 50 N·m (37 lb-ft).
21. Tighten the pulley bolt an additional 90°.
Page 5 of 7
22. Install the auto-tensioner, and torque the bolts to 22 N·m (16 lb-ft).
23. Install the idler pulley base, and torque the bolts to 12 N·m (9 lb-ft).
24. Install the coolant reservoir tank bracket, and torque the bolts to 9.4 N·m (6.9 lb-ft).
25. Install the coolant reservoir and the drive belt.
26. Install the front splash shield.
27. Install the wheel, and torque the nuts to 108 N·m (80 lb-ft).
28. Fill the engine with coolant.
Page 6 of 7
REPAIR PROCEDURE 2013–16 ACCORD, 2015–16 CR-V
NOTE: This procedure is in an outline form. For more information, see the service information.
1. Drain the engine coolant.
2. Disconnect the 12-volt battery terminal (if required).
3. Remove the drive belt.
4. Remove the drive belt auto tensioner.
5. Remove the alternator (if required).
6. Remove the water pump.
7. Install the new water pump, and torque the bolts to 12 N·m (9 lb-ft).
8. Install the alternator, and torque the bolts to 45 N·m (33 lb-ft) (if required).
9. Install all remaining parts in the reverse order of removal.
10. Fill the engine coolant.
END
Page 7 of 7