A011700 2046377-

01 MY16/17 2.0TFSI, MIL on, DTC P001600
01 17 00 2046377/1 February 13, 2017.
Model(s)
Year
VIN Range
Vehicle-Specific Equipment
A5, A5
cabriolet,
Q5
2016 - 2017
All
2.0TFSI
Q3
2017
All
2.0TFSI
Condition
 MIL on.
 DTC P001600 (crankshaft camshaft correlation) stored in engine control module.
 Other DTC’s can also be stored at the same time.
Technical Background
On some MY 2016 and 2017 vehicles equipped with
2.0TFSI engines, engine codes (CPMB, CAED or
CCTA), DTC P001600 can be set due to a worn
intake side - camshaft bearing bridge thrust surface
(Figure 1).
Figure 1. Worn thrust surface.
Page 1 of 5
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Production Solution
Improved camshaft bearing bridge with 50% larger thrust surface in production starting 02/10/2017.
Service
If DTC P001600 (crankshaft camshaft correlation) is stored in the engine control module memory, proceed as
follows:
1. Measure the intake camshaft end play.
2. If intake camshaft endplay is less than 0.2mm this TSB does not apply, proceed with GFF to diagnose root
cause.
3. If intake camshaft end play is greater than 0.2mm, proceed to step 4.
4. Replace the camshaft bearing bridge (Figure 2) with part number 06H 103 144 K (Figure 3, improved part).
Note:
Do not use Part number 06H 103 144 J.
Figure 2. Original Part 06H 103 144 J.
Figure 3. Improved Part 06H 103 144 K
5. Drain engine oil, change the engine oil, and engine oil filter.
Page 2 of 5
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Note:
To prevent oil pan thread damage, only use torque wrench to tighten oil drain plug to 30Nm.
6. Check engine oil level and top up as needed.
7. Perform test drive to verify repair.
Warranty
Claim Type:
 110 up to 48 Months/50,000 Miles.
 G10 for CPO Covered Vehicles – Verify Owner.
 If vehicle is outside any warranty, this Technical Service Bulletin is informational
only.
Service Number:
1584
Damage Code:
0010
Q5, A5, and A5 cabriolet
Labor Operations:
Diagnostic Time:
Measure camshaft endplay
1505 9999
Max 30 TU
Camshaft bridge remove and install
1584 1914
100 TU
Change engine oil and filter
1701 9999
30 TU
GFF
0150 0000
Max 40 TU
Road test prior to service procedure
No allowance
0 TU
Road test after service procedure
0121 0004
10 TU
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2046377/1
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Page 3 of 5
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
Claim Type:
 110 up to 48 Months/50,000 Miles.
 G10 for CPO Covered Vehicles – Verify Owner.
 If vehicle is outside any warranty, this Technical Service Bulletin is
informational only.
Service Number:
1584
Damage Code:
0010
Q3
Labor Operations:
Diagnostic Time:
Measure camshaft endplay 1505 9999
Max 30 TU
Camshaft bridge remove
and install
1584 1914
120 TU
Change engine oil and
filter
1701 9999
30 TU
GFF
0150 0000
Max 40 TU
Road test prior to service
procedure
No allowance
0 TU
Road test after service
procedure
0121 0004
10 TU
Technical diagnosis at dealer’s discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:
As per TSB #2046377/1
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Part Number
Part Description
Quantity
Page 4 of 5
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.
06H 103 144 K
Camshaft bridge
06H 103 483 C
Gasket
Or
Replace only if damaged
06H 103 483 D
Gasket
N 105 724 03
Hexagon socket head bolt
Or
Application dependent
N 910 967 01
Hexagon socket head bolt
06J 115 403 Q
Oil filter
N 911 679 01
Drain plug
Or
Application dependent
N 013 815 7
Drain plug seal ring
01
01
01
01
01
Engine oil
4.9 quart
Additional Information
All parts and service references provided in this TSB (2046377) are subject to change and/or removal. Always
check your service manuals for the latest information.
©2017 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites without the prior expressed written permission of the publisher.
Page 5 of 5
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.