PDI - 2015 Audi

2015
Pre-Delivery Inspection
Technician Reference Document
Effective 11-3-2015-US
Version 1.0
Table of Contents
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.
Table of Contents
2-3
A3/S3/A3 TDI
4-5
A3 Cabriolet
6-7
A4/S4/allroad
8-9
A5/S5/RS5 Cabriolet
10-11	A5/S5/RS5 Coupe
12-14
A6/S6/A6 TDI
15-16
A7/S7/A7 TDI
17-18
A8/A8 L/A8 W12/S8/A8L TDI
19-20
Q3
21-23	Q5/Q5 hybrid/SQ5/Q5 TDI
24-25
Q7/Q7 TDI
26-27	R8 Coupe/R8 Spyder
28-29
TT/TTS Coupe and Roadster/TTRS
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 1
A3/S3/A3 TDI
Technician Reference Document
 ransport Mode Deactivation, DTC Check, Set Service
T
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM and check vehicle configuration
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Lighting and Windshield			
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers			
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Control Module list –> 5F –>
Guided Functions –> 5F Adaption). Also referred to as CD
Ripping. (Copying customer music from his device to the
hard drive of the vehicle) Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence 			
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc			
Under the Hood Inspection			
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature			
•      Perform a battery test
Perform a battery test and attach the results to the repair
order						
Exterior			
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)		
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into trunk
lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit under the trunk
floor
Effective 11-3-2014-US
Version 1.0
Interior			
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones			
Switches / Outlets and Windows			
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade operation			
•      Inspect mirrors for proper operation			
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)			
•      Inspect operation of all power outlets
Inspect operation of lighter, USB 5v power jack, aux. outlet
and rear outlet			
•      Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote					
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality			
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system		
•      Connect the dealer demo SIM card to verify system
connects to mobile network			
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)			
Model Year 2015 | Audi Pre-Delivery Reference Document | 2
A3/S3/A3 TDI
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
On-Hoist Inspection (continued)
•      Enable Google Earth (if equipped)			
•      Install wheel bolt covers and center caps as supplied
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network			
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)		
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance			
Media / Radio / SAT			
•      Verify HD Radio is turned “off”		
This can be found in the Radio/Settings Menu		
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)			
Settings			
Driving Performance			
•      Load Onboard Video Tutorials			
•      Calibrate rear view mirror			
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle			
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)		
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set “Music volume while parking” to 6 lines		
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)		
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test			
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”			
Change time zone appropriate to the dealer location		
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu		
•      Verify operation of speech dialogue system (if equipped)
Press the “Talk” button and verify several commands		
			
On-Hoist Inspection			
•      Inspect wheel bolts for proper torque		
Use torque wrench to verify			
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 3
A3 Cabriolet
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
•      Perform a battery test
Perform a battery test and attach the results to the repair
order
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit under the trunk
floor
•      Set spare tire pressure *1.8T ONLY
For the 1.8T A3 Cab, see separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet for proper inflation. For the 2.0T A3 Cabriolet, verify the inflatable spare
tire and compressor are present
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Effective 11-3-2014-US
Version 1.0
Interior
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, USB 5v power jack, aux. outlet
and rear outlet
•      Verify windows can be operated with the key
Verify windows roll down and sunroof opens when either the
key inserted in the door or by holding the unlock button on
the remote
Trunk Inspection
•      Set spare tire pressure *1.8T ONLY
For the 1.8T A3 Cab, see separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet for proper inflation. For the 2.0T A3 Cabriolet, verify the inflatable spare
tire and compressor are present
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the AT&T dealer demo SIM card to the vehicle and
make sure the system fully connects to the wireless network
(LTE symbol with service bars)(only applies if in an AT&T
service area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL > Settings >
Network connection (Wi-Fi) > select “Visible”)
Model Year 2015 | Audi Pre-Delivery Reference Document | 4
A3 Cabriolet
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
Convertible Functionality (if equipped)
•      Verify Audi connect Information Packet is present
•      Test operation of folding power top
Verify Audi connect Information Packet is present, including Audi brochure, AT&T brochure, customer SIM card, AT&T
Terms & Conditions (T&C)(if applicable)
Media / Radio / SAT
•      Verify HD Radio is turned “off”
Perform with engine running to conserve battery power
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
This can be found in the Radio/Settings Menu
Driving Performance
Settings
•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 5
A4/S4/allroad
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Under the Hood Inspection
Exterior (continued)
•      Verify power rear lid/tailgate is operational
*allroad only
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind right side
cover
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Verify operation of luggage cover
*allroad only
Lighting and Windshield
•      Test front washers (and rear/headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
Interior
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Effective 11-3-2014-US
Version 1.0
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent/ deflector at edge and sunshade
operation
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, aux. outlet under armrest, rear
outlet and cargo area (if equipped)
Model Year 2015 | Audi Pre-Delivery Reference Document | 6
A4/S4/allroad
Technician Reference Document
Audi connect (USA ONLY) (if equipped)
Settings (continued)
•      Check Wi-Fi hotspot functionality
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Settings
•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
•      Set “Music volume while parking” to 6 lines
Driving Performance
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 7
A5/S5/RS 5 Cabriolet
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind right side
cover
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Interior
•      Verify operation heated seats (if equipped)
Verify functionality of neck-level heating system (if
equipped)
•      Verify proper operation of climate control
Under the Hood Inspection
•      Check battery clamps for proper torque
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Re-torque if required
•      Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Effective 11-3-2014-US
Version 1.0
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, aux. outlet under armrest, and
rear outlet
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
Model Year 2015 | Audi Pre-Delivery Reference Document | 8
A5/S5/RS 5 Cabriolet
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
On-Hoist Inspection
•      Connect the dealer demo SIM card to verify system
connects to mobile network
•      Inspect wheel bolts for proper torque
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Convertible Functionality (if equipped)
•      Test operation of folding power top
Perform with engine running to conserve battery power
Driver Assistance
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Settings
Driving Performance
•      Load Onboard Video Tutorials
•      Calibrate rear view mirror
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 9
A5/S5/RS 5 Coupé
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind right side
cover
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet.
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Interior
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Under the Hood Inspection
Switches / Outlets and Windows
•      Check battery clamps for proper torque
•      Check operation of window, lock, and seat controls
Re-torque if required
•      Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all key buttons and features
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent and sunshade operation
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, aux. outlet under armrest, and
rear outlet
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 10
A5/S5/RS 5 Coupé
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
Settings (continued)
•      Connect the dealer demo SIM card to verify system
connects to mobile network
•      Verify Voice Activation is operating (if equipped)
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Settings
Driving Performance
•      Load Onboard Video Tutorials
•      Calibrate rear view mirror
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 11
A6/S6/A6 TDI
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate air suspension loading mode
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating (if equipped) Warning! Car body may
lower!
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Effective 11-3-2014-US
Version 1.0
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Trunk Inspection
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet.
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Interior
•      Verify operation heated/ventilated seats (if equipped)
Check both front and rear (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Verify rear climate control operation (if equipped)
Verify heating and cooling functions and open all rear panel
vents
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, seat ventilation and massage (if equipped), heated
seats and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent/ deflector at edge and sunshade
operation
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
Model Year 2015 | Audi Pre-Delivery Reference Document | 12
A6/S6/A6 TDI
Technician Reference Document
Switches / Outlets and Windows (continued)
Settings (continued)
•      Inspect operation of all power outlets
•      Set “Music volume while parking” to 6 lines
Inspect operation of lighter, aux. outlet under armrest,
under rear vent outlets, and in luggage compartment on passenger side
•      Verify operation of all interior lights
Including ambient lighting (if equipped)
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Settings
•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Effective 11-3-2014-US
Version 1.0
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers
Wheel bolt covers can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
•      Verify all vehicle Head-up Display functionality (if
equipped) (functionality listed in text box)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system plus with rear view
camera and top and/or corner view cameras (if equipped)
Driving Performance
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
Model Year 2015 | Audi Pre-Delivery Reference Document | 13
A6/S6/A6 TDI
Technician Reference Document
Driving Performance (continued)
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 14
A7/S7/A7 TDI/RS 7
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate air suspension loading mode
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating (if equipped) Warning! Car body may
lower!
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Exterior (continued)
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Trunk Inspection
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet.
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Interior
•      Verify operation heated/ventilated seats (if equipped)
Check both front and rear (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Verify rear climate control operation (if equipped)
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing
Effective 11-3-2014-US
Version 1.0
Verify heating and cooling functions and open all rear panel
vents
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, seat ventilation/heating (front and rear where applicable) and child safety features. Check rear lid opening and
closing with switch in door (ignition must be on)
•      Check panoramic sunroof operation
Verify open/close/vent/ deflector at edge and sunshade
operation
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, aux. outlet under armrest,
under rear vent outlets, and in luggage compartment on passenger side
Model Year 2015 | Audi Pre-Delivery Reference Document | 15
A7/S7/A7 TDI/RS 7
Technician Reference Document
Switches / Outlets and Windows (continued)
Settings (continued)
•      Verify operation of all interior lights
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Including ambient lighting (if equipped)
Change time zone appropriate to the dealer location
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Settings
•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
Effective 11-3-2014-US
Version 1.0
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers
Wheel bolt covers can be found in the PDI kit
•      Remove hoist access point trim covers (if equipped)
Prestige & S-Line only
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
•      Verify all vehicle Head-up Display functionality (if
equipped) (functionality listed in text box)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system plus with rear view
camera and top and/or corner view cameras (if equipped)
Driving Performance
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
Model Year 2015 | Audi Pre-Delivery Reference Document | 16
A8/A8 L/A8 W12/S8/A8L TDI
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate air suspension loading mode		
via Special Functions -> Service Work -> 34-Loading mode
activating/deactivating Warning! Car body may lower!
•      Deactivate vehicle transport mode		
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns 		
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)			
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence		
•      Set service reminder			
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc			
Exterior (continued)
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)		
Trunk Inspection
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers					
Interior			
•      Verify operation heated/ventilated seats (if equipped)
Check both front and rear (if equipped)			
•      Verify proper operation of climate control		
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Verify rear climate control operation (if equipped)
Under the Hood Inspection			
•      Check battery clamps for proper torque		
Re-torque if required			
•      Check engine oil level			
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature		
•      Perform a battery test			
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)				
Exterior			
•      Check all doors for proper power closing (if equipped)
For vehicles equipped with the power door closing feature,
check all doors for proper closing			
Effective 11-3-2014-US
Version 1.0
Verify heating and cooling functions and open all rear panel
vents 			
Switches / Outlets and Windows			
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, seat ventilation and massage (if equipped), heated
seats and child safety features			
•      Check panoramic sunroof operation			
Verify open/close/vent/ deflector at edge and sunshade
operation			
•      Check rear view mirror operation		
Check self-dimming function/lighting (if equipped)		
•      Inspect mirrors for proper operation			
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)			
•      Inspect operation of all power outlets		
Inspect operation of lighter, aux. outlet under armrest, and
rear outlet			
•      Verify operation of all interior lights 			
Including ambient lighting (if equipped)		
Model Year 2015 | Audi Pre-Delivery Reference Document | 17
A8/A8 L/A8 W12/S8/A8L TDI
Technician Reference Document
Audi connect (USA ONLY) (if equipped)			
Settings (continued)
•      Check Wi-Fi hotspot functionality			
•      Set dealership location in navigation (if equipped)
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network			
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)			
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network			
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)			
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present, including: Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)			
Media / Radio / SAT		
•      Verify HD Radio is turned “off”			
This can be found in the Radio/Settings Menu		
•      Verify operation of Rear Seat Entertainment (if equipped)
Rear Seat Entertainment/Rear MMI: Verify operation. Verify
the wireless headphones are present and pair them to the
RSE system (refer to RSE manual). When pairing the headphones, press and hold the on/off button for 4–5 seconds
until the light starts flashing quickly. Also verify the DVD
units operate			
Settings			
•      Load Onboard Video Tutorials			
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle			
•      Set “Music volume while parking” to 6 lines		
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)			
Effective 11-3-2014-US
Version 1.0
Set dealership location for following back to dealership during road test		
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”		
Change time zone appropriate to the dealer location		
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu		
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque		
Use torque wrench to verify			
•      Install wheel bolt covers			
Wheel bolt covers can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
•      Verify all vehicle Head-up Display functionality (if
equipped)		
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system plus with rear view
camera and top and/or corner view cameras (if equipped)
Driving Performance
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration		
Listen for abnormal noise/vibrations			
•      Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
Model Year 2015 | Audi Pre-Delivery Reference Document | 18
Q3
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire
Exterior (continued)
•      Verify power rear lid/tailgate is operational and set default
opening height
Adjust the trunk lid opening height to 75 inches (190 cm)
from the ground to the close button in the rear lid. Press and
hold the close button in the rear lid for at least four seconds
to program the opening height
Trunk Inspection
•      Set spare tire pressure
See separate “2015 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
Lighting and Windshield
•      Test front washers (and rear/headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Interior
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent/ deflector at edge and sunshade
operation
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of outlet in front of center console ad=nd
beind center console
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 19
Q3
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)
On-Hoist Inspection
•      Connect the dealer demo SIM card to verify system
connects to mobile network
•      Inspect wheel bolts for proper torque
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Media / Radio / SAT
Driving Performance
•      Verify HD Radio is turned “off”
•      Calibrate rear view mirror
This can be found in the Radio/Settings Menu
Settings
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 20
Q5/Q5 hybrid/SQ5/Q5 TDI
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Under the Hood Inspection
•      Check battery clamps for proper torque
•      Prepare the base bars for customer delivery (install bars
only upon customer request)
Install the rubber strips to the top of the base carrier bars
(do not install the carrier bars on the vehicle unless customer
has requested). Repackage the bars into the box if they are
not being installed on the vehicle. Retrieve the paper with
the torque wrench key code from the base carrier bar box.
Insert the paper with the key code into the owner’s literature
wallet. Record torque wrench key code in the VDF to ensure
it’s documented in the event the paper with the code is
misplaced
•      Verify power rear lid/tailgate is operational and set default
opening height
Adjust the trunk lid opening height to 77.7 inches (197 cm)
from the ground to the close button in the rear lid. Press and
hold the close button in the rear lid for at least four seconds
to program the opening height
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit behind spare tire.
Please note that in the hybrid it is located on the luggage
floor on the right side
Re-torque if required
•      Check engine oil level
Check engine oil level using Special Tool T40178 on a flat and
level surface
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Effective 11-3-2014-US
Version 1.0
Lighting and Windshield
•      Test front washers (and rear/headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Interior
•      Verify operation heated/ventilated seats (if equipped)
Check both front and rear (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent/ deflector at edge and sunshade
operation
Model Year 2015 | Audi Pre-Delivery Reference Document | 21
Q5/Q5 hybrid/SQ5/Q5 TDI
Technician Reference Document
Switches / Outlets and Windows (continued)
Settings (continued)
•      Inspect mirrors for proper operation
•      Set “Music volume while parking” to 6 lines
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, aux. outlet under armrest, rear
outlet and cargo area (if equipped)
Audi connect (USA ONLY) (if equipped)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Settings
•      Load Onboard Video Tutorials
Load Onboard Video Tutorials> Turn ignition on> Insert the
Onboard DVD into the DVD Drive> Select the CAR function
button. System will initialize>Select the Owner’s Man. function by selecting the upper right control button> Select
“Yes”> Select “CD/DVD”> Select “Start update”> Turn off
ignition to start update (the update will take approx. 5 minutes)> Once completed, remove the disk and place back into
the case for the next vehicle
Effective 11-3-2014-US
Version 1.0
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Driving Performance
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
Model Year 2015 | Audi Pre-Delivery Reference Document | 22
Q5/Q5 hybrid/SQ5/Q5 TDI
Technician Reference Document
•      Verify engine Start-Stop System functionality (if equipped)
Start-Stop-System info (if applicable): Verify the velum
sticker is on the start/stop button. Remove the start/stop
information card from the car kit and place it in the glove box
with the owner’s manuals. Additional supply can be ordered
via the Brand Store on AccessAudi
Hybrid Technology (if equipped)
•      Check MMI and instrument cluster for proper operation
mode indication
Verify green lights while EV or electrical drive, orange while
combustion engine active, etc
•      Verify charging while braking in recuperation range
See power meter for details
•      Verify EV button is operating
Push the EV button at a speed below 65 mph and check for
lights on EV button and instrument cluster. EV mode may
or may not activate based on current operational criteria as
described in the owner’s manual
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 23
Q7/Q7 TDI
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. (Copying customer music from
his device to the hard drive of the vehicle) Perform 3 button
reset of the MMI to complete the activation. Refer to the
owners manual for model specific button sequence
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Exterior (continued)
•      Install the hitch cover cap (if equipped)
The cap is located in the cargo area
•      Verify power rear lid/tailgate is operational and set default
opening height
Adjust the trunk lid opening height to 75 inches (190 cm)
from the ground to the close button in the rear lid. Press and
hold the close button in the rear lid for at least four seconds
to program the opening height
Lighting and Windshield
•      Test exterior lighting functions
Including that rear lighting transfers between tailgate and
bumper when tailgate is operated
•      Test front washers (and rear/headlight washers if
equipped)
Headlights must be on to test functionality of the headlight
washers
Interior
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Check engine oil level via the MMI – fill oil to the max level
when the vehicle is at operating temperature
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> Service work. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)
Exterior
•      Check all key buttons and features
Check key functionality including seat and steering wheel
position memory; verify vehicle starts and runs with all keys
and the start/stop button; verify all doors and trunk manually and remotely lock/unlock with all keys, including all door
handle sensors with the Advanced Key (if equipped)
Effective 11-3-2014-US
Version 1.0
•      Verify operation heated/ventilated seats (if equipped)
Check both front and rear (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Verify rear climate control operation (if equipped)
Verify heating and cooling functions and open all rear panel
vents
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Check panoramic sunroof operation
Verify open/close/vent/deflector at edge and sunshade operation (front and rear). Synchronize if necessary
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of power outlet(s) in center console, in rear
of center console, and in cargo area
Model Year 2015 | Audi Pre-Delivery Reference Document | 24
Q7/Q7 TDI
Technician Reference Document
Audi connect (USA ONLY) (if equipped)
On-Hoist Inspection
•      Check Wi-Fi hotspot functionality
•      Inspect wheel bolts for proper torque
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Connect the dealer demo SIM card to verify system
connects to mobile network
Connect the dealer demo SIM card to the vehicle and make
sure the system fully connects to 2G or 3G (2G or 3G symbol
with Box surrounding it) (only applies if in a T-Mobile service
area)
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol
•      Turn on the wireless network
Ensure the wireless network is turned on (TEL function button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system plus with rear view
camera and top and/or corner view cameras (if equipped)
•      Verify Audi connect Information Packet is present
Verify Audi connect Information Packet is present including Audi brochure, T-Mobile brochure, customer SIM card,
T-Mobile Terms & Conditions (T&C)(if applicable)
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Driving Performance
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Settings
Listen for abnormal noise/vibrations
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera).
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 25
R8 Coupé/R8 Spyder
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate the anti-theft function for the Navigation DVD
Deactivate the anti-theft function for the Navigation DVD
using the Scan Tool. Follow the process outlined in TSB
2013790
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
Interior
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Settings
•      Set clock and date
Set clock and date to local time/date using correct format
•      Set dealership location in navigation (if equipped)
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
•      Perform a battery test
Check the battery prior to starting engine with MCR340A.
Attach printout to the repair order
Set dealership location for following back to dealership during road test
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
Exterior
•      Check all key buttons and features
Verify vehicle starts and runs with all keys; verify all doors
manually and remotely lock and unlock with all keys
Trunk Inspection
•      Install wheel bolt removal tool into luggage compartment
tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key into luggage compartment tool kit
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Effective 11-3-2014-US
Version 1.0
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Convertible Functionality (if equipped)
•      Test operation of folding power top
Perform with engine running to conserve battery power
Model Year 2015 | Audi Pre-Delivery Reference Document | 26
R8 Coupé/R8 Spyder
Technician Reference Document
Driver Assistance
•      Verify operation of Audi parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Driving Performance
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 27
TT/TTS Coupé and Roadster/TT RS
Technician Reference Document
Transport Mode Deactivation, DTC Check, Set Service
Reminder
•      Deactivate the anti-theft function for the Navigation DVD
Deactivate the anti-theft function for the Navigation DVD
using the Scan Tool. Follow the process outlined in TSB
2013790
•      Deactivate vehicle transport mode
Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Perform an SVM specified /actual comparison
via Special Functions -> Software Version Management (SVM)
•      Perform any open campaigns
Follow instructions listed in campaign documentation
•      Set service reminder
via Special functions –> Service work –> 17-PDI-resetting SRI
at PDI, counter reset, etc
Under the Hood Inspection
•      Check battery clamps for proper torque
Re-torque if required
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
•      Perform a battery test
Check the battery prior to starting engine with MCR340A.
Attach printout to the repair order
Exterior
•      Check all key buttons and features
Verify vehicle starts and runs with all keys; verify all doors
manually and remotely lock and unlock with all keys
Interior
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents for all zones
Switches / Outlets and Windows
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, RH tilt in reverse, and memory
(if equipped)
•      Inspect operation of all power outlets
Inspect operation of lighter, aux. outlet under armrest, and
rear outlet
Settings
•      Set clock and date
Set clock and date to local time/date using correct format
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership during road test
•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify Voice Activation is operating (if equipped)
Press the “Talk” button and verify several commands
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Trunk Inspection
•      Install wheel bolt removal tool into luggage compartment
tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key into luggage compartment tool kit
Lighting and Windshield
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2015 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 28
TT/TTS Coupé and Roadster/TT RS
Technician Reference Document
Convertible Functionality (if equipped)
•      Test operation of folding power top
Perform with engine running to conserve battery power
Driving Performance
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
Effective 11-3-2014-US
Version 1.0
Model Year 2015 | Audi Pre-Delivery Reference Document | 29