A271627 2036392-
Service Bulletin Details
Public Details for: A271627 2036392-
This technical bulletin provides software instructions for vehicle vibration between 1000 rpm and 3000 with two dtcs.
Models from 2015
| 2015 AUDI A8 |
| 2015 AUDI RS7 |
| 2015 AUDI S6 |
| 2015 AUDI S7 |
| 2015 AUDI S8 |
Models from 2014
| 2014 AUDI A8 |
| 2014 AUDI RS7 |
| 2014 AUDI S6 |
| 2014 AUDI S7 |
| 2014 AUDI S8 |
Models from 2013
| 2013 AUDI A8 |
| 2013 AUDI RS7 |
| 2013 AUDI S6 |
| 2013 AUDI S7 |
| 2013 AUDI S8 |
27 Vibrations felt at 1000 rpm and 3000 rpm 27 16 27 2036392/5 October 31, 2016. Supersedes Technical Service Bulletin Group 27 number 15-25 dated March 20, 2015 for reasons listed below. Model(s) Year VIN Range Vehicle-Specific Equipment S6, S7, RS 7, A8, S8 2013 - 2015 All 4.0 TFSI Condition REVISION HISTORY Revision Date Purpose 5 - Revised Service (Revised entire section) 4 03/20/2015 Revised header data (Added model years) Revised Service (Revised entire section) Revised Warranty (Updated Labor Operations) 3 04/24/2014 Revised Warranty (Updated damage code) Vibrations are felt at 1000 rpm and 3000 rpm. The following DTCs may be stored in the sub-frame mount control module, J931 (address word BA): DTC B201000 (No basic setting) DTC B200500 (Data record invalid) Technical Background The basic settings of the active engine mounts in the sub-frame mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off. Page 1 of 4 © 2016 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Production Solution Optimized J931 control module software. Service Before proceeding, attempt to verify the vibration concern by performing a test drive. During the test drive, observe the vehicle in the following conditions: In 3rd or 4th gear (tip mode) at 2500 to 3200 rpm. Approximately 50% throttle input. If the condition cannot be reproduced, this bulletin does not apply. If the condition can be reproduced, follow the instructions for the appropriate model below: For S6, S7, and RS 7: Update the J931 control module: 1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions. 2. Update the J931 control module using the SVM action code as listed in the table below, if necessary: Model Engine S6, S7, RS 7 4.0T Old Software Part Number Old Software Version (or lower) New Software Part Number 4H0907145 0006 4H0907145B New Software Version (or higher) 0008 SVM Code Input BAA001 3. Perform J931 basic settings after SVM is completed. Tip: If J931 basic settings are not performed after the SVM update, the motor mounts will not properly dampen engine movement and the claim will be denied. 4. If condition is eliminated, release the vehicle. Page 2 of 4 © 2016 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. For A8 and S8: Update the J931 control module: 1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions. 2. Update the J931 control module using the SVM action code as listed in the table below, if necessary: Model Engine A8, S8 4.0T Old Software Part Number Old Software Version (or lower) New Software Part Number 4H0907145 0006 4H0907145B New Software Version (or higher) 0008 SVM Code Input BAA001 3. Perform J931 basic settings after SVM is completed. Tip: If J931 basic settings are not performed after the SVM update, the motor mounts will not properly dampen engine movement and the claim will be denied. 4. Align the exhaust system according to Elsa at Repair Manual >> Engine >> Engine Mechanical, Fuel Injection and Ignition >> 26 Exhaust Systems, Emission Controls >> Exhaust System, Installing without Tension. 5. Perform J931 basic settings after aligning the exhaust. 6. If condition is eliminated, release the vehicle. If condition is not eliminated, perform TSB 2045720: 26 A8/S8 4.0TFSI, vibrations between 1000 and 3000 rpm while driving. a. If condition is eliminated after performing the TSB, release the vehicle. Warranty Claim Type: 110 up to 48 Months/50,000 Miles. G10 for CPO Covered Vehicles – Verify Owner. Page 3 of 4 © 2016 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. If vehicle is outside any warranty, this Technical Service Bulletin is informational only. Service Number: 1039 Damage Code: 0041 Labor Operations: SVM update 1039 2599 Time stated on diagnostic protocol (Max 50 TU) Check SVM update already performed XXXX XXXX 10 TU Align exhaust system after J931 basic setting 2625 9999 20 TU Road test prior to service procedure 0121 0002 10 TU Road test after service procedure 0121 0004 10 TU Diagnostic Time: Technical diagnosis at dealer’s discretion (Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details) Claim Comment: As per TSB #2036392/5 All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. Additional Information All parts and service references provided in this TSB (2036392) are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information. The following Technical Service Bulletin(s) will be necessary to complete this procedure: TSB 2045720, 26 A8/S8 4.0TFSI, vibrations between 1000 and 3000 rpm while driving. ©2016 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. Page 4 of 4 © 2016 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.