5NP-X3Q5Y-02

GROUP
CAMPAIGN
DATE
Technical Service Bulletin
SUBJECT:
JANUARY, 2018
NUMBER
18-01-004
MODEL(S)
GENESIS (BH)
EQUUS (VI)
2011-2014 GENESIS (BH) AND 2011-2016 EQUUS (VI)
ANCHOR PRETENSIONER LABEL INSTALLATION
(SERVICE CAMPAIGN T2R)
This TSB supersedes TSB# 17-01-072 and modifies the applicable model years of Genesis
(BH) vehicles.
 IMPORTANT
*** Retail Vehicles ***
Dealers must perform this Service Campaign on all affected vehicles whenever an affected vehicle
is in the shop for any maintenance or repair.
When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty
Vehicle Information" screen via WEBDCS to identify open Campaigns.
 IMPORTANT
For Genesis (BH) vehicles, please use the same labels as used on Recalls 160/169.
For Equus (VI) vehicles, please use labels only provided for Service Campaign T2R.
Description: The front seat belt assembly incorporates a seat belt anchor pretensioner fastened to the
vehicle’s front seat frame. During vehicle assembly, the anchor pretensioner is fastened to the front
seat frame prior to being connected to the seat belt linkage. If, during vehicle repair, the connector
does not fully latch when the linkage was pressed onto the connector, the seat belt can detach from the
anchor pretensioner. If the seat belt linkage detaches from the anchor pretensioner in a collision, the
risk of injury to the occupant is increased.
This bulletin describes the procedure to install warning labels on the driver’s and/or passenger’s seat
belt assemblies to prevent potential improper reattachment of the anchor pretensioners.
NOTICE
Please note this is a simple installation that can be performed in the dealer’s service drive
in less than 5 minutes.
Applicable Vehicles:
2011-2014MY Genesis (BH) vehicles
2011-2016MY Equus (VI) vehicles
Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair
SUBJECT: ANCHOR PRETENSIONER LABEL INSTALLATION (SERVICE CAMPAIGN T2R)
Parts Information:
Genesis (BH): Driver side ONLY
Part Name
Part Number
Previous
New
Part Image
Warning Label,
Anchor
Pre-Tensioner
N/A
20114-1882R
Remarks
1 label needed
per Genesis (BH)
vehicle
Note: For Genesis (BH), each dealer was provided one roll of 1000 labels for Recall 160 & Recall 169
which can also be used for Service Campaign T2R. Additional rolls of 1000 labels can be ordered
through your facing PDC.
Equus (VI): Driver & Passenger sides
Part Name
Part Number
Previous
New
Part Image
Warning Label,
Anchor
Pre-Tensioner
RH&LH
N/A
20114-1883R
Remarks
1 set of LH & RH
labels needed
per Equus (VI)
vehicle
Note: For Equus (VI), each dealer will initially be provided one sheet that contains 12 sets of LH & RH
labels. Additional sheets of 12 sets of LH & RH labels can be ordered through your facing PDC.
Warranty Information:
Model
Op Code
Operation
Op Time
Causal Part
Nature
Code
Causal
Code
Genesis (BH)
Equus (VI)
70C117R0
Anchor Pretensioner
Label Installation
0.2 M/H
11251-06161
I92
ZZ6
NOTES:
 Submit Claim on Campaign Claim Entry Screen
 If a part is found in need of replacement while performing Service Campaign T2R and the affected
part is still under warranty, submit a separate warranty claim using the same repair order. If the
affected part is out of warranty, submit a Prior Approval Request for goodwill consideration prior to
performing the work.
TSB #: 18-01-004
Page 2 of 4
SUBJECT:
SUBJECT: ANCHOR PRETENSIONER LABEL INSTALLATION (SERVICE CAMPAIGN T2R)
Service Procedure:
1.
Locate the driver anchor pretensioner (A)
near the lower B pillar trim (B) and move
the front seat appropriately to easily access
the anchor pretensioner.
B
A
2.
Visually inspect the inboard surface of the
Equus (VI):
linkage element (C) and make sure the
surface is free from any debris.
Note: if necessary, wipe the surface with
a clean, dry cloth.
Genesis (BH):
C
TSB #: 18-01-004
Page 3 of 4
SUBJECT:
SUBJECT: ANCHOR PRETENSIONER LABEL INSTALLATION (SERVICE CAMPAIGN T2R)
3.
Equus (VI):
Peel off the label (D) and align it with the
center hole (E) and top horizontal line (F) of
the linkage element.
Genesis (BH):
NOTICE
NOTE: For Genesis (BH), the
anchor pretensioner is located
on the driver side ONLY.
D
F
E
4.
Firmly press down on the label to ensure it
adheres to the surface of the linkage
element.
Note: Green “LOCKED” arrows (G)
should align with the latch slot.
Equus (VI):
Genesis (BH):
G
5.
For Equus (VI), locate the passenger’s
anchor pretensioner and move the
passenger seat appropriately, and repeat
Steps 2 through 4 to install the RH label
(H).
Equus (VI):
H
TSB #: 18-01-004
Page 4 of 4
SUBJECT: