B17-012

Service Bulletin
17-012
October 18, 2017
07564 Version 4
Product Update: TLX 9-Speed Transmission Warmer (Transmission
Previously Replaced for Transmission Warmer Leaking)
Supersedes 17-011, dated October 6, 2017, to revise the information highlighted in yellow
AFFECTED VEHICLES
Year
Model
2015–16
TLX
Trim
All with 9-speed A/T
VIN Range
Check the iN VIN status for eligibility
REVISION SUMMARY
Under REQUIRED MATERIALS, order the Honda ATF P/N to complete this campaign.
BACKGROUND
Some 9-speed transmission warmers were improperly manufactured and allow the engine coolant and ATF to mix. If the
fluids mix, the engine and transmission may be permanently damaged and require replacement. These vehicles
previously had the transmission replaced because the transmission warmers leaked. In rare cases, these vehicles may
have also overheated but because the issue was under investigation, a standard repair procedure hadn’t been
developed. Further action is needed before the vehicle is completely repaired.
Make sure you review this bulletin in its entirety before starting. There are multiple repairs available, and the correct one
for the vehicle you are working on is based on your inspection and customer interview responses.
CLIENT NOTIFICATION
Owners of affected vehicles will be sent a notification of this campaign.
Do an iN VIN status inquiry to make sure the vehicle is shown as eligible.
Some vehicles affected by this campaign may be in your new or used vehicle inventory. Repair these vehicles before
they are sold.
SERVICE ADVISOR
Ask the client if the vehicle overheated, for example, if the MID showed a message Stop Driving Engine Temperature
Too Hot or there was steam from under the hood. Other signs include coolant leaking from the radiator cap or the
coolant reserve tank.
OR
The vehicles in this campaign had the transmission previously replaced. The vehicle may have overheated due to the
warmer leaking on the previous repair; ask the customer if the vehicle overheated before the transmission was
replaced. This will help your technician decide what repair needs to be done.
Write down the client responses on the RO.
NOTE: Any engine replaced without this documentation on the signed RO will be subject to debit.
CLIENT INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment,
and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not
assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies,
contact an authorized Acura automobile dealer.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved
Page 1 of 65
CORRECTIVE ACTION
Inspect the warmer, and based on your inspection and interview with the customer, do one of the following:
• Replace the transmission warmer, replace the radiator, coolant hoses, thermostat, coolant reserve tank,
2 ECT sensor (1 and 2) O-rings, and flush the cooling system.
• Replace the transmission, radiator, coolant hoses, thermostat, coolant reserve tank, 2 ECT sensor (1 and 2)
O-rings, and flush the cooling system.
• Replace the short block, cylinder heads, radiator, thermostat, coolant reserve tank, all of the coolant hoses, 2 ECT
sensor (1 and 2) O-rings, water passage, water connecting pipe, and flush the heater core.
• Replace the radiator, coolant hoses, thermostat, coolant reserve tank, 2 ECT sensor (1 and 2) O-rings, and flush
the cooling system.
• Replace the short block, cylinder heads, transmission, radiator, thermostat, coolant reserve tank, all of the coolant
hoses, 2 ECT sensor (1 and 2) O-rings, water passage, water connecting pipe, and flush the heater core.
The flowchart below provides a summary to help navigate the inspection and repair procedure. Make sure you read the
service bulletin steps thoroughly for the detailed repair information.
Start
REPAIR PROCEDURE A
- Replace radiator and
hoses
- Flush engine
No
Did the vehicle
overheat?
Good
Check the ATF warmer date.
Yes
No Good
REPAIR PROCEDURE B
Replace the engine,
radiator, and hoses
-Flush heater core
Remove the ATF warmer and
check for leaks.
REPAIR PROCEDURE A
- Replace the ATF warmer if the
date is within affected range.
- Flush engine
No
Does ATF warmer leak?
No
Did the vehicle overheat?
Yes
REPAIR PROCEDURE B
- Replace engine, radiator, and
hoses.
- Replace the ATF warmer if the
date is within affected range.
- Flush heater core
Yes
Did the vehicle overheat?
No
REPAIR PROCEDURE C
- Replace transmission, radiator,
and hoses.
- Flush engine.
Yes
REPAIR PROCEDURE D
- Replace engine, transmission,
radiator, and hoses
- Flush heater core
End
Page 2 of 65
WARRANTY CLAIM INFORMATION
NOTE: Very few engine blocks should be replaced because of overheating. Replaced engine blocks may be called in to
validate damage to the original block.
Inspection and REPAIR PROCEDURE A
Operation
Number
2185B5
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
Inspect the ATF warmer
manufacture date, check
vehicle for overheating
and do REPAIR
PROCEDURE A
3.7 hr
6ZF00
KG500
B17012A
06200-5J4-A71
3.7 hr
6ZF00
KG500
B17012B
06200-5J4-A71
- Replace radiator and
hoses
- Flush engine
2185B5
Inspect the ATF warmer
manufacture date, check
vehicle for overheating
and do REPAIR
PROCEDURE A
- Replace radiator and
hoses
- Flush engine
A
Add if ATF warmer
tested because of
manufacture date.
2.1 hr
- Replace ATF warmer
Page 3 of 65
Inspection and REPAIR PROCEDURE B
Operation
Number
2185B6
Description
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
2WD BASE/TECH - Inspect
the ATF warmer
manufacture date, check
vehicle for overheating and
do REPAIR PROCEDURE
B
11.8 hr
6ZF00
KG500
B17012C
06200-5J4-A71
11.8 hr
6ZF00
KG500
B17012D
06200-5J4-A71
-Replace engine, radiator,
and hoses
- Flush heater core
- Includes updating
PCM/TCM, idle learn and
alignment
2185B6
2WD ADV - Inspect the ATF
warmer manufacture date,
check vehicle for
overheating and do REPAIR
PROCEDURE B
-Replace engine, radiator,
and hoses
- Flush heater core
- Includes updating
PCM/TCM, idle learn and
alignment
A
2185B7
Add if ATF warmer tested
and replaced because of
manufacture date.
0.9 hr
AWD BASE/TECH - Inspect
the ATF warmer
manufacture date, check
vehicle for overheating and
do REPAIR PROCEDURE
B
12.2 hr
6ZF00
KG500
B17012E
06200-5J4-A71
12.2 hr
6ZF00
KG500
B17012F
06200-5J4-A71
- Replace engine, radiator,
and hoses
- Flush heater core
- Includes updating
PCM/TCM, idle learn and
alignment
2185B7
AWD ADV - Inspect the
ATF warmer manufacture
date, check vehicle for
overheating and do REPAIR
PROCEDURE B
- Replace engine, radiator,
and hoses
- Flush heater core
- Includes updating
PCM/TCM, idle learn and
alignment
A
Add if ATF warmer tested
and replaced because of
manufacture date.
0.9 hr
Page 4 of 65
Inspection and REPAIR PROCEDURE C
NOTE:
• Very few engine blocks should be replaced because of overheating. Replaced engine blocks may be called in to
validate damage to the original block.
• Replacement of the engine block and/or transmission requires DPSM authorization.
Operation
Number
2185B8
Description
Transmission
Replacement
Number
Flat
Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part
Number
2WD BASE/TECH Inspect the ATF warmer
manufacture date and
check vehicle for
overheating and do
REPAIR PROCEDURE C
06200-5J4-A71RM
10.5 hr
6ZF00
KG500
B17012G
06200-5J4-A71
06200-5J4-A81RM
10.5 hr
6ZF00
KG500
B17012H
06200-5J4-A71
06200-5L9-A72RM
10.9 hr
6ZF00
KG500
B17012I
06200-5J4-A71
06200-5L9-A81RM
10.9 hr
6ZF00
KG500
B17012J
06200-5J4-A71
- Replace transmission,
radiator, and hoses
-Flush engine
- Includes updating
PCM/TCM, idle learn and
alignment
2185B8
2WD ADV - Inspect the
ATF warmer manufacture
date and check vehicle for
overheating and do
REPAIR PROCEDURE C
- Replace transmission,
radiator, and hoses
-Flush engine
- Includes updating
PCM/TCM, idle learn and
alignment
2185B9
AWD BASE/TECH Inspect the ATF warmer
manufacture date and
check vehicle for
overheating and do
REPAIR PROCEDURE C
- Replace transmission,
radiator, and hoses
-Flush engine
- Includes updating
PCM/TCM, idle learn and
alignment
2185B9
AWD ADV - Inspect the
ATF warmer manufacture
date and check vehicle for
overheating and do
REPAIR PROCEDURE C
- Replace transmission,
radiator, and hoses
-Flush engine
- Includes updating
PCM/TCM, idle learn and
alignment
Page 5 of 65
Inspection and REPAIR PROCEDURE D
NOTE:
• Very few engine blocks should be replaced because of overheating. Replaced engine blocks may be called in to
validate damage to the original block.
• Replacement of the engine block and/or transmission requires DPSM authorization.
Operation
Number
2185C4
Description
Transmission
Replacement
Number
Flat
Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part
Number
2WD BASE/TECH Inspect the ATF
warmer manufacture
date and check vehicle
for overheating and do
REPAIR
PROCEDURE D
06200-5J4-A71RM
12.7 hr
6ZF00
KG500
B17012K
06200-5J4-A71
06200-5J4-A81RM
12.7 hr
6ZF00
KG500
B17012L
06200-5J4-A71
-Replace engine,
transmission, radiator,
and hoses
-Flush heater core
- Includes updating
PCM/TCM, idle learn
and alignment
2185C4
2WD ADV - Inspect
the ATF warmer
manufacture date and
check vehicle for
overheating and do
REPAIR
PROCEDURE D
-Replace engine,
transmission, radiator,
and hoses
-Flush heater core
- Includes updating
PCM/TCM, idle learn
and alignment
Page 6 of 65
Inspection and REPAIR PROCEDURE D
2185C5
AWD BASE/TECH Inspect the ATF
warmer manufacture
date and check vehicle
for overheating and do
REPAIR
PROCEDURE D
06200-5L9-A72RM
13.1 hr
6ZF00
KG500
B17012M
06200-5J4-A71
06200-5L9-A81RM
13.1 hr
6ZF00
KG500
B17012N
06200-5J4-A71
-Replace engine,
transmission, radiator,
and hoses
-Flush heater core
- Includes updating
PCM/TCM, idle learn
and alignment
2185C5
AWD ADV - Inspect
the ATF warmer
manufacture date and
check vehicle for
overheating and do
REPAIR
PROCEDURE D
-Replace engine,
transmission, radiator,
and hoses
-Flush heater core
- Includes updating
PCM/TCM, idle learn
and alignment
Page 7 of 65
PARTS INFORMATION – WARMER INSPECT AND REPLACEMENT
Part Name
Part Number
Quantity
ATF Warmer Kit (Includes O-Rings)
06224-5J4-305
1
REQUIRED MATERIALS – ATF WARMER INSPECTION AND REPLACEMENT
Part Name
Part Number
Quantity
ATF Type 3.1
08200-9017
1
NOTE: 1 quart will fill 5 vehicles.
NOTE: Order the Honda ATF for this campaign.
PARTS INFORMATION – REPAIR PROCEDURE A
Part Name
Part Number
Quantity
Radiator (DENSO)
19010-5J2-A01
1
Reserve Tank
19101-5J2-A00
1
Reserve Tank Cap
19102-5J6-A00
1
Reserve Tank Joint
19106-RSA-G00
1
Reserve Tank Tube A
19103-5J2-A00
1
Reserve Tank Tube B
19104-5J2-A00
1
Water Hose (Lower) (A)
19502-5J2-A50
1
Water Hose (Lower) (B)
19504-5J2-A50
1
Water Hose (Upper)
19501-5J2-A00
1
Water Inlet Hose
79721-TZ3-A00
1
Water Outlet Hose Assembly
79725-TZ3-A00
1
Warmer Hose B (ATF)
19433-5J2-A00
1
Water Hose B
19522-R9P-A00
1
Water Hose C
19523-5J2-A00
1
Water Hose A
19521-5J2-A00
1
Warmer Hose A (ATF)
19432-5J2-A50
1
O-Ring (DENSO)
91307-RTA-005
2
Thermostat Cover Assembly
19315-5J2-A01
1
REQUIRED MATERIALS – REPAIR PROCEDURE A
Part Name
Part Number
Quantity
Coolant Type 2
OL999-9011A
16
Page 8 of 65
PARTS INFORMATION – REPAIR PROCEDURE B
Part Name
Part Number
Quantity
Cylinder Block Assembly
10002-5J2-A00
1
Cylinder Head Assembly (Front)
10004-R9P-A01
1
Cylinder Head Assembly (Rear)
10005-5J6-A00
1
Exhaust Pipe Gasket (ISHINO)
18212-SA7-003
2
Pre-Chamber Gasket
18393-SDB-A00
1
Self-Lock Nut (10 mm)
90212-SA5-003
9
Bolt (12 point 8 x 21 mm) (AWD Only)
90113-S10-000
8
Washer Bolt (10 x 30 mm) (AWD Only)
90382-SZA-003
2
Split Pin (3.0 x 22 mm)
94201-30220
2
Castle Nut (14 mm)
90363-S3V-A01
2
Spindle Nut (24 mm)
90305-SD4-003
2
Flange Nut (12 mm)
90371-SEF-000
4
Flange Bolt (10 x 35 mm)
90163-SDA-A01
1
Flange Bolt (10 x 45 mm)
90163-TZ3-A00
1
Flange Bolt (10 x 60 mm)
90168-TA1-A00
2
Flange Bolt (12 x 45 mm)
90165-SDA-A00
2
Flange Bolt (12 x 45 mm)
90164-T2G-A01
1
Flange Bolt (10 x 30 mm)
90163-SDB-A00
3
Flange Bolt (12 x 56 mm)
90170-TZ3-A00
4
Flange Bolt (10 x 50 mm)
95701-10050-08
4
Intake Manifold Cover Gasket (Upper)
17112-5G0-A01
1
Intake Manifold Gasket (NIPPON LEAKLESS)
17105-R9P-A01
1
Throttle Body Gasket
16176-RYE-A10
1
Fuel Joint Pipe Set (MSDS includes VOC)
16012-R9P-305
1
Front Intake Manifold Base Gasket
17055-R9P-A01
1
Rear Intake Manifold Base Gasket
17065-R9P-A01
1
Injector Seal Set
16453-R9P-A00
1
O-Ring
91311-5A2-A01
1
Exhaust Chamber Gasket (NIPPON LEAKLESS)
18115-5G0-A01
2
EGR Pipe Gasket A
18716-R70-A01
1
EGR Pipe Gasket B
18719-R70-A01
1
Page 9 of 65
Rear Cylinder Head Gasket (NIPPON LEAKLESS)
12261-R9P-A01
1
Front Cylinder Head Gasket (NIPPON LEAKLESS)
12251-R9P-A01
1
Timing Belt Idler Bolt
14551-RCA-A01
1
Front Water Passage Gasket (NIPPON LEAKLESS)
19411-5G0-A02
1
Rear Water Passage Gasket (NIPPON LEAKLESS)
19412-5G0-A01
1
O-Ring (Denso)
91307-RTA-005
Thermostat Cover Assembly
19315-5J2-A01
2
1
O-Ring (31.2 x 4.1 mm) (NOK)
91314-PH7-003
2
EGR Valve Gasket (ISHINO GASKET)
18715-PB2-000
1
Oil Filter
15400-PLM-A02
1
Radiator (DENSO)
19010-5J2-A01
1
Reserve Tank
19101-5J2-A00
1
Reserve Tank Cap
19102-5J6-A00
1
Reserve Tank Joint
19106-RSA-G00
1
Reserve Tank Tube A
19103-5J2-A00
1
Reserve Tank Tube B
19104-5J2-A00
1
Water Hose (Lower) (A)
19502-5J2-A50
1
Water Hose (Lower) (B)
19504-5J2-A50
1
Water Hose (Upper)
19501-5J2-A00
1
Water Inlet Hose
79721-TZ3-A00
1
Water Outlet Hose Assembly
79725-TZ3-A00
1
Warmer Hose B (ATF)
19433-5J2-A00
1
Water Hose B
19522-R9P-A00
1
Water Hose C
19523-5J2-A00
1
Water Hose A
19521-5J2-A00
1
Warmer Hose A (ATF)
19432-5J2-A50
1
Connecting Pipe
19505-5J2-A00
1
Water Passage
19410-5J2-A00
1
Flange Bolt (12 x 70 mm)
90051-R97-000
1
Flange Bolt (12 x 120 mm)
90051-5J4-000
1
Flange Bolt (10 x 30 mm)
90161-T2F-A01
3
Flange Bolt (10 x 45 mm)
90163-SZ3-000
3
Flange Bolt (14 x 135 mm)
90176-SDA-A00
2
Flange Bolt (10 x 77 mm)
90167-TZ7-A01
2
Flange Bolt (10 x 24 mm)
90166-TZ7-A01
2
Page 10 of 65
Flange Bolt (14 x 150 mm)
90177-SDA-A00
2
Bolt Washer (8 x 16 mm)
90101-SWA-A00
2
Flange Bolt (12 x 33 mm)
90186-SDA-A00
2
Flange Bolt (10 x 34 mm)
90162-T2A-A00
4
Snap Ring (32 x 2.2 mm)
44319-STX-A01
1
Set Ring (32 x 2.2 mm)
44319-STX-A60
1
Spindle Nut
90305-S3V-A11
2
Injector Clip
16451-5A2-A01
6
REQUIRED MATERIALS – REPAIR PROCEDURE B
Part Name
Part Number
Quantity
Coolant Type 2
OL999-9011A
3
Acura motor oil 0W-20
08798-9073
6
Page 11 of 65
PARTS INFORMATION - REPAIR PROCEDURE C
Part Name
Part Number
1
Transmission
2WD Base and Tech
Quantity
06200-5J4-A71RM
2WD Advanced
06200-5J4-A81RM
AWD Base and Tech
06200-5L9-A72RM
AWD Advanced
06200-5L9-A81RM
Flange Bolt (12 x 70 mm)
90051-R97-000
1
Flange Bolt (12 x 120 mm)
90051-5J4-000
1
Flange Nut (12 mm)
90371-SEF-000
4
Flange Bolt (10 x 35 mm)
Flange Bolt (10x 45 mm)
Flange Bolt (10 x 30 mm)
Flange Bolt (12 x 45 mm)
Flange Bolt (12 x 45 mm)
90163-SDA-A01
90163-TZ3-A00
90161-T2F-A01
90165-SDA-A00
90164-T2G-A01
1
1
3
2
1
Pre-Chamber Gasket
18393-SDB-A00
2
Exhaust Pipe Gasket (NOK)
18212-SA7-003
2
Self-Lock Nut (10 mm)
90212-SA5-003
9
Bolt (12 point 8 x 21 mm)
90113-S10-000
8
Washer Bolt (10 x 30 mm)
90382-SZA-003
2
Split Pin (3.0 x 22 mm)
94201-30220
2
Castle Nut (14 mm)
90363-S3V-A01
2
Flange Bolt (10 x 45 mm)
90163-SZ3-000
3
Flange Bolt (14 x 135 mm)
90176-SDA-A00
2
Flange Bolt (10 x 77 mm)
90167-TZ7-A01
2
Flange Bolt (10 x 24 mm)
90166-TZ7-A01
2
Flange Bolt (14 x 150 mm)
90177-SDA-A00
2
Flange Bolt (8 x 16 mm)
90101-SWA-A00
2
Flange Bolt (12 x 33 mm)
90186-SDA-A00
2
Flange Bolt (10 x 34 mm)
90162-T2A-A00
4
Snap Ring (32 x 2.2 mm)
44319-STX-A01
1
Set Ring (32 x 2.2 mm)
44319-STX-A60
1
Flange Bolt (10 x 30 mm)
90163-SDB-A00
3
Radiator (DENSO)
19010-5J2-A01
1
Reserve Tank
19101-5J2-A00
1
Reserve Tank Cap
19102-5J6-A00
1
Reserve Tank Joint
19106-RSA-G00
1
Reserve Tank Tube A
19103-5J2-A00
1
Reserve Tank Tube B
19104-5J2-A00
1
Water Hose (Lower) (A)
19502-5J2-A50
1
Page 12 of 65
Water Hose (Lower) (B)
19504-5J2-A50
1
Water Hose (Upper)
19501-5J2-A00
1
Water Inlet Hose
79721-TZ3-A00
1
Water Outlet Hose Assembly
79725-TZ3-A00
1
Warmer Hose B (ATF)
19433-5J2-A00
1
Water Hose B
19522-R9P-A00
1
Water Hose C
19523-5J2-A00
1
Water Hose A
19521-5J2-A00
1
Warmer Hose A (ATF)
19432-5J2-A50
1
O-Ring (DENSO)
91307-RTA-005
2
Thermostat Cover Assembly
19315-5J2-A01
1
Spindle Nut
90305-S3V-A11
2
REQUIRED MATERIALS – REPAIR PROCEDURE C
Part Name
Part Number
Quantity
ATF Type 3.1
08200-9017
1
OL999-9011A
12
NOTE: 1 quart will fill 5 vehicles.
Coolant Type 2
NOTE: Order the Honda ATF for this campaign.
Page 13 of 65
PARTS INFORMATION – REPAIR PROCEDURE D
Part Name
Part Number
1
Transmission
2WD Base and Tech
Quantity
06200-5J4-A71RM
2WD Advanced
06200-5J4-A81RM
AWD Base and Tech
06200-5L9-A72RM
AWD Advanced
06200-5L9-A81RM
Cylinder Block Assembly
10002-5J2-A00
1
Cylinder Head Assembly (Front)
10004-R9P-A01
1
Cylinder Head Assembly (Rear)
10005-5J6-A00
1
Exhaust Pipe Gasket (NOK)
18212-SA7-003
2
Pre-Chamber Gasket
18393-SDB-A00
1
Self-Lock Nut (10 mm)
90212-SA5-003
9
Bolt (12 point 8 x 21 mm) (AWD Only)
90113-S10-000
8
Washer Bolt (10 x 30 mm) (AWD Only)
90382-SZA-003
2
Split Pin (3.0 x 22 mm)
94201-30220
2
Castle Nut (14 mm)
90363-S3V-A01
2
Spindle Nut (24 mm)
90305-SD4-003
2
Flange Nut (12 mm)
90371-SEF-000
4
Flange Bolt (10 x 35 mm)
90163-SDA-A01
1
Flange Bolt (10 x 45 mm)
90163-TZ3-A00
1
Flange Bolt (10 x 60 mm)
90168-TA1-A00
2
Flange Bolt (12 x 45 mm)
90165-SDA-A00
2
Flange Bolt (12x 45 mm)
90164-T2G-A01
1
Flange Bolt (10 x 30 mm)
90163-SDB-A00
3
Flange Bolt (12 x 56 mm)
90170-TZ3-A00
4
Flange Bolt (10 x 50 mm)
95701-10050-08
4
Intake Manifold Cover Gasket (Upper)
17112-5G0-A01
1
Intake Manifold Gasket (Nippon Leakless)
17105-R9P-A01
1
Throttle Body Gasket
16176-RYE-A10
1
Fuel Joint Pipe Set (MSDS includes VOC)
16012-R9P-305
1
Front Intake Manifold Base Gasket
17055-R9P-A01
1
Rear Intake Manifold Base Gasket
17065-R9P-A01
1
Injector Seal Set
16453-R9P-A00
1
O-Ring
91311-5A2-A01
1
Page 14 of 65
Exhaust Chamber Gasket (Nippon Leakless)
18115-5G0-A01
2
EGR Pipe Gasket A
18716-R70-A01
1
EGR Pipe Gasket B
18719-R70-A01
1
Rear Cylinder Head Gasket (NIPPON LEAKLESS)
12261-R9P-A01
1
Front Cylinder Head Gasket (NIPPON LEAKLESS)
12251-R9P-A01
1
Timing Belt Idler Bolt
14551-RCA-A01
1
Front Water Passage Gasket (NIPPON LEAKLESS)
19411-5G0-A02
1
Rear Water Passage Gasket (NIPPON LEAKLESS)
19412-5G0-A01
1
O-Ring (Denso)
91307-RTA-005
Thermostat Cover Assembly
19315-5J2-A01
2
1
O-Ring (31.2 x 4.1 mm) (NOK)
91314-PH7-003
2
EGR Valve Gasket (ISHINO GASKET)
18715-PB2-000
1
Oil Filter
15400-PLM-A02
1
Radiator (DENSO)
19010-5J2-A01
1
Reserve Tank
19101-5J2-A00
1
Reserve Tank Cap
19102-5J6-A00
1
Reserve Tank Joint
19106-RSA-G00
1
Reserve Tank Tube A
19103-5J2-A00
1
Reserve Tank Tube B
19104-5J2-A00
1
Water Hose (Lower) (A)
19502-5J2-A50
1
Water Hose (Lower) (B)
19504-5J2-A50
1
Water Hose (Upper)
19501-5J2-A00
1
Water Inlet Hose
79721-TZ3-A00
1
Water Outlet Hose Assembly
79725-TZ3-A00
1
Warmer Hose B (ATF)
19433-5J2-A00
1
Water Hose B
19522-R9P-A00
1
Water Hose C
19523-5J2-A00
1
Water Hose A
19521-5J2-A00
1
Warmer Hose A (ATF)
19432-5J2-A50
1
Connecting Pipe
19505-5J2-A00
1
Water Passage
19410-5J2-A00
1
Flange Bolt (12 x 70 mm)
90051-R97-000
1
Flange Bolt (12 x 120 mm)
90051-5J4-000
1
Flange Bolt (10 x 30 mm)
90161-T2F-A01
3
Flange Bolt (10 x 45 mm)
90163-SZ3-000
3
Page 15 of 65
Flange Bolt (14 x 135 mm)
90176-SDA-A00
2
Flange Bolt (10 x 77 mm)
90167-TZ7-A01
2
Flange Bolt (10 x 24 mm)
90166-TZ7-A01
2
Flange Bolt (14 x 150 mm)
90177-SDA-A00
2
Bolt Washer (8 x 16 mm)
90101-SWA-A00
2
Flange Bolt (12 x 33 mm)
90186-SDA-A00
2
Flange Bolt (10 x 34 mm)
90162-T2A-A00
4
Snap Ring (32 x 2.2 mm)
44319-STX-A01
1
Set Ring (32 x 2.2 mm)
44319-STX-A60
1
Spindle Nut
90305-S3V-A11
2
Injector Clip
16451-5A2-A01
6
REQUIRED MATERIALS – REPAIR PROCEDURE D
Part Name
Part Number
Quantity
Coolant Type 2
OL999-9011A
3
Acura motor oil 0W-20
08798-9073
6
Page 16 of 65