TSBELE143

GROUP
ELE
MODEL
2016-2017MY
Optima (JFa)
NUMBER
143
DATE
February 2018
TECHNICAL SERVICE BULLETIN
SUBJECT:
SERVICE ACTION: OUTSIDE REAR COMBINATION
LAMP HARNESS REPLACEMENT (SA334)
This bulletin provides the procedure to replace the outside rear combination lamp harness on
some 2016-2017MY Optima (JFa) vehicles, produced from September 25, 2016 through March
16, 2017, which may exhibit an intermittent inoperative brake light with the possibility of a
“Check brake light” warning on the instrument cluster display. Follow the procedure outlined in
this bulletin to replace the outside rear combination lamp harness. Before conducting the
procedure, verify that the vehicle is included in the list of affected VINs.
 NOTICE
A Service Action is a repair program without customer notification that is performed
during the warranty period. Any dealer requesting to perform this repair outside the
warranty period will require DPSM approval.
Repair status for a VIN is provided on WebDCS (Service → Warranty Coverage →
Warranty Coverage Inquiry → Campaign Information). Not completed Recall / Service
Action reports are available on WebDCS (Consumer Affairs → Not Completed Recall
→ Recall VIN → Select Report), which includes a list of affected vehicles.
This issue number is SA334.
File Under: 
Circulate To:
X General Manager

X Service Advisors

X Technicians

X Service Manager

X Parts Manager

X Body Shop Manager 
X Fleet Repair

Page 2 of 4
SUBJECT:
SERVICE ACTION: OUTSIDE REAR COMBINATION
LAMP HARNESS REPLACEMENT (SA334)
Replacement Procedure:
1. Open the trunk, turn the cover knob (A)
(clockwise for left side, counter clockwise
for right side) and then carefully remove
cover (B).
Left rear combination lamp shown in images below
B
A
2.
Unplug the main outside lamp connector
(C) by pushing down on the lock and
pulling the connector outwards.
C
3.
Remove the four (4) retaining nuts and
remove the combination lamp assembly
from the vehicle.
TSB: SA334 Optima (JFa) February 2018
Page 3 of 4
SUBJECT:
4.
SERVICE ACTION: OUTSIDE REAR COMBINATION
LAMP HARNESS REPLACEMENT (SA334)
With the combination lamp uninstalled
from the vehicle, detach the main outside
lamp connector (D) from the tab and
disconnect the small connector (E).
5.
Uninstall the two bulb sockets and
remove the complete harness.
6.
Transfer the two bulbs (brake and turn
signal) from the old harness to the new
improved harness, and then reinstall the
harness in the reverse order of removal.
D
E
 NOTICE
If a brake lamp bulb is
inoperative, replace as necessary.
7.
Reinstall all removed components in the reverse order of removal.
Tightening Torque for nuts:
26 lb.in – 34 lb.in (2.94N.m – 3.92N.m, 0.3 – 0.4 kgf.m)
8.
Repeat steps 1-7 for the other side.
9.
Confirm proper operation of the combination lamps.
TSB: SA334 Optima (JFa) February 2018
Page 4 of 4
SERVICE ACTION: OUTSIDE REAR COMBINATION
LAMP HARNESS REPLACEMENT (SA334)
SUBJECT:
AFFECTED VEHICLE RANGE:
Model
Production Date Range
Optima (JFa)
September 25, 2016 through March 16, 2017
REQUIRED PART:
Part Name
Part Number
Figure
Outside Rear Combination
Lamp Harness
92480 D5000QQK
RELATED PART:
Part Name
Part Number
Brake Lamp Bulb
18644 21058L
Figure
NOTE: the (amber) turn signal bulb and/or tail lamp assembly should not be replaced unless
necessary.
WARRANTY INFORMATION:
N Code: N99 C Code: C99
Claim
Type
V
Causal P/N
92480 D5000
Qty.
0
Repair
Description
(SA334)
Outside Rear
Combination Lamp
Harness Replacement
(SA334)
Outside Rear
Combination Lamp
Harness Replacement
& One (1) Bulb
Replacement
(SA334)
Outside Rear
Combination Lamp
Harness Replacement
& Two (2) Bulb
Replacement
Labor Op
Code
Op
Time
Replacement
P/N
Qty.
170A64R0
0.3
M/H
92480 D5000QQK
2
92480 D5000QQK
2
170A64R1
0.3
M/H
18644 21058L
1
92480 D5000QQK
2
18644 21058L
2
170A64R2
0.3
M/H
 NOTICE
VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers
should reference SA334 when accessing the WebDCS system.
TSB: SA334 Optima (JFa) February 2018