IS-13169A
Service Bulletin Details
Public Details for: IS-13169A
This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
Models from 2016
| 2016 PREVOST H3-41 |
| 2016 PREVOST H3-45 |
| 2016 PREVOST H3-VIP |
| 2016 PREVOST X3 |
| 2016 PREVOST X3VIP |
Models from 2015
| 2015 PREVOST H3-41 |
| 2015 PREVOST H3-45 |
| 2015 PREVOST H3-VIP |
| 2015 PREVOST X3 |
| 2015 PREVOST X3VIP |
Models from 2014
| 2014 PREVOST H3-41 |
| 2014 PREVOST H3-45 |
| 2014 PREVOST H3-VIP |
| 2014 PREVOST X3 |
| 2014 PREVOST X3VIP |
Instruction Sheet IS-13169A PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT KIT REVISION A : THIS INSTRUCTION SHEET SUPERSEDES PREVIOUS VERSION. KIT IS13169-1 & IS13169-2 CANCELED, USE 145373 &145372 MATERIAL H3 SERIES – Kit # 145373 includes the following parts: Part No. Description Qty 145225 SUPPORT 1 564256 FLR20 ACB RADAR SENSOR 1 564257 STAND-OFF ADJUSTERS (kit of 3) 1 IS-13169 Instruction Sheet 1 FI-13169 Feuille d'instructions 1 X3 SERIES – Kit # 145372 includes the following parts: Part No. Description Qty 145207 SUPPORT 1 564256 FLR20 ACB RADAR SENSOR 1 564257 STAND-OFF ADJUSTERS (kit of 3) 1 IS-13169 Instruction Sheet 1 FI-13169 Feuille d'instructions 1 NOTE Material can be obtained through regular channels.IS-13169A Page 2 / 5 1) SUPPORT 2) STAND‐OFF ADJUSTERS 3) FLR20 ACB RADAR SENSOR FIG.1 : H3 SERIES - KIT # 145373 FIG.2 : X3 SERIES - KIT # 145372 CAUTION – STAND-OFF ADJUSTERS ARE NOT REUSABLE. DO NOT SEPARATE THE RADAR SENSOR FROM THE STAND-OFF ADJUSTERS IN ORDER TO REPLACE A DEFECTIVE RADAR SENSOR. INSTALL THE INCLUDED ASSEMBLY AS A COMPLETE UNIT. STAND-OFF ADJUSTOR ASSEMBLIES ARE PRE-ADJUSTED BEFORE DELIVERY IN ORDER TO RESPECT A PRECISE MEASUREMENT BETWEEN THE RADAR SENSOR AND THE SUPPORT, DO NOT SCREW, UNSCREW OR ALTER THE INITIAL POSITION OF THE STAND-OFFS ADJUSTMENT SCREW. DO NOT SEPARATE THE STAND-OFF CLIP FROM THE RADAR SENSOR RECEPTACLE. DOING SO WILL DAMAGE THE STAND-OFF CLIP. FIG.3 IS-13169A Page 3 / 5 PROCEDURE DANGER Park vehicle safely, apply parking brake, stop engine and set battery master switch(es) to the OFF position prior to working on the vehicle. IMPORTANT NOTES BEFORE PROCEEDING TO THE REPLACEMENT, MAKE SURE THAT THE BUMPER IS PROPERLY POSITIONED, IF NOT THE RADAR SENSOR AND ACB SYSTEM MAY OPERATE INPROPERLY. IF THE BUMPER SUFFERS DAMAGES AFTER A CHOCK AND IS IMPROPERLY POSITIONED, A REPOSITIONING OR ADJUSTMENT OF THE BUMPER WILL BE NECESSARY PRIOR PROCEEDING TO THE ALIGNMENT OF THE RADAR SENSOR. RADAR SENSOR ALIGNMENT IS DONE IN RELATION TO THE BUMPER, IF THE BUMPER POSITION IS NOT ADEQUATE, THE RADAR AND ACB SYSTEM MAY OPERATE INPROPERLY. IF THE BUMPER POSITION ADJUSTMENT IS DONE, THEN THE RADAR SENSOR ALIGNMENT PROCEDURE MUST BE DONE. X3 SERIES - RADAR SENSOR REPLACEMENT 1. Lower the reclining bumper. 2. Remove the radar sensor access panel (fig.4). FIG.4: X3 SERIES – RADAR SENSOR ACCESS PANEL FIG.5: X3 SERIES 3. Unscrew 4 mounting screws, remove the radar sensor support and disconnect the radar sensor harness (fig.5). Keep existing hardware for reuse. If needed, cut one or two nylon ties securing the harness to ease removal. 4. Plug radar sensor harness and install the new radar sensor and support assembly similarly as the previous installation. 5. Fix harness using nylon ties and existing tie mounts if applicable. 6. Radar sensor realignment might be necessary after installation. Refer to Maintenance Information MI14-34 for the complete procedure. This Web site under Technical Publications. document is available on Prevost IS-13169A Page 4 / 5 H3 SERIES - RADAR SENSOR REPLACEMENT 1. Lower the reclining bumper. 2. Unscrew 4 mounting screws, remove the radar sensor support and disconnect the radar sensor harness (fig.5). Keep existing hardware for reuse. If needed, cut one or two nylon ties securing the harness to ease removal. FIG.6: H3 SERIES FIG.7: H3 SERIES FIG.8: H3 SERIES 3. Plug radar sensor harness and install the new radar sensor and support assembly similarly as the previous installation. Make sure that the reference surfaces lean against the bumper structure and the notch in the radar support is at proper position (fig.7 & fig.8). 4. Fix harness using nylon ties and existing tie mounts if applicable. 5. Radar sensor realignment might be necessary after installation. Refer to Maintenance Information MI14-34 for the complete procedure. This Web site under Technical Publications. document is available on Prevost IS-13169A Page 5 / 5 PARTS / WASTE DISPOSAL Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal)