Prevost X3 2016

Vehicle Details: Recalls, Investigations, Decoded VIN Details, Service Bulletins

Below you will find all available information on the 2016 PREVOST X3, manufacturered by Volvo Group Canada, Inc.
The vehicle is described as a Other Bus Type.

ManufacturerKnown WMI(s)Fuel Type
PREVOST2P9001 2PC 4RK 2PC 2P9001 2P9110 2PC 2P9001 2P9001 2PC 4RK Diesel
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#

Sub-models: - X3-45 - X3-vip - X3-45 Vip - X3-45 Coach - X3-45 Commuter - X3 Passenger Coach - X3-45 Vip Entertainer - X3 Converted Coach Shell -

Frequently Asked Questions
  • Where is the 2016 PREVOST X3 produced?
     - The 2016 PREVOST X3 is produced in Ste-claire Quebec, Canada.
  • Are there recalls for the 2016 PREVOST X3?
     - There are 17 recall(s) for the 2016 PREVOST X3, additional information is below.
  • How much horsepower does the 2016 PREVOST X3 have?
     - The 2016 PREVOST X3 has 435 horsepower.
NHTSA Mandated Recalls
  • Recall 260233 [USA]: Beacons that do not provide proper illumination may be less visible to wheelchair lift users, increasing the risk of injury.

  • Recall 191777 [USA]: An overheated alternator bearing can increase the risk of a fire.

  • Recall 140674 [USA]: If the fire suppression system does not work as intended, it can increase the risk of injury in the event of a fire.

  • Recall 133695 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138361 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 122309 [USA]: If the fasteners loosen, the trailer hitch may deform or detach from the vehicle, increasing the risk of a crash.

  • Recall 125166 [USA]: The missing reflex reflectors may reduce the side visibility of the vehicle in certain conditions, increasing the risk of a crash.

  • Recall 122306 [USA]: If the fasteners loosen, the trailer hitch may deform or detach from the vehicle, increasing the risk of a crash.

  • Recall 114958 [USA]: A crack in the seat attachment could compromise the structural integrity of the seat, increasing the risk of passenger injury in the event of a crash.

  • Recall 109965 [USA]: Contact between the fuel line and the coolant line may cause a fuel leak and result in fuel spraying onto hot exhaust components increasing the risk of an engine compartment fire.

  • Recall 110405 [USA]: A wheel that turns unexpectedly may cause a loss of vehicle control and increase the risk of a crash.

  • Recall 2019084 [Canada]: Accessories

  • Recall 2017570 [Canada]: Accessories

  • Recall 2017476 [Canada]: Fuel supply

  • Recall 2016108 [Canada]: Fuel supply

  • Recall 2017570 [Canada]: Accessories

  • Recall 2017238 [Canada]: Accessories

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-19912E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision: e note added regarding power cable connection
  • IS-19901E - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision: e note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-901 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : X3 series envirocare - ions air sanitizer
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS22-040 - EQUIPMENT ADAPTIVE/MOBILITY: Brake pedal seal plate installation kit
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • IS-21901 - EQUIPMENT: X3 series envirocare - ions air sanitizer
  • IS-19912D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - x3 series us10 up to ghg17 cooling system
  • IS-19901D - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • IS-19901C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system
  • IS-19912C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • VBC-PREVOST 4 - EQUIPMENT ADAPTIVE/MOBILITY:VEHICLE CONTROLS:BRAKING: Communication letter from accociate administration for enforcement, nhtsa from prevost subject vehicle brand: prevost (ewr#000650)
  • VBC-PREVOST 3 - EQUIPMENT ADAPTIVE/MOBILITY:WHEELCHAIR LIFT/RAMP:CONTROLS/CONTROL WIRING: Wheeflchair lift cable wear - on the vehicles affected by this bulletin, it is possible to have premature wear of the wcl power cable caused by friction against the access panel,
  • VBC-PREVOST 2 - EQUIPMENT ADAPTIVE/MOBILITY: Bendix m-32qr abs modulator valve replaced by new m-40qr valve.
  • SP21-300 - EQUIPMENT: Automatic fire suppression system - tamper seal replacement
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • WB16-02D - BACK OVER PREVENTION:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system. The corrective measures of this bulletin are very important and must all be c
  • SP17-301 - EQUIPMENT: On the vehicles affected by this bulletin, replace the ahi dozer by an improved part preventing nozzle clogging.
  • SP16-322C - WHEELS: On the vehicles affected by this bulletin, replace the front axle wheel hub bearing unit with an improved version.
  • MI16-17D - SEATS: Use this procedure for the removal and installation of the twin bosch hd10 (120a or 150a) alternators.
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-20007A - VISIBILITY: Driver⿿s air condenser replacement and relocation revision: a material: added hardware.
  • IS-13169A - BACK OVER PREVENTION: SENSING SYSTEM: RADAR: Prevost aware adaptive cruise braking (acb) flr20 radar sensor replacement kit revision a: kit is13169-1 & is13169-2 canceled, use 145373 &145372
  • IS-20929 - EQUIPMENT: Uv lights installation in ac compartment
  • IS-20929 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Uv lights installation in a/c compartment
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20007 - EQUIPMENT: Driver's air condenser replacement and relocation x3-45vip from e-5459 to h-6179 retrofitted with efd
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI18-18B - EQUIPMENT: General hoisting and towing procedures revision: b updated 2.1 to show rubber chocks, secure front and rear.
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-19901B - EQUIPMENT: Electric fan drive cooling system conversion with bosch alternator revision b: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19912B - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision : b parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20907 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass panel behind driver x3
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • IS-19084 - EQUIPMENT: Accessory air filter replacement replaces 642192
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P105998 - POWER TRAIN: Repair instructions to address fault codes P105998 gearbox oil temperature sensor - component orsystem over temperature
  • P054415 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P054415 exhaust gas temperature sensor bank 1 sensor 1 - circuit short to battery or open
  • P052400 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P052400 engine oil pressure too low
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-20905 - EQUIPMENT: Hand sanitizer dispenser installation
  • IS-19912A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - mention added stating to disable ⿿prime⿝; parts added in the kit.
  • IS-19901A - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with bosch alternator - x3 series us10 up to ghg17 cooling system - mention added stating to disable ⿿prime⿝; parts added in the kit
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-19901A - ENGINE AND ENGINE COOLING: Revision : mention added stating to disable prime & parts added in the kit.
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19040A - STEERING: This instruction sheet explains how to replace power steering pump discharge hose (pressure) - #161335p or #160039
  • SP19-301 - EQUIPMENT: On the vehicles affected by this bulletin, the compressor & radiator door lower hinges must be replaced by new stainless steel units
  • sp19-304 - LATCHES/LOCKS/LINKAGES: On the vehicles affected by this bulletin, the t-key cylinder lock must be disassembled and lubricated, the latch pin inspected for damage and replaced as required. The upper and lower door stops must also be inspected if found broken or mi
  • IS-19912 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system conversion kit (with delco remy alternators) on x3 vehicles equipped with us10 up to ghg17 engine.
  • IS-19901 - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric cooling system with bosch alternators on x3 series vehicles equipped with us10 up to ghg17 engines;
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • WB19-14 - ELECTRICAL SYSTEM: Neutral gear - software update
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • Mi14-34D - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) - flr20 & flr21 radar sensor alignment
  • IS-19922 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) flr10 to flr21 radar sensor upgrade
  • IS-19915 - EQUIPMENT: Mp-1000 multimedia player installation
  • IS-19040 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: Power steering pump discharge hose (pressure) replacement
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • IS-19909D - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • IS-19040 - STEERING: This instruction sheet explains how to perform the replacement of the power steering pump discharge hose (pressure) #161335p or #160039, using kit #160127;
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-19909A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • MI19-06 - BRAKES (PWS): This maintenance information is published to answer some questions regarding the inverted or ?Trailing? Mounting position of the drive axle brake calipers on prevost vehicles
  • MI19-05 - EQUIPMENT: This maintenance information expains how to adjust p/n 660865, 660699 draglinks
  • IS-19909 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on x3 vehicles
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • Wb17-14B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
  • IS-18907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install hatches with fan on x3 vehicles.
  • SP18-307 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, the bitzer compressor shaft seal must be replaced. Additionally, the compressor oil must be renewed and the oil quantity increased by 10oz (300ml).
  • Sp18-302 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, install a pressure switch into the front service compartment to send a faster signal to the allison transmission to switch to neutral at stop.
  • SP18-306 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • WB18-04 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available.
  • MI18-37 - POWER TRAIN:AUTOMATIC TRANSMISSION: This maintenance information presents information about the removal or installation of the lang kk73.1 electromagnetic clutch - part of the bitzer (model 4nfcy) air conditioning compressor.
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-18A - EQUIPMENT: This maintenance information explains how to tow and hoist prevost vehicles.
  • MI18-05 - ENGINE AND ENGINE COOLING: This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • MI14-40B - ENGINE AND ENGINE COOLING: This maintenance information presents how to install and remove the bosch hd10 alternator
  • WB18-01A - STRUCTURE: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • WB16-02H - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • WB18-07B - EQUIPMENT: On the vehicles affected by this bulletin, the busbar connected to circuit breaker cb13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper inst
  • Sp18-304A - EQUIPMENT:MECHANICAL: For vehicles affected by this bulletin, on the wheelchair area sliding door, install a new upper roller carrier, adjust the door and inspect all fasteners.
  • Sp18-303 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, the condenser compartment wall may present fatigue cracks on or near the a/c receiver tank support. Follow these instructions to repair and improve the support.
  • Sp18-301 - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY: On the vehicles affected by this bulletin, the existing surge tank support has to be replaced by a new configuration including two supports. That will allow a better distribution of the load between the tank and the support.
  • MI18-18 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: This maintenance information explains how to tow and hoist prevost vehicles.
  • SP17-314-R13 - INTERIOR LIGHTING: This bulletin explains how to install a light at the entrance door.
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • IS-18902 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to installa parcel rack door kits
  • WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB15-19H - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This bulletin explains how to add a reinforcement bracket to bitzer a/c compressor to increase the installation stiffness and reduce vibration amplitude.
  • SP17-314 - INTERIOR LIGHTING: This bulletin explains how to install a light at the entrance door.
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • SP15-340B - STEERING: On the vehicles affected by this bulletin, replace the hardware on the sway bar clamps of the steer and drive axles.
  • SP15-343D - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: On the vehicles affected by this bulletin, replace the hardware on the sliding door of the wheelchair seating area.
  • IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
  • SP15-349 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, one of the 100 amp vanner battery equalizer may have been incorrectly programmed and must be replaced.
  • WB15-53A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles covered by this bulletin, two dpf (diesel particulate filter) plugs may be loose. If a plug is loose, it may fall out under the effect of vibration. This may cause leakage of hot exhaust gases. It is therefore necessary to c
  • SP15-343B - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, replace the hardware on the sliding door of the wheelchair seating area.
  • IS-15012 CO24 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to install a "t" key on curbside engine compartment door
  • SP15-340 - STEERING: On the vehicles affected by this bulletin, replace the hardware on the sway bar clamps of the steer and drive axles.
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • SP15-327 - POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES: On the vehicles affected by this bulletin, inspect the coolant hose flexible elbow and piping arrangement on the transmission cooler.
  • IS-13169A - BRAKES (PWS): This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • SP17-314 - INTERIOR LIGHTING: On the vehicles affected by this bulletin, install a light at the entrance door.
  • SP17-313 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version and disa
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • IS-17016 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruciton sheet explains how to relocate the rv-3 valve
  • Wb18-01 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH: On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
  • Sp18-300 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: This bulletin explains how to replace ceiling transition pannels, when needed
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • MI14-40A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance inforamtion presents how to install and remove the bosch hd10 alternator
  • Wb15-19F - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • SP16-304 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, replace the battery connection decal by a new version.
  • MI16-07 - ENGINE AND ENGINE COOLING: Prevost is now offering a clutch replacement kit for vehicles equipped with a kendrion (linnig) llw203 series fan clutch and gearbox assembly. This kit will allow the replacement of the clutch alone, without the need to purchase a complete
  • IS-14154 - FUEL SYSTEM, GASOLINE: This instruction sheet explains how to modify the support beam (part # 30022 installation)- as part of the x3 fuel tank installation
  • MI16-06 - ENGINE AND ENGINE COOLING: This maintenance information shares information about a new automatic control mode now available on prevost vehicles equipped with the volvo engine brake (veb).
  • WB17-02 - ENGINE AND ENGINE COOLING: This bulletin explains how install an extension to the linear thermal detector (ltd) over the alternators
  • SP17-307 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: This bulletin explains how to replace the radiator door upper hinge
  • SP17-303D - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace two idlers by an improved version on the alternator drive belt and on the a/c belts.
  • IS-16048 - LATCHES/LOCKS/LINKAGES: This instruction sheet explains how to install a wcl manual lock
  • CK17-30 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is now possible to replace the older generation tgw 2.0 (3g network) by the newer 2.1 version (4g the network) using accessory kit 23266301 and the following procedure.
  • Sp16-323 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, change a parameter in the mux system to deactivate a dtc corresponding to air dryer cartridge change warning.
  • MI16-32 - POWER TRAIN:DRIVELINE:CENTER SUPPORT BEARING: Explains that improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • WB15-19 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP15-318 - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: On the vehicles affected by this bulletin, replace the battery box decals.
  • MI15-40A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information offers an overview of the operation of commuter bi-part doors.
  • WB15-06D - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, inspect the serial number of the current sensors in the battery compartment and follow instructions to perform replacement if applicable. A number of sensors have been identified by the manufacture
  • Sp17-312A - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • SP16-43A - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
  • SP16-326 - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
  • SP16-311B - EXTERIOR LIGHTING: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • WB16-02B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • Sp16-309A - ENGINE (PWS): On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
  • Sp16-303C - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, reposition the harness out of the path of an unlocked electrical box door.
  • Sp16-300C - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, improvement of a charge air cooler tube support is required.
  • Sp16-317 - BRAKES (PWS): On the vehicles affected by this bulletin, it is necessary to ensure proper brake pedal installation and adjustment following the procedure below.
  • IS-16902 - BRAKES (PWS): This instruction sheet explains how to install and adjust brake pedal kit is16902
  • MI16-14 - SUSPENSION: Use this procedure when a suspension height check or adjustment must be performed.
  • Mi16-28 - VISIBILITY:REARVIEW MIRRORS/DEVICES: This maintenance information explains that on vehicles equipped with ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a dri
  • WB16-02 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • SP16-306A - WHEELS: On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
  • Sp16-302A - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK ASSEMBLY: On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
  • MI16-27 - WHEELS: On vehicles operating in muddy road conditions, a road material ring may accumulate and harden inside the tag axle wheel. Depending on the hardness and abrasion potential of the dirt road material, the caliper body wall may wear out and thi
  • Sp16-313A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
  • Sp16-311A - EQUIPMENT: On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
  • Sp16-26 - ENGINE (PWS): On the vehicles affected by this bulletin, an additional decal should be affixed to the engine compartment. Perform the addition to comply with title 13, california code of regulations, section 1956.8.
  • Sp16-303B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, reposition the harness out of the path of an unlocked electrical box door.
  • SP16-306 - WHEELS: On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
  • MI16-23 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information explains that decals are available to update the front junction box on 2013 to 2016 prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of t
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • MI16-10 - WHEELS: This information letter applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a specifi
  • Sp16-309 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
  • SP16-300B - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, improvement of a charge air cooler tube support is required.
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • MI16-12 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information explains how to perform the replacement of glued fixed thermos window. This procedure may also be used for the replacement of non-thermos fixed window as the installation method is similar.
  • SP16-303 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, reposition the harness out of the path of an unlocked electrical box door.
  • WB15-55 - POWER TRAIN:AXLE ASSEMBLY: On the vehicles affected by this bulletin, inspect the gap between the radius rod support and the front axle. A deviation in the axle beam envelope can lead to interference between the two parts. In most cases, slightly moving the support w
  • SP16-302 - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
  • WB16-04 - STEERING: On the vehicles affected by this bulletin the steering damping cylinder rod end spherical bearing may be loose in its housing. Replace as required and secure the steering damper spherical bearing with the provided hardware.
  • MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
  • Sp17-313 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version.
  • CK17-26 - ENGINE (PWS): On the vehicles affected by this bulletin, it is now possible to disable the engine brake automatic function by running accessory kit # 23181730.
  • SP15-341C - ELECTRICAL SYSTEM:HORN: On the vehicles affected by this bulletin, replace the horn support by 140034.
  • WB15-19E - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP17-23 - ELECTRICAL SYSTEM: On the vehicles affected by the bulletin, there is a possibility for the connection of the 12-24 volt power sensor to be reversed in the rear electrical box.
  • SP16-311G - EXTERIOR LIGHTING: On the vehicles affected by this bulletin, add z clips to secure the direct light lenses, 13 lenses per vehicle.
  • Wb17-14A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
  • sp17-310 - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, it is necessary to replace the two engine door latch pins and the compressor door latch pin by new units made of sturdier material.
  • Sp17-312 - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
  • Sp17-311 - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, replace connector c12 installed inside the dpf access door with an improved version providing a better seal.
  • IS-15113 - STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS: This instruction sheet explains how to proceed to the 7 pivots luggage door hinge replacement
  • WB16-02C - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system. The corrective measures of this bulletin are very important and must all be ca
  • MI16-10A - WHEELS: This maintenance information applies only to vehicles equipped with 19000 lb independent front suspension (ifs) and 22.5 x 10.5 alcoa aluminum wheels for 365/70 r 22.5 size tires. When balancing this wheel for installation on the ifs, a spe
  • IS-13169 - FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL: This instruction sheet explains how to install the aware adaptive cruise braking (acb) flr20 radar sensor replacement kits # 145372 and 145373
  • Sp16-320 - STRUCTURE:BODY:DOOR: On the vehicles affected by this bulletin, the compressor door support to the vehicle must be improved by the addition of a lower support bracket and the replacement of the two door hinges. A support plate must also be riveted to the door
  • WB16-02E - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, it is necessary to perform a multiplex software update plus other corrective measures to improve the charging system.
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
  • Sp16-326B - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
  • WB17-06 - EQUIPMENT:MECHANICAL: On the vehicles affected by this bulletin, replace the existing wheelchair lift control pendant support by an improved version.
  • WB15-19G - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP16-321 - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, proceed to the replacement of the original a/c tensioner and alternator idler bearings with a fag branded unit. These fag bearings are of heavier duty construction and will offer extended durabili
  • SP16-319B - EQUIPMENT ADAPTIVE/MOBILITY: On the vehicles affected by this bulletin, replace the pitman arm nut and re-torque to specification.
  • SP16-318 - STRUCTURE:BODY:DOOR: Explains how to adjust the sliding door of the wheelchair seating area.
  • SP16-314 - EQUIPMENT: On the vehicles affected by this bulletin, add dampers to the driver's sunshades guides to ease the end course on sunshade retract.
  • MI16-34 - ELECTRICAL SYSTEM: "this maintenance information describes the steps to be followed on your computer to add the volvo engine brake auto mode on the vehicle. The auto mode may be added on us10 and obd13 vehicles that were built before the introduction of the
  • SP16-312 - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, replace the pitman arm nut and re-torque to specification.
  • MI16-17B - ELECTRICAL SYSTEM: On the vehicles affected by this bulletin, secure and adjust the two vehicle tlse element connections using material and procedure outlined below.
  • MI46-06 - ENGINE (PWS): New auto engine brake volvo engine brake (veb) with automatic control mode a new automatic control mode is now available on prevost vehicles equipped with the volvo engine brake (veb), when running in auto mode (which is the default mod
  • SP16-303 - EQUIPMENT:MECHANICAL:WRECKER AND WHEEL LIFT DEVICES: On the vehicles affected by this bulletin, it is possible to have premature wear of the wcl power cable caused by friction against the access panel.
  • WB15-55 - STEERING:LINKAGES:TIE ROD ASSEMBLY: Radius rod support and i-beam axle gap inspection on the vehicles affected by this bulletin, inspect the gap between the radius rod support and the axle. A deviation in the axle beam envelope can lead to interference between the two part
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) opened a preliminary evaluation after reviewing field reports concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable.Analysis of the data provided by prevost car (us) inc. Showed high failure frequency and thermal events. An immediate shutdown of the bus can increase the risk of a crash or injury of bus occupants. In response to this investigation, prevost car (us) inc. And volvo bus corporation decided to conduct recalls 22v-221 and 22v-222. By submitting part 573 defect information reports on april 6, 2022, prevost car (us) inc. And volvo bus corporation notified odi of a safety defect in certain model year (my) 2010-2023 prevost h3-45; x3-45; x3-45 com; h3-45 vip: x3-45 vip and 2020 volvo 9700 vehicles; some of these buses may have experienced thermal events after failure of the alternator front bearing, because the alternator belt continues to turn the alternator after the bearing failure.These recall actions address the safety concern that led to the opening of this investigation.Therefore, with these recall actions, this investigation is closed. The recalls encompass all model and my vehicles addressed by the investigation. However, the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist in other model or my vehicles outside of the recall scope. The agency reserves the right to take further action if warranted by the circumstances.

NHTSA decoded information from VIN

1 Results returned successfully. NOTE: Any missing decoded values should be interpreted as NHTSA does not have data on the specific variable. Missing value should NOT be interpreted as an indication that a feature or technology is unavailable for a vehicle.

Variable Value
Body ClassIncomplete - Bus Chassis
Brake System DescPneumatic system
Brake System TypeAir
Bus Length45
Bus TypeEntertainer Coach
DisplacementCC12800.0
DisplacementCI781.10392441257
DisplacementL12.8
Engine ConfigurationIn-Line
Engine Cylinders6
EngineHP435
EngineHP_to500
EngineKW324.3795
Engine ManufacturerVolvo
Engine ModelD13
Error Text0 - VIN decoded clean. Check Digit (9th position) is correct
Fuel Type PrimaryDiesel
MakePREVOST
MakeID4148
ManufacturerVOLVO GROUP CANADA, INC
Manufacturer Id13545
ModelX3 Converted Coach Shell
ModelID28636
Model Year2016
NCSA Body TypeOther Bus Type
NCSA MakeOther Make
NCSA ModelBus: Rear engine, Flat front
Other Bus InfoIntegral Structure
Plant CitySTE-CLAIRE
Plant CountryCANADA
Plant StateQUEBEC
SeriesX3-45 V.I.P. Entertainer
VIN2PCC33499GC735979
Vehicle Descriptor2PCC3349*GC
Vehicle TypeBUS
Latest VINs Decoded for this Manufacturer
VIN Year Model Manufactured In
2PCCS3496GC7359572016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCC33499GC7359792016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3492GC7360062016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3493GC7360012016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3498GC7359302016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3498GC7359582016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3491GC736002016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3493GC7359502016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3490GC7360222016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCC33497GC7359952016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCC33495GC7360312016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCC33496GC7359552016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3490GC7360672016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3496GC7359882016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3492GC7359412016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3496GC7360082016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3499GC7360042016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3496GC7359602016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS349XGC7360302016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCC33494GC7359542016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3491GC7360142016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCCS3492GC7360232016X3 Converted Coach ShellSTE-CLAIRE QUEBEC, CANADA
2PCG33494GC7360372016X3 Passenger CoachSTE-CLAIRE QUEBEC, CANADA
2PCG33499GC7360792016X3 Passenger CoachSTE-CLAIRE QUEBEC, CANADA

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.