SCI19-01C
Service Bulletin Details
Public Details for: SCI19-01C
The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
- 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 -
Models from 2018
2018 PREVOST H3-41 |
2018 PREVOST H3-45 |
2018 PREVOST X3 |
Models from 2017
2017 PREVOST H3-41 |
2017 PREVOST H3-45 |
2017 PREVOST X3 |
Models from 2016
2016 PREVOST H3-41 |
2016 PREVOST H3-45 |
2016 PREVOST X3 |
Models from 2015
2015 PREVOST H3-41 |
2015 PREVOST H3-45 |
2015 PREVOST X3 |
Models from 2014
2014 PREVOST H3-41 |
2014 PREVOST H3-45 |
2014 PREVOST X3 |
Models from 2013
2013 PREVOST H3-41 |
2013 PREVOST H3-45 |
2013 PREVOST X3 |
Models from 2012
2012 PREVOST H3-41 |
2012 PREVOST H3-45 |
2012 PREVOST X3 |
Models from 2011
2011 PREVOST H3-41 |
2011 PREVOST H3-45 |
2011 PREVOST X3 |
SERVICE CENTER INFORMATION i DATE : SUBJECT : SCI19-01C September 2019 SECTION : 00 GENERAL MCM MODULE P/N 23499009 BENCH PROGRAMMING PROCEDURE FOR THE ELECTRIC FAN DRIVE CONVERSION KIT Addition of the following special tools: harness #0610162 & power supply #0610163 Revision: C 09-11-19 DESCRIPTION The intent of this procedure is to guide you through the steps required to program a MCM especially for the control of the electric fan drive as required for conversion kit of instruction sheets IS-19900, IS-19901, IS19910, IS-19912. BEFORE PROGRAMMING AFTER PROGRAMMING MCM (non-programmed) part #23499009 MCM programmed part #23499009-EFD MATERIAL NEEDED Part No. Description Qty 23499009 MCM (non-programmed) 1 7770985 DECAL 1 SPECIAL TOOLS AND OTHER EQUIPMENT NEEDED 1. 2. 3. 4. 5. 6. EL A laptop with the following software installed: MAIDCOM. A network access Interface harness #0610162 Special Prevost cable #066009 24V-3A Power supply #0610163 Electric fan control program: body software FB06100118F01SCI19-01C Page 2 / 13 INSTALLING MAIDCOM 1. Install Maidcom on your computer. Get Maidcom on Volvo network using the link below: https://secure.volvo.com/VBCRemote/files_Applications/MAIDCOM%20Standalone/Setup.Maidcom2_7_ 5591_Standalone.zip 2. You will end up here. Type your username and current password. 3. This dialog box will show. Select “Open”. 4. A window similar to the one below will show. Double-click on the file to run the Setup Wizard and perform the installation steps. EL SCI19-01C Page 3 / 13 5. Maidcom now installed on your computer. EL SCI19-01C Page 4 / 13 6. Make a new icon in your taskbar so you can start Maidcom from the taskbar. To do so, in the Start Menu, right-click on M2 Maidcom2 and then select Pin to Taskbar. NEW LINK ON YOUR COMPUTER Important note for computers equipped with Windows 10. Make sure that Internet Explorer is installed on your computer and that you use it to create the link and to connect with the MCM module. Edge fails to connect with the MCM module. Don’t use Edge for this procedure. 7. You need to create one shortcut (Internet Explorer link) on your desktop as seen on the image below. EL SCI19-01C Page 5 / 13 8. Create the link with the following addresses: Name: Volvo Bus Local Host http://localhost:49555/ GET BODY SOFTWARE AND SAVE ON YOUR COMPUTER 9. Get the MCM program for US10 to GHG17 (body software FB06100118F01) on the Service Tips portal using the link below and save it on your computer. http://teamplace.volvo.com/sites/vbc-scr-dtr-service/Service tips/Electric Fan drive service kit/Body Software 10. Click on FB06100118F01 and then save it on your computer at an appropriate location. You can save file to your Desktop, which can give you quick access to it. EL SCI19-01C Page 6 / 13 CONNECTIONS 11. Connect the interface harness #0610162 to the non-programmed MCM. 12. Connect harness #066009 to the COM serial port of your computer. #066009 13. Connect the other end of harness #066009 to the DB9 connector on the interface harness #0610162. 14. Connect the 24V power supply #0610163 to the appropriate connector on the interface harness. START MAIDCOM 15. Click the Maidcom icon to start it. Maicom will try to connect with the MCM module. EL SCI19-01C Page 7 / 13 There is a good chance that the first connection trial fails. If this is the case, in the taskbar, right-click the Maidcom icon and then select Auto-Detect. EL SCI19-01C Page 8 / 13 EL SCI19-01C Page 9 / 13 CONNECTING WITH THE MCM WEB PAGE 16. Connect with the MCM web page using the Volvo Bus Local Host link previously made. 17. Make sure to use Internet Explorer . Use the following user name & password: User name: Password: 20. Once connected, select Download Software Package. EL SCI19-01C Page 10 / 13 21. Click on Browse and search for the Body Software saved on your computer (see 1 on image below). 22. Select the Body Software FB0610011801 (see 2 on image below). 23. Click on Download (see 3 on image below). 24. Click on Start System Software and then….wait EL . SCI19-01C Page 11 / 13 25. The following window is normal, ….wait 26. The following window is normal ….wait until the window closes. CONFIRM THAT THE MCM WAS PROGRAMMED SUCCESSFULLY 27. Confirm that the MCM was programed successfully. Select Vehicle Information. EL SCI19-01C Page 12 / 13 28. Exit Maidcom. To do so, right-click on the icon and then select Disconnect. DECAL 29. Identify the now programed MCM. Programed MCM for the Electric Fan Drive conversion kit is part number 23499009-EFD. Affix decal #7770985 on the programed MCM. To avoid any confusion, hide the MCM previous part number 23499009 with the decal. EL SCI19-01C Page 13 / 13 EL