Prevost H3-41 2013

Vehicle Details: Recalls, Investigations, Service Bulletins

Below you will find all available information on the 2013 PREVOST H3-41.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#

Sub-models: - H3-41 Coach -

Frequently Asked Questions
  • Are there recalls for the 2013 PREVOST H3-41?
     - There are 13 recall(s) for the 2013 PREVOST H3-41, additional information is below.
NHTSA Mandated Recalls
  • Recall 133681 [USA]: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

  • Recall 138344 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 109921 [USA]: Contact between the fuel line and the coolant line may cause a fuel leak and result in fuel spraying onto hot exhaust components increasing the risk of an engine compartment fire.

  • Recall 114519 [USA]: The damaged wires may activate the afss and shutdown the engine, increasing the risk of a vehicle crash.

  • Recall 101799 [USA]: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.

  • Recall 100622 [USA]: Without functioning windshield wipers, the driver's visibility may be reduced, increasing the risk of a crash.

  • Recall 94504 [USA]: This contact may cause the turnbuckle to fracture without warning. if the drag link turnbuckle breaks while the vehicle is in use, stability and vehicle control may be lost, increasing the risk of a crash.

  • Recall 93746 [USA]: Uncontrollable throttle position may lead to a loss of vehicle control, increasing the risk of a crash.

  • Recall 95641 [USA]: An activation of the afss causes the vehicle to come to an unplanned stop. this could increase the risk of a vehicle crash or personal injury.

  • Recall 2015240 [Canada]: Accessories

  • Recall 2013139 [Canada]: Steering

  • Recall 2013059 [Canada]: Other

  • Recall 2013014 [Canada]: Other

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-22106 - EQUIPMENT: H3 lavatory fan retrofit kit
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-19910i - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with delco remy alternator. Revision : i note added regarding power cable connection
  • IS-19900J - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator. Revision : j - note added regarding power cable connection
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • IS-22902 - WHEELS: Tag axle hub flange - alternate cap screw
  • IS21-072 - ELECTRICAL SYSTEM: Steering gateway, revision a : cancel watch dog removal from efd part of the instruction
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS20-932A - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • MI18-16B - ELECTRICAL SYSTEM: Bosch hd10 alternator diagnostic guide revision b to avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
  • MI21-06 - FUEL SYSTEM, DIESEL: Diesel exhaust fluid ( def ) contamination in fuel system, inspection and repair ⿿ from us10 to newer engine generation
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • is_20089 - LATCHES/LOCKS/LINKAGES: Lavatory compartment sliding door latch improvement
  • IS-18042 - ELECTRICAL SYSTEM: Eberspacher preheater installation in replacement of spheros & valeo preheaters
  • IS-08080B - EQUIPMENT: Sound selector replacement, vss04 to vss05; when replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • IS-20932A - EQUIPMENT: H3 series envirocare - ions air sanitizer rev a
  • IS-20932 - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS-20025A - VEHICLE SPEED CONTROL:CRUISE CONTROL: Prevost aware adaptive cruise braking (acb) ⿿ flr10 to flr21 radar sensor upgrade applicable to: h3 series vehicles equipped with acb system flr10 radar sensor
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI21-01 - EQUIPMENT: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI21-01 - POWER TRAIN: Volvo i-shift transmission replacement - difference between connections at the top of the oil filter housing
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI02-17A - EQUIPMENT ADAPTIVE/MOBILITY: Revision : a torque value reduced
  • IS-14145 - ELECTRICAL SYSTEM: This instruction sheet explains how to add sunshade switches on the dashboard
  • MI16-17D - SEATS: Use this procedure for the removal and installation of the twin bosch hd10 (120a or 150a) alternators.
  • MI18-02A - ENGINE AND ENGINE COOLING: Engine oil & filter change intervals - volvo d13 engine, from us10 revision: a updated for obd20 engines
  • IS-19165A - ELECTRICAL SYSTEM: Lavatory fan retrofit kit applicable for h3 series coaches from r-1012 (1994) revision a: added installation detail at step 8
  • IS-20923 - EQUIPMENT: H3 driver⿿s partition lite installation
  • P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • U17_P040200 - ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL: Engine exhaust gas recirculation differential pressure - mechanical system not responding properly us13 ⿿ us20 emissions
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-09900i - EQUIPMENT ADAPTIVE/MOBILITY: Electric fan drive cooling system conversion with bosch alternator revision i: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal, st,16
  • IS-19910H - ENGINE (PWS): Electric fan drive cooling system conversion with delco remy alternator revision h: parts obsolete: 050303, 391028, 562112 replaced by: 830165 24v red telltale light module qty: 1x 381594 bracket, telltale qty:1x 561540 tab terminal,
  • IS-20906 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass shield behind driver h3 series
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT: Prevost vehicle disinfection procedure revision a
  • U17_P040200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • U02A200 - ELECTRICAL SYSTEM: Repair instructions to address fault codes U02A200 lost communication with reductant quality module
  • U029E00 - ENGINE (PWS): Repair instructions to address fault codes U029E00 lost communication with nox sensor "b"
  • U029D00 - ENGINE (PWS): Repair instructions to address fault codes U029D00 lost communication with nox sensor "a"
  • P256000 - EQUIPMENT: Repair instructions to address fault codes P256000 engine coolant level low
  • P242A15 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P242A15 exhaust gas temperature sensor bank 1 sensor 3 - circuit short to battery or open
  • P20E892 - EQUIPMENT: Repair instructions to address fault codes P20E892 reductant pressure too low - performance orincorrect operation
  • P208464 - EQUIPMENT: Repair instructions to address fault codes P208464 exhaust gas temperature sensor circuit range/performance bank 1 sensor 2 - signal plausibility failure
  • P204A13 - EQUIPMENT: Repair instructions to address fault codes P204A13 reductant pressure sensor - circuit open
  • P204713 - EQUIPMENT: Repair instructions to address fault codes P204713 reductant injection valve control bank 1 unit 1 ⿿ circuit open
  • P203F00 - EQUIPMENT: Repair instructions to address fault codes P203F00 reductant level low
  • P203115 - EQUIPMENT: Repair instructions to address fault codes P203115 exhaust gas temperature sensor bank 1 sensor 2 - circuit short to battery or open
  • P10CE97 - EQUIPMENT: Repair instructions to address fault codes P10CE97 reductant return: no flow detected - componentor system operation obstructed or blocked
  • P107575 - EQUIPMENT: Repair instructions to address fault codes P107575 clutch system - emergency position not reachable
  • P107017 - BRAKES (PWS): Repair instructions to address fault codes P107017 gearbox brake valve (vagb) - circuit voltage above threshold
  • P040200 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Repair instructions to address fault codes P040200 engine exhaust gas recirculation 1 valve positionflow excessive detected
  • P029800 - ENGINE (PWS): Repair instructions to address fault codes P029800
  • P021700 - ENGINE AND ENGINE COOLING: Repair instructions to address fault codes P021700 engine coolant over temperature condition
  • NOx_Conv2 - EQUIPMENT:ELECTRICAL: Repair instructions to address fault codes P207F-00; P20EE-00
  • NOX_Conv1 - EQUIPMENT ADAPTIVE/MOBILITY: Repair instructions to address fault codes P207F-00 - reductant quality
  • FUELFILTER - ENGINE (PWS): Repair instructions to address fault codes P008A-00; P0087-00
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-19064 - STRUCTURE: Baggage door seal replacement
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-14076 - EQUIPMENT: This instruction sheets explains how to replace the fuel tank on h-series vehicles. (replacing older series tanks by newer model)
  • IS-19921A - EQUIPMENT: This instruction sheet explains how to install a seatbelt cutter in the driver's area
  • IS-19066 - SERVICE BRAKES, AIR: This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
  • SCI19-01C - ELECTRICAL SYSTEM: The intent of this procedure is to guide you through the steps required to program a mcm especially for the control of the electric fan drive as required for conversion kit of instruction sheets is-19900, is-19901, is19910, is-19912.
  • IS-19900G - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric fan drive cooling system conversion kit with bosch alternator - h3 series us10 cooling system
  • IS-19043 - EQUIPMENT: This instruction sheet explains how to relocate the wheel chair lift parcel rack fan
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19910E - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-19910D - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-19900E - ELECTRICAL SYSTEM: This instruction sheet explains how to install the electric fan drive cooling system conversion kit with bosch alternator - h3 series us10 cooling system
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • IS-19910C - ELECTRICAL SYSTEM: Electric fan drive cooling system conversion with delco remy alternator - h3 series us10 up to ghg17
  • IS-19900D - ENGINE AND ENGINE COOLING: Electric fan drive cooling system conversion with bosch alternator - h3 series us10 cooling system
  • IS-18910 - EQUIPMENT: This instruction sheet shows how to install a flap over the diesel filling cap.
  • IS-18091 - SUSPENSION: This instruction sheet explains how to install the tie rod 610052.
  • IS-17900A - STRUCTURE: Wheel fender stainless steel protector
  • WB19-07 - SERVICE BRAKES, AIR: On the independent front suspension (ifs) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
  • IS-19913 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators
  • IS-19908E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-19908A - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-19900A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to convert h3 series us10 vehicles equipped with bosch alternators to electric fan drive (efd) cooling system
  • IS-19913 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to install delco remy alternators
  • IS-18910 - FUEL SYSTEM, DIESEL: This instruction sheet explains how to install a flap over the diesel filling cap
  • IS-18115 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to install a gm glove box lock on h-series vehicles
  • IS-17905A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-17071A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • SCI19-01A - ELECTRICAL SYSTEM: This procedure explains how to program a mcm especially for the control of the electric fan drive, as required for conversion kit of instruction sheets is-19900 & is-19910.
  • IS-19910 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to convert h3 series us10 vehicles (equipped with delco remy alternators) to electric fan drive (efd) cooling system
  • IS-19908 - ELECTRICAL SYSTEM: This instruction sheet explains how to perform alternator conversion, from bosch to delco remy, on h3 vehicles
  • IS-19900 - ENGINE AND ENGINE COOLING: This instruction sheet explains how to convert h3 series us10 vehicles equipped with bosch alternators to electric fan drive (efd) cooling system
  • IS-15075 - STRUCTURE: This instruction sheet explains how to replace fenders made of fiber glass with aluminium
  • IS-13009D - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • SCI19-01 - EQUIPMENT: This procedure explains how to program a mcm especially for the control of the electric fan drive, as required for conversion kit of instruction sheets is-19900 & is-19910.
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • IS-13009C - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-18025 - ENGINE AND ENGINE COOLING: This instruction sheet shows how to replace kneeling level sensor #21643575 by sensor #22194741.
  • IS-18905 - EQUIPMENT: This instruction sheet explains how to install hatches with fan on h3 vehicles.
  • IS12010 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace the left bell crank using kit 161349
  • MI18-21A - ENGINE AND ENGINE COOLING: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI16-17G - ENGINE AND ENGINE COOLING: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • IS-15003E - ELECTRICAL SYSTEM: This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • MI18-21 - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presents information about the bitzer a/c compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
  • MI18-16A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information presents guidelines to help with the diagnosis of the bosch hd10 alternators
  • WB18-15 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?Low pressure warning? Set point.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • WB15-19H - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This bulletin explains how to add a reinforcement bracket to bitzer a/c compressor to increase the installation stiffness and reduce vibration amplitude.
  • MI18-02 - ENGINE AND ENGINE COOLING: This mainteannce informaiton presents the latest engine oil & filter change intervals for the volvo engine
  • MI16-17F - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternators
  • WB14-08C - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, verify the revision numbers of the steering wheel gateway module and multiplex software. If applicable, replace with the latest version. A power source improvement is also required. On some vehi
  • WB14-06G - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, perform the following verifications and modifications on the a/c system: bulletin is divided in five steps, refer to detailed instructions below. Step 1: unloader replacement (step moved to war
  • SP14-25 - ENGINE (PWS): On the vehicles affected by this bulletin, tighten the ball studs on the engine bay door gas springs.
  • MI1423 - ELECTRICAL SYSTEM:SOFTWARE: A new software version (v1.06) is available to update the cantrak (tire pressure monitoring system) module. This new version will allows a 10 min. Delay before the ?System error not all tires monitored? Message appears in the vehicle clust
  • MI1346 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: This maintenance information explains that on some post epa 2010 vehicles, it is possible for the combined charging and starting system f81 fuse to blow unexpectedly. To avoid this situation, a 3 amp diode can be added to the corresponding
  • IS-08080 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • MI13-33 - SUSPENSION:MULTIPLE AXLE:TORQUE ARM: This maintenance information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5
  • WB13-29 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: On the vehicles affected by this bulletin, a corrective measure is required due to bolts coming loose at the radiator fan clutch tripod attachment to the radiator. Addition of four (4) locknuts (jam nuts) will prevent bolts to loosen.
  • MI13-06 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: This maintenance information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocha
  • WB12-41A - ENGINE AND ENGINE COOLING: On the vehicles affected by this bulletin, an auxiliary coolant tank is available. This auxiliary coolant tank will prevent spillage due to expansion when main coolant surge tank is filled with too much coolant. *this warranty bulletin
  • WB12-31B - EQUIPMENT: On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
  • IS11015B - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
  • MI15-51 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This maintenance information explains how to run a n air conditionning performance test
  • MI15-61 - ENGINE (PWS): This maintrenance infomration explains that the castrol syntrans oil isn?T fully approved for 500 000 miles (800 000 km) extended drain intervals on the volvo i-shift transmission. For this reason, this oil has been downgraded to regular d
  • IS-15907A - EQUIPMENT:MECHANICAL: This instruction sheet explains how to assemble the bendix flr10 and flr20 radar sensor alignment tool
  • IS-14076 - FUEL SYSTEM, GASOLINE:STORAGE:AUXILLARY TANK: This instruction sheet does explain how to proceed to the fuel tank replacement, from # 031868 tank by newer 030008 model.
  • SP15-07B - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Following wb13-04, update the hot gas pickup tube circuit for an improved version with a better resistance to vibrations. This bulletin resolves a/c low pressure messages in the dashboard when the auxiliary fan is not running. The valve wil
  • MI15-41 - EXTERIOR LIGHTING:TAIL LIGHTS: This maintenance information reminds prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
  • MI15-43 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles equipped with bosch hd10 alternators.
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • IS-15003A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a altenrator conversion kit
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • IS-17071 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface on obd vehicles
  • SCI17-35 - ELECTRICAL SYSTEM:SOFTWARE: This internal instruction explains how to bench program the fms gateway module used in the eld (electronic logging device) interface kit for pre-obd13 vehicles.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • IS-17043A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to optimise the operation of the lavatory fan
  • MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-17900A - WHEELS: This instruction sheet explains how to install a wheel fender stainless steel protector
  • IS-16100 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: This instruction sheet explains how to install latest radio models
  • IS-15003D - ELECTRICAL SYSTEM: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • IS-17043 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to optimise the operation of the lavatory fan
  • MI15-43A - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on prevost vehicles.
  • WB15-19 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • SP15-07 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Following wb13-04, update the hot gas pickup tube circuit for an improved version with a better resistance to vibrations. This bulletin resolves a/c low pressure messages in the dashboard when the auxiliary fan is not running. The valve wil
  • CK17-27 - EQUIPMENT ADAPTIVE/MOBILITY: This conversion kit explains how to to disable the acb radar.
  • IS-15003B - EQUIPMENT: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • IS-14900 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to replace 562489 dimmer, using kit #069136
  • SP14-05B - ENGINE (PWS): On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 fmi 7 or spn641 fmi 7 or P004607 (obd13) are found. Bulletin affects d13h engines with serial number from 984581 up to 1026719, excluded.
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • Wb16-29 - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, update ems and acm software to the latest version available. This update must be carried out by qualified technicians. As soon as possible, make an appointment with your nearest prevost service cen
  • MI16-23 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information explains that decals are available to update the front junction box on 2013 to 2016 prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of t
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-14085 - EQUIPMENT: This instruction sheet explains how to prevent ac copper pipes chaffing at engine bulkhead
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • MI16-05 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This maintenance information shares information about the bendix m-32qr valve replaced by m-40qr model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
  • CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
  • IS-15003D - ENGINE (PWS): This insruction sheet explains how to insall the bosch hd10 24v-150a alternator conversion kit ? Twin bosch mounted on volvo d13 engine
  • WB14-47B - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a software update of ecm (engine control module) and acm (aftertreatment control module) to provide improved temperature-related behaviour. The software will also change urea dosing valve b
  • WB14-45C - ELECTRICAL SYSTEM:WIRING: On the vehicles affected by this bulletin remove the acm relay and base identified r49. Reconnect the 24v power wire and protect the remaining signal wires with shrink tube.
  • SP14-46 - EQUIPMENT ADAPTIVE/MOBILITY: This bulletin is performed on a fix as fail basis. On the vehicles affected by this bulletin, update to the latest configuration of wiring and sensors for the bitzer compressor.
  • WB14-44B - EQUIPMENT:ELECTRICAL: On the vehicles affected by this bulletin, changing of vecu (vehicle electronic control unit) parameters is necessary. This update must be carried out by qualified technicians. Make an appointment with your nearest prevost service center.
  • WB14-42A - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering gateway module. On a limited number of vehicles, the module will be replaced with the latest version of the part.
  • WB13-65D - ELECTRICAL SYSTEM:SOFTWARE: On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system, for the ems and aftertreatment control module (acm). On all vehicles, perform a dpf service regeneration and crystal subli
  • WB13-60 - POWER TRAIN: On the vehicles affected by this bulletin, a software update for the volvo i-shift transmission is required. Software update has for effect to improve the gear change process to avoid clashing and wear on the split gear. This software updat
  • WB13-63A - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
  • WB13-55A - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: On the vehicles affected by this bulletin, the upper support of the tripod fan support must be inspected for the presence of weld. If no weld is found, it must be replaced.
  • MI16-17E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This maintenance information explains how to remove and install the bosch hd10 (120a or 150a) alternator.
  • IS-17900 - EQUIPMENT: This instruction sheet explains how to install a wheel fender stainless steel protector
  • IS-15003C - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: This instruction sheet explains how to use the bosch hd10 24v-150a alternator conversion kit
  • WB15-19G - EQUIPMENT: On the vehicles affected by this bulletin, vibration is causing damage to a/c compressor and compressor harness connectors. Addition of a reinforcement bracket to bitzer a/c compressor is needed to increase the installation stiffness and re
  • MI16-34 - ELECTRICAL SYSTEM: "this maintenance information describes the steps to be followed on your computer to add the volvo engine brake auto mode on the vehicle. The auto mode may be added on us10 and obd13 vehicles that were built before the introduction of the
  • IS-08080A - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • SP14-05B - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER: Prevost: turbo inspection and replacement required for x3-45 coaches, xlii-45 entertainer, x3-45 vip motorhomes, h3-41coaches, h3-45 vip motorhomes. Model years 201-2014. *lj
  • MI-13-46 - ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS: Prevost: the combined charging and starting system f81 fuse, on some coaches, can unexpectedly blow and need a 3 amp diode to corresponding 24co circuit to prevent electrical back flow to fuse. Models 2011-2013 h3, h3-45 vip converted, x
  • WB-13-29 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Prevost: a corrective measure is required due to bolts loosen by being tightened to part made of rubber, causing the radiator fan clutch tripod to come loose and striking radiator core. *pe
  • MI-13-06 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Prevost: to increase vehicle's performance, a modification of hose clamp for cooling system connection, is recommended. Models 2010-13 h3, 2010-13 h3 vip converted, 2010-13 x3, 2012-13 x3 vip converted, 2010-13 mth xl2 entertainer, 2011 m
  • WB-12-31 - EQUIPMENT ADAPTIVE/MOBILITY: Prevost: information being provided regarding the replacement of dipstick on certain coaches. Models 2009-2013 h3-45, h3-41, x3-45, xl11-45, x3-45. *pe
  • WB-12-41 - ENGINE AND ENGINE COOLING:ENGINE: Prevost: warranty information provided regarding availability of an auxiliary coolant tank, when main coolant surge tank filled with too much coolant and auxiliary coolant tank prevents spillage due to expansion. Model 2010-2013 h3-41, h
Known Recall Investigations
  • Alternator front bearing failure investigation # PE21011

    Nhtsas office of defects investigation (odi) opened a preliminary evaluation after reviewing field reports concerning alternator front bearing failures that cause elevated temperatures within the engine compartment, resulting in the fire suppression system (fss) activating, immediately shutting the engine down, and rendering the bus inoperable.Analysis of the data provided by prevost car (us) inc. Showed high failure frequency and thermal events. An immediate shutdown of the bus can increase the risk of a crash or injury of bus occupants. In response to this investigation, prevost car (us) inc. And volvo bus corporation decided to conduct recalls 22v-221 and 22v-222. By submitting part 573 defect information reports on april 6, 2022, prevost car (us) inc. And volvo bus corporation notified odi of a safety defect in certain model year (my) 2010-2023 prevost h3-45; x3-45; x3-45 com; h3-45 vip: x3-45 vip and 2020 volvo 9700 vehicles; some of these buses may have experienced thermal events after failure of the alternator front bearing, because the alternator belt continues to turn the alternator after the bearing failure.These recall actions address the safety concern that led to the opening of this investigation.Therefore, with these recall actions, this investigation is closed. The recalls encompass all model and my vehicles addressed by the investigation. However, the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist in other model or my vehicles outside of the recall scope. The agency reserves the right to take further action if warranted by the circumstances.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.