IS-18091
Service Bulletin Details
Public Details for: IS-18091
This instruction sheet explains how to install the tie rod 610052.
- 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 - 2003 -
Models from 2019
2019 PREVOST H3-41 |
2019 PREVOST H3-45 |
Models from 2018
2018 PREVOST H3-41 |
2018 PREVOST H3-45 |
Models from 2017
2017 PREVOST H3-41 |
2017 PREVOST H3-45 |
Models from 2016
2016 PREVOST H3-41 |
2016 PREVOST H3-45 |
Models from 2015
2015 PREVOST H3-41 |
2015 PREVOST H3-45 |
Models from 2014
2014 PREVOST H3-41 |
2014 PREVOST H3-45 |
Models from 2013
2013 PREVOST H3-41 |
2013 PREVOST H3-45 |
Models from 2012
2012 PREVOST H3-41 |
2012 PREVOST H3-45 |
Models from 2011
2011 PREVOST H3-41 |
2011 PREVOST H3-45 |
Models from 2010
2010 PREVOST H3-41 |
2010 PREVOST H3-45 |
Models from 2009
2009 PREVOST H3-41 |
2009 PREVOST H3-45 |
Models from 2008
2008 PREVOST H3-41 |
2008 PREVOST H3-45 |
Models from 2007
2007 PREVOST H3-41 |
2007 PREVOST H3-45 |
Models from 2006
2006 PREVOST H3-41 |
2006 PREVOST H3-45 |
Models from 2005
2005 PREVOST H3-41 |
2005 PREVOST H3-45 |
Models from 2004
2004 PREVOST H3-41 |
2004 PREVOST H3-45 |
Models from 2003
2003 PREVOST H3-41 |
2003 PREVOST H3-45 |
Instruction Sheet IS-18091 Tie Rod 610052 installation instructions Prevost vehicles with S84 / S84U I-beam axles 1994- today Replaces 611024; 611025; 611292; 611026. First Release 05-28-2019 MATERIAL Kit #IS18091 includes the following parts: Part No. Description Qty 610052 TIE ROD ASSY 1 610051 NUT HEX SELF LOCKING M24-1.5 2 IS-18091 INSTRUCTION SHEET 1 FI-18091 FEUILLE D’INSTRUCTION 1 NOTE Material can be obtained through regular channels. PROCEDURE DANGER Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter type vehicles, set the battery master switch (master cut-out) to the OFF position. Lock out & Tag out (LOTO) must be performed during set-up, maintenance or repair activities. Refer to your local procedure for detailed information regarding the control of hazardous energy. u J t f a Dr Writer: FL 9 1 0 2 6 0 e nIS-18091 Page 2 / 3 1. Lift vehicle with mobile column lift. 2. Disassemble former tie rod by removing the cotter pin and castle nut (4). Disengage the ball joint pin from the levers. If your axle alignment was good, keep the tie rod for reference. FIGURE 1: 3. Clean all mating surfaces removing grease and corrosion. thoroughly, 4. Finish cleaning with brake cleaner fluid. FIGURE 2 5. Adjust the length of the new tie rod to fit the former tie-rod length by screwing / unscrewing ball joints by one turn increments. FIGURE 3: ADJUST BY ONE TURN INCREMENTS u J t f a Dr Writer: FL 9 1 0 2 6 0 e n IS-18091 Page 3 / 3 6. Once close to the length of the former tie rod, perform fine adjustment using the adjuster sleeve to reach the same length. (See Figure 4) NOTE: This sleeve is also used to fine adjust toe-in to the values applicable to your specific axle. Refer to Maintenance Information MI18-45 and your vehicle’s maintenance manual in Section 14Steering under “Front Wheel Toe-in”. FIGURE 4 7. Install new tie rod. Orient tube bend so it is pointing down and parallel to the axle beam. FIGURE 5: TIE ROD ORIENTATION 8. Tighten ball joint self-locking nut (item 1) to 155-170 lb-ft (210-230 Nm) These nuts are single use and should be replaced every time they are unscrewed. 9. Tighten clamp bolts (item 2) to 107-129 lb-ft (145-175 Nm) FIGURE 6 Maintenance information For further information refer to maintenance information MI18-45, available on the Prevost technical publications web site. PARTS / WASTE DISPOSAL 9 1 0 2 6 0 e n Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/ Federal) u J t f a Dr Writer: FL