Prevost H3-41 2009

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2009 PREVOST H3-41.

ManufacturerKnown WMI(s)Fuel Type
PREVOST
PREVOST VIN Decoder

Use the box here to look up VINs from PREVOST as well as other manufacturers

#

Sub-models: - H3-41 Coach -

Frequently Asked Questions
  • Are there recalls for the 2009 PREVOST H3-41?
     - There are 14 recall(s) for the 2009 PREVOST H3-41, additional information is below.
NHTSA Mandated Recalls
  • Recall 138322 [USA]: If the fuel tank separates from the vehicle, it could be a road hazard and the vehicle would stall. either scenario increases the risk of a crash.

  • Recall 108571 [USA]: The fuel line rubbing may result in abrasion and a fuel leak, increasing the risk of a fire.

  • Recall 101800 [USA]: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.

  • Recall 99635 [USA]: If the springs break, the pedal may not return to idle once the driver lifts their foot off the pedal. this unintended acceleration increases the risk of a crash.

  • Recall 93730 [USA]: Uncontrollable throttle position may lead to a loss of vehicle control, increasing the risk of a crash.

  • Recall 68897 [USA]: The user of the lift could be injured should the lift move without the restraint belt properly buckled.

  • Recall 82189 [USA]: In the event of a crash, a seat occupant may not be properly restrained increasing the risk of personal injury.

  • Recall 81768 [USA]: If the bolts break, the escape hatch can fall down on to the roadway, increasing the risk of property damage or a crash.

  • Recall 2013139 [Canada]: Steering

  • Recall 2013059 [Canada]: Other

  • Recall 2012191 [Canada]: Other

  • Recall 2010087 [Canada]: Other

  • Recall 2008356 [Canada]: Other

  • Recall 2008405 [Canada]: Other

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • IS-23019 - SUSPENSION: Sway bar collars improvement
  • IS-22106 - EQUIPMENT: H3 lavatory fan retrofit kit
  • IS-18106 - STEERING: Kit power steering tank convertion cummins to zf with d13 engine
  • MI16-32 - ENGINE AND ENGINE COOLING: Improved bearings are now available to replace the original bearings used on some prevost vehicles idler pulleys.
  • IS-21072B - ELECTRICAL SYSTEM: Steering gateway. Revision b - pin 2 and 10 were inverted on connector a139
  • MI22-12B - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: b - general update
  • MI22-12A - SERVICE BRAKES, AIR: Air tanks draining sequence. Revision: a - erroneous secondary & accessory tanks location.
  • MI22-12 - SERVICE BRAKES, AIR: Air tanks draining sequence
  • IS-17151C - EXTERIOR LIGHTING: Halogen to led fog light replacement kit. Revision: c - advanced kits canceled
  • MI20-08C - EQUIPMENT: Storage and startup guidelines : part number updates
  • IS21-072A - ELECTRICAL SYSTEM: Steering gateway revision a cancel watch dog removal from efd part of the instruction
  • IS20-925A - VISIBILITY: Central hvac merv filters installation
  • IS20-932A - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • Mi21-07A - WHEELS: Ront & tag axle ⿿ unitized hub bearing end play verification and replacement
  • is_20089 - LATCHES/LOCKS/LINKAGES: Lavatory compartment sliding door latch improvement
  • IS-08080B - EQUIPMENT: Sound selector replacement, vss04 to vss05; when replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new
  • MI20-08C - STRUCTURE: Storage and startup guidelines: periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, prevost recommends foll
  • IS-20925A - POWER TRAIN: Central hvac merv filters installation reva
  • IS-20932A - EQUIPMENT: H3 series envirocare - ions air sanitizer rev a
  • IS-20932 - EQUIPMENT: H3 series envirocare - ions air sanitizer
  • IS-18091A - STEERING: Tie rod 610052 first installation instructions: use these instructions when replacing the drop joint tie rod on s82, s84 / s84u i-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment ne
  • MI20-19B - ENGINE AND ENGINE COOLING: Introducing a new engine coolant into prevost service center network
  • MI20-19A - ENGINE AND ENGINE COOLING: Rev a: mention added concerning ddc series 60 engine sca requirement
  • MI20-19 - EQUIPMENT: Introducing a new engine coolant into service
  • MI02-17A - EQUIPMENT ADAPTIVE/MOBILITY: Revision : a torque value reduced
  • IS-19165A - ELECTRICAL SYSTEM: Lavatory fan retrofit kit applicable for h3 series coaches from r-1012 (1994) revision a: added installation detail at step 8
  • SCi20-16 - ENGINE AND ENGINE COOLING: Fan clutch plate bolts re-torquing
  • IS-20923 - EQUIPMENT: H3 driver⿿s partition lite installation
  • MI20-08B - EQUIPMENT: Storage and startup guidelines revision: b parts added to suggested material 08-10-2020
  • IS-20922 - EQUIPMENT ADAPTIVE/MOBILITY: Sigma passenger seats partition kit
  • MI20-12 - STEERING: Jerky, noisy or hard to turn steering gearbox. Hydraulic end limiter adjustment. All models ⿿ equipped with rb bosch/zf servocom or servocomtronic steering gearbox
  • IS-20906 - EQUIPMENT ADAPTIVE/MOBILITY: Plexiglass shield behind driver h3 series
  • MI20-08A - EQUIPMENT: Storage and startup guidelines: rev a: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
  • MI20-09 - EQUIPMENT:OTHER:LABELS: Prevost vehicle disinfection procedure
  • MI20-08 - UNKNOWN OR OTHER: Storage and startup guidelines - all prevost vehicles & volvo 9700
  • IS-19064 - STRUCTURE: Baggage door seal replacement
  • MI15-24 - EQUIPMENT ADAPTIVE/MOBILITY: Added: power cables for l.H. Side alternator & fan drive breaker box
  • IS-14076 - EQUIPMENT: This instruction sheets explains how to replace the fuel tank on h-series vehicles. (replacing older series tanks by newer model)
  • IS-19043 - EQUIPMENT: This instruction sheet explains how to relocate the wheel chair lift parcel rack fan
  • IS-17151 - LIGHTING (PWS): This instruction sheet explains how to replace halogen fog light to led's
  • IS-19910E - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-19910D - ELECTRICAL SYSTEM: This instruction sheet explains how to perform an electric fan drive cooling system conversion with delco remy alternator - h3 series us10 to ghg17 included
  • IS-18091 - STEERING: This instruction sheet explains how to perform the first installation of tie rod 610052 on prevost vehicles equipped with dana s82, s84 / s84u i-beam axles, 1994- today
  • MI18-45A - POWER TRAIN: Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to is-18091 for installation instruction
  • IS-18091 - SUSPENSION: This instruction sheet explains how to install the tie rod 610052.
  • IS-17910A - EQUIPMENT: Message center display (mcd) replacement
  • IS-19916 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: This instruction sheet explains how to install the audio converter 405842
  • IS-17905A - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-11003G - EQUIPMENT: This instruction sheet explains how to replace the ?Master id? With ?Mcm? Module
  • IS-13009D - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-11003F - ELECTRICAL SYSTEM: This instruction sheet explains how to replace the "master id with mcm" module
  • SCI18-46 - EQUIPMENT:ELECTRICAL: This service center instructions explains how to install the prevost ultimate entertainment system
  • IS-13009C - STEERING:LINKAGES:DRAG:LINK:CONNECTION: This instruction sheet explains how to install and adjust drag link # 660699
  • IS-18905 - EQUIPMENT: This instruction sheet explains how to install hatches with fan on h3 vehicles.
  • IS-17910 - EQUIPMENT: This instruction sheet explains how to replace the message center display (mcd)
  • IS12010 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace the left bell crank using kit 161349
  • MI16-08B - EQUIPMENT ADAPTIVE/MOBILITY: This maintenance information presentes the new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts.
  • IS-17905 - ELECTRICAL SYSTEM: This instruction sheet explains how to install an eld interface kit on pre-obd prevost vehicles equipped with volvo d13 engines
  • IS-13009B - EQUIPMENT:MECHANICAL: This instruction sheet explains how to install and adjust drag link # 660699
  • MI1423 - ELECTRICAL SYSTEM:SOFTWARE: A new software version (v1.06) is available to update the cantrak (tire pressure monitoring system) module. This new version will allows a 10 min. Delay before the ?System error not all tires monitored? Message appears in the vehicle clust
  • IS-08080 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • MI13-33 - SUSPENSION:MULTIPLE AXLE:TORQUE ARM: This maintenance information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5
  • WB12-31B - EQUIPMENT: On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
  • MI15-51 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: This maintenance information explains how to run a n air conditionning performance test
  • MI15-61 - ENGINE (PWS): This maintrenance infomration explains that the castrol syntrans oil isn?T fully approved for 500 000 miles (800 000 km) extended drain intervals on the volvo i-shift transmission. For this reason, this oil has been downgraded to regular d
  • MI15-56 - EQUIPMENT ADAPTIVE/MOBILITY: On vehicles mentioned above, should the curbside electric sunshade fail to operate without encountering a drive mechanism issue, perform the following procedure.
  • MI15-18 - EQUIPMENT: This maintenance information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
  • MI15-24 - EQUIPMENT:MECHANICAL: This maintenance information explains how to perform an inspection of the vehicle power cables. Power cables in poor condition can be the cause of failures and serious damages in the engine compartment.
  • IS-17907 - EQUIPMENT:ELECTRICAL: This instruction sheet explains how to install the volvo electronic logging device (eld)
  • SCI17-35 - ELECTRICAL SYSTEM:SOFTWARE: This internal instruction explains how to bench program the fms gateway module used in the eld (electronic logging device) interface kit for pre-obd13 vehicles.
  • MI17-22 - FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY: This maintenance information explains how to inspect the fuel tank cradle mounting screws on a yearly basis
  • MI15-02 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: This maintenance information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "j" shaped hose that prevents oil leakage and water ingestion while allowing the axle
  • Mi16-15 - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-16100 - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: This instruction sheet explains how to install latest radio models
  • IS-11003A - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to replace master id? With ?Mcm? Module
  • IS-14900 - EQUIPMENT ADAPTIVE/MOBILITY: This instruction sheet explains how to replace 562489 dimmer, using kit #069136
  • MI16-15B - EQUIPMENT:RECREATIONAL VEHICLE/TRAILER:LPG SYSTEMS:TANK VALVE/GAUGE: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-11003D - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to remplace master id? With ?Mcm? Module
  • MI16-22 - EQUIPMENT ADAPTIVE/MOBILITY: Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.
  • MI16-15A - TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS: The beru sensors used on prevost vehicles to monitor tire pressure (tpms system) are being replaced by new huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, repla
  • IS-14085 - EQUIPMENT: This instruction sheet explains how to prevent ac copper pipes chaffing at engine bulkhead
  • MI16-16 - ELECTRICAL SYSTEM: This procedure explains how to perform a starter removal and installation, and does apply to melco 105p70 starter part number #21212425.
  • CK17-19A - EQUIPMENT: This conversion kit explains how to remove tgw1 from vehicles using tech tool, no manual vda changes needed. This conversion kit will work for any vehicle equipped with tgw1 up to the vin's listed on the bulletin.
  • IS-11003E - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : This instruction sheet explains how to remplace master id? With ?Mcm? Module
  • IS-17901 - BRAKES (PWS): This instructions sheet explains how to program a wabco smart trac abs ecu.
  • MI16-08 - EQUIPMENT:MECHANICAL: On receiving your kit masters fan clutch you may notice a new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts. Applies
  • IS-17900 - EQUIPMENT: This instruction sheet explains how to install a wheel fender stainless steel protector
  • IS-08080A - EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.: When replacing a vehicle sound selector model vss04 with a new sound selector model vss05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new vss05 compatible radio unit must also be in
  • MI-12-11-A - ENGINE (PWS): Prevost: information being provided regarding the modification of d13 us07 engines' improved belt tensioner to prolong belt life. *pe
  • SCI10-02 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Prevost: installin an air deflector in order to reduce ambient temperature around linnig radiator fan gearbox. *kb
  • WB10-26A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine correction of the drv control valve air supply circuit. *kb updated on 5/9/2012. *kb
  • WB10-17 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine - turbocharger smart remote actuator (sra) faults. *kb
  • WB10-15A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine - new egr mixer inlet tube. *kb
  • WB10-18 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine oil seepage at unit injector harness pass-through fitting. *kb
  • WB11-05 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Prevost: exhaust pipe angle bracket inspection. *kb
  • WB11-02 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: replacing t1 bosch alternators and water pump belt tensioners. *kb
  • WB11-01A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine - aftertreatment hydrocarbon injector (ahi) fuel line fittings - proper tightening verification. *kb
  • WB11-22 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine harness replacement - oil seepage at unit injector pass - through fitting. *kb
  • WB09-25 - ENGINE AND ENGINE COOLING:ENGINE: Prevost: on volvo d13 engines dashboard 'check engine' warning lamp could come on due to code pid 110. Also included model mth xll45e bus model year 2009 *js
  • WB09-23 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Prevost: preheater exhaust pipe holding clamp may not be properly positioned. Make sure that the holding clamp is located above the splash guard and not beneath. *js
  • WB09-26 - ENGINE AND ENGINE COOLING:ENGINE: Prevost: on volvo d13 engines dashboard 'check engine' warning lamp could come on due to code pid 171. Also included model mth xlii-45e bus shells model year 2009. *js
  • WB09-13A - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Prevost: inspecting the radiator fan drive mechanism support on a detroit diesel engine. Also included model vip-45 bus model years 2001-2010; model xlii mth bus model years 2008-2009. *js
  • WB09-01 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Prevost: coaches exhaust system update in order to modify exhaust fumes path, increase diffuser performance and reflect latest improvement. Models include h3-41 and h3-45 model years 2007-2009; model x3-45 model year 2008. *js
  • SCI11-11 - UNKNOWN OR OTHER: Prevost: kidde fire extinguisher control head replacement. *kb updated 5/9/2012. *kb
  • MI11-27 - EQUIPMENT:APPLIANCE:AIR CONDITIONER: Prevost: 12" brushless condenser fan replacement. Models include xlii mth, and h3vip mth. Model years are 2008-2011. *kb
  • WB10-01A - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine: replacement of copper injector sleeve with conical stainless steel injector sleeve. *kb updated 5/4/2012. *kb
  • WB10-36A - ELECTRICAL SYSTEM: Prevost: reprogramming of i/o-a & i/o-b modules for implementation of the essential functions to operate the vehicle (basic limp-home functions). *kb
  • WB08-18 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine- water pump replacement (ref. Sp262-003). *js
  • WB08-15 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Prevost: volvo d13 engine with veb (volvo engine brake)- rocker arms replacement & camshaft inspection (ref. Sp215-015) contact your prevost regional service manager to find out the nearest service center location. *js
  • WB08-14 - UNKNOWN OR OTHER: Prevost: addition of decal on the steering column. There is a possibility that the decal was not installed on the steering column. Also included model mth h3-45 vip model year 2008. *js
  • WB08-13 - ELECTRICAL SYSTEM: Prevost: replacement of the dashboard stationary regeneration switch- detroit diesel only.This switch would not be able to initiate a staionary regeneration after ddec vi software upgrade. Also included model vip motorhomes model years 2007

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.