IS-19910E

Instruction Sheet
IS-19910E
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH
DELCO REMY ALTERNATOR
H3 coaches (2PCH…) US10 to GHG17 incl. (B-1721 to J-0184)
REVISION E:
09-18-2019
THIS DOCUMENT SUPERSEDES PREVIOUS VERSION.
Mention added concerning recommended Delco Remy conversion kits
Recommended Alternator Conversion Kits
Take note that you can install a Delco Remy 55SI 24V-250A alternator on the engine curbside using one
of the following recommended installation kit:
Kit:
IS19913
Applicable to: H3 Series, US10
Kit:
IS19908
Applicable to: H3 Series, from D-2364 up to J-0184
MATERIAL
Kit IS19910 contains the following parts:
Qty
Part No.
DESCRIPTION
050195
FAN SUPPORT PANEL
A1
1
050200
UPPER SHROUD TRANSITION
A6
1
050201
LEFT SHROUD TRANSITION
A7
1
050202
RIGHT SHROUD TRANSITION
A8
1
050203
LOWER SHROUD TRANSITION
A9
1
050204
UPPER LEFT SHROUD PANEL H3 US10+
A11
1
050229
ELECTRICAL CONNECTOR COVER
A15
1
050206
UPPER RIGHT SHROUD PANEL H3 US10+
A12
1
050213
LOWER SHROUD PANEL H3 US10+
A14
1
050208
LH SIDE SHROUD PANEL H3 US10+
A10
1
Writer:
EL

IS-19910E
Page 2 / 74
050255
RH SIDE SHROUD PANEL & WURTH BOX SUPPORT
H3 US10+
A13
1
012349
IDLER PULLEY
Mechanical
1
012941
PULLEY, DRIVE
Mechanical
1
010090
L.H. ENGINE MOUNT
Mechanical
1
011213
SUPPORT, IDLER + TENSIONER
069893
PULLEY, DELCO REMY ALTERNATOR 10PK 69 DOB
Mechanical
1
453076
CAP, DUST
Mechanical
1
Writer: EL
Mechanical
1

IS-19910E
Page 3 / 74
506067
1x BELT 10PK1703 ARAMIDE
1x BELT 10PK1703 ARAMIDE (for your spare kit)
Mechanical
2
510991
TENSIONER, BELT
Mechanical
1
560720
DELCO REMY ALTERNATOR 55SI 24V-250A
Mechanical
1
050286
CAC INLET PIPE H3 US10+
Pipe
1
050406
CAC OUTLET PIPE H3 US10+
Pipe
1
050414
RADIATOR INLET COOLANT PIPE H3 US10+
Pipe
1
050288
RADIATOR OUTLET PIPE H3 US10+
Pipe
1
501027
FITTING, SAE 45º #4FL-Mx1/4NPT-M BR
Fitting
1
501308
ADAPTER / PIPE FITTING / 1/4NPT-Fx1/4NPT-M BR
Fitting
1
501329
ELBOW 45º / PIPE FITTING / 1/4NPT-Mx1/4NPT-F BR
Fitting
1
501332
ELBOW 90º / PIPE FITTING / 1/4NPT-Mx1/4NPT-F BR
Fitting
1
052366
HOSE 3/8 ID X 61'' LONG
hose
1
20550690
HOSE, FLEXIBLE - CHARGE AIR
Hose
2
Location: turbo outlet & engine intake
Writer: EL

IS-19910E
Page 4 / 74
531469
HOSE, FLEXIBLE - CHARGE AIR
Hose
1
Hose
1
Hose
1
Hose
3
Clamps
8
Clamps
4
Clamps
16
Clamps
4
Location: CAC outlet
531471
HOSE, FLEXIBLE - CHARGE AIR
Location: CAC inlet
052889
HOSE, SILICONE 2 1/2" ID
Location : coolant pipes
053617
HOSE, SILICONE
Location : coolant pipes
21490616
CLAMPS, SPRING LOAD - CHARGE AIR
Location: CAC outlet & inlet
21490630
CLAMP, SPRING LOAD - CHARGE AIR
Location: turbo outlet & engine intake
992089
HOSE CLAMP CT CAILLAU 60mm-80mm
Location : coolant pipes
992081
HOSE CLAMP CT CAILLAU 12-22
Location : coolant filter
21185073
MOUNT, ANTI-VIBRATION
Support
/bracket
1
050305
BRACKET, RADIATOR INLET PIPE
Support
/bracket
1
Writer: EL

IS-19910E
Page 5 / 74
050265
COOLANT FILTER SUPPORT H3
Support
/bracket
1
050303
ALTERNATOR TELLTALE BRACKET
Support
/bracket
1
050214
UPPER RADIATOR SUPPORT H3
Support
/bracket
1
069890
LH LOWER ALTERNATEUR SUPPORT
Support
/bracket
1
069891
LH UPPER ALTERNATEUR SUPPORT
Support
/bracket
1
069205
DECAL, WARNING
Misc.
2
010111
DECAL, BELT
Misc.
1
391028
INSERT, ALTERNATOR TELLTALE
Misc.
1
506025
RUBBER EXTRUSION, BLACK
Misc.
8 ft
380360
GROUND STUD
Misc.
1
506040
TAPE, ADHESIVE AD1 EPDM CC GY 5/16"X3/4"X25'
Misc.
1
562113
TELLTALE LIGHT MODULE
Misc.
1
Writer: EL

IS-19910E
Page 6 / 74
Misc.
1
Electrical
1
CONNECTOR HOUSING, PED WEATHER-PACK 4
WIRES
Electrical
1
561783
CAVITY PLUG, CONNECTOR
Electrical
4
22722850
I/O-B MULTIPLEX MODULE
Electrical
1
23499009-EFD
MCM, PROGRAMMED
Electrical
1
563593
CONNECTOR, WITH END-OF-LINE 120 OHMS
RESISTOR
Electrical
2
563750
FUSE HOLDER, AMG TYPE
Electrical
1
564520
FUSE, AMG 300A
Electrical
1
564612
CIRCUIT BREAKER BOX, WURTH
Electrical
1
565191
FAN, ELECTRIC
Electrical
8
21937327
FILTER, COOLANT
012921
GROUND STUD
561610
Writer: EL

IS-19910E
Page 7 / 74
563533
HAND GUARD, FAN
Electrical
8
23498721
FAN DRIVE POWER CABLE, 4600mm
Harness
1
23524934
L.H. ALTERNATOR POWER CABLE – DELCO REMY
Harness
1
23498450
MASTER RELAY TO 300A FUSE CABLE, 300mm
Harness
1
23445869
MCM TO I/O-B INTERFACE HARNESS
Harness
1
23488790
FAN TO RJB INTERFACE HARNESS H3
Harness
1
23490553
VEHICLE INTERFACE HARNESS
Harness
1
068820
HARNESS, FAN DRIVE
Harness
1
069246
GROUND CABLE, FAN DRIVE
Harness
1
0610037
CONTROL HARNESS, LEFT ALTERNATOR
Harness
1
0610035
GROUND CABLE, LEFT ALTERNATOR
Harness
1
N37749
TIE, NYLON, DOUBLE
hardware
15
509491
TIE, NYLON LARGE EXTRA STRONG 250 LBS
hardware
38
504016
TIE, NYLON BLACK (LARGE)
hardware
58
504013
MOUNT, TIE HOLE 1/4"
hardware
25
504751
MOUNT, TIE SWIVEL
hardware
4
Writer: EL

IS-19910E
Page 8 / 74
504750
MOUNT, TIE TREE
hardware
1
509490
MOUNT, TIE DOUBLE GRAY
hardware
15
562679
MOUNT, SQUARE SELF-ADHESIVE BLACK
hardware
4
500411
WSH FL SS .260X.697X.05 (M6,1/4)
hardware
500449
WASHER, FLAT SS .687X1.5X0.078 (M16,5/8)
hardware
1
1
500482
WASHER, SPLIT LOCK Z050 .506X.873X.125
(M12,1/2)
hardware
1
500942
WASHER, SPLIT LOCK N500 8.1X14.8X2
(M8,5/16,#18)
hardware
4
502570
WASHER, SPLIT LOCK SS 6.1X11.8X1.6 (M6,#12)
hardware
62
502573
WASHER FL SS 6.4 X 12.0 X 1.6 (M6,1/4)
hardware
1
507657
5001137
WASHER, BANJO FITTING M14
WSH FL SS .203X.438X.06 (M5,#10)
hardware
8
hardware
5001341
WASHER, FLAT SS 8.4X17X1.6 (M8,5/16)
hardware
2
7
5001737
WASHER, SPLIT LOCK N500 10.2X18.1X2.2
(M10,3/8)
hardware
4
5001751
WASHER, FLAT N500 10.5X26X2 (M10,3/8)
hardware
10
5001833
WASHER, BELLEVILLE SPR SS 301
6.65X17.4X1.27(M6,1/4
hardware
32
5001868
WASHER, BELLEVILLE SS 8.4X18X2 (M8,5/16)
hardware
4
5001935
WASHER, FLAT SS 10.5X18X1.6 (M10,3/8)
hardware
1
5002008
WASHER, FLAT HARD N500 13X35X5 (M12,1/2)
hardware
1
500998
NUT HEX BR 1/2-13
hardware
1
502837
NUT HEXF STO N500 M8-1.25
hardware
2
502859
NUT HEX NYRT NX500 M10-1.5 G10
hardware
4
5001180
NUT HEX NYRT SS 10-24
hardware
2
Writer: EL

IS-19910E
Page 9 / 74
hardware
1
hardware
1
hardware
2
hardware
2
hardware
3
hardware
1
hardware
hardware
4
11
1
hardware
33
hardware
8
hardware
22
hardware
6
hardware
hardware
4
3
hardware
62
hardware
4
hardware
2
hardware
1
hardware
4
hardware
2
SCR CAP HEXF N500 M10-1.5X120 G10.9
hardware
504379
RIVET, POP DOME SS OE 3/16X1/4
hardware
4
41
504610
RIVET MGL PRDG SS 1/4X5/8
hardware
14
IS-19910
INSTRUCTION SHEET
5001182
NUT HEX NYRT SS M6-1
5001665
NUT HEX NYRT NX500 M22-2.5
5001761
NUT HEXF NYRT NX500 M12-1.75 G8
5001930
NUT HEXF NYRT NX500 M10-1.50 PC 10
5001983
500685
NUT HEX NYRT NSS M8-1.25
NUT HEX NYRT SS 5/16-18
500119
500658
SCREW, CAP HEX SS NSS M8X1.25X20
SCREW TC PAN PH Z050 10-24X3/4
502719
SCREW, CAP HEX SS NSS M10X20 G8.8
502686
SCREW, CAP HEX SS NSS M6X30
502804
SCREW, CAP HEX N500 M10-1.5X25 G8.8
502848
SCREW TC HEX F N500 1/4-20X3/
5001296
5001308
SCREW, CAP HEXFN500 M12-1.75 X 80 CL10.9 PT
SCR CAP HEXF N500 M10-1.5X40 G10.9
5001643
SCREW, CAP HEXF G500 M8-1.25X25 G8.8 PT
5001697
SCREW, CAP HEX SS NSS M6X16
5001738
SCREW, CAP HEX N500 M8X30 G8.8 FT
5001745
SCREW, CAP HEX N500 M8-1.25X25 G8.8
5001786
SCREW, CAP HEXF AD N500 M12-1.75X30 G8.8
5001799
SCREW, CAP HEXF N500 M10-1.5 X 70 G10.9
5001940
SCREW CAP HEX N500 M12X1.75X140
5002091
Writer: EL
hardware
1

IS-19910E
Page 10 / 74
Other parts or products that may be required:
Part No.
DESCRIPTION
680459
Loctite 404, INSTANT ADHESIVE 9.3gr
680098
LOCTITE 567 THREAD SEALANT 250ML
680038
LOCTITE 243, BLUE THREADLOCKER 50ML
NOTE
Material can be obtained through regular channels.
Writer: EL

IS-19910E
Page 11 / 74
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the
ignition switch to the OFF position and trip the main circuit breakers equipped with a trip
button.
ELECTRICAL CABLES & HARNESSES DIAGRAM
Writer: EL

IS-19910E
Page 12 / 74
HOSE CLAMP TORQUE (coolant lines and charge air cooler)
Writer: EL

IS-19910E
Page 13 / 74
HOSE CLAMPS
No
1
(Ø 2 ½ ” or
lower)
2
(Ø 4 ¼ ”)
Writer: EL
DESCRIPTION
TORQUE
Constant-Torque hose clamps - coolant lines
90-100 lbf-in
Oetiker hose clamps – Green spring - coolant lines
12-18 lbf-in
Oetiker hose clamps – unpainted spring - coolant lines
8-9 lbf-in
Caillau hose clamps - coolant lines
30 lbf-in
Constant-Torque hose clamps 4.25in - charge air cooler
(CAC)
4.5-5.5 lbf-ft

IS-19910E
Page 14 / 74
Writer: EL

1. In the main power compartment, place the
battery master switch to the OFF position. Trip
all the main breakers that have a manual trip
(CB2,
CB4,
CB6,
lever
or
button
etc…depending on the year model).
2. Remove L.H. side rear fender.
FIGURE 1
Drain the cooling system
3. Connect the coolant extractor. Use the coolant
extractor to drain the coolant from the engine.
An alternate method is to drain the coolant into
a suitable container using the drain hose.
FIGURE 2
Writer:
EL

IS-19910E
Page 16 / 74
4. Unfasten cap screws and remove access
panel located behind tag axle L.H. side wheel.
FIGURE 3
5. Open radiator door to access radiator
assembly. Unfasten upper arm assembly.
FIGURE 4
6. Remove radiator sealing frame.
FIGURE 5
Writer: EL

IS-19910E
Page 17 / 74
7. Remove clamps and then break hoses from
the front coolant and charge air pipes.
FIGURE 6
8. Remove rear coolant and charge air hose
clamps then break hoses loose.
FIGURE 7
9. Remove the upper radiator assembly support
bracket.
Keep the three small (3) rectangular plates for
reuse
FIGURE 8
Writer: EL

IS-19910E
Page 18 / 74
10. Remove the lower radiator assembly protector
tube.
FIGURE 9
11. Disconnect the radiator vent hose on top of
the radiator.
12. Cut the cable tie and disconnect electrical
connector from the fan clutch. The remaining
connector on the chassis cable will be capped
and left in place.
13. Remove fan drive shaft fasteners at the fan
clutch.
FIGURE 10
Writer: EL

IS-19910E
Page 19 / 74
14. Open the secondary lock of connector
#561610. Insert a cavity plug #561783 in each
of the four (4) cavities with the smallest end
protruding as shown on the example at right.
Close the secondary lock.
15. Cap the chassis fan clutch cable with this
connector. Secure the connector on the inner
wall above the radiator using:
•
•
1x tree mount #504750
1x nylon tie #504016
FIGURE 11
FIGURE 12
FIGURE 13
16. Remove the fan drive casting.
FIGURE 14
Writer: EL

IS-19910E
Page 20 / 74
17. Unscrew all lower radiator assembly mounting
fasteners (2 bolts on R.H. side, 2 bolts on L.H.
side).
FIGURE 15
18. Position a forklift under the radiator assembly
that is capable of safely lifting the radiator. With
assistance, slide radiator assembly out and
onto the forklift. Transfer radiator assembly to a
secure location.
FIGURE 16
Writer: EL

IS-19910E
Page 21 / 74
19. Remove the tripod from the radiator/CAC
assembly.
FIGURE 17
FIGURE 18
20. Remove the fan shroud.
FIGURE 19
Writer: EL

IS-19910E
Page 22 / 74
21. The new cooling pack arrangement requires
being located four inches closer to the engine
to give the needed clearance for the electric
fans. For this reason, rotate both the
radiator/CAC assembly mounting supports
180° and reinstall.
BEFORE
FIGURE 20: MOUNTING SUPPORT IN INITIAL POSITION
AFTER
FIGURE 21: MOUNTING SUPPORT AFTER 180° ROTATION
22. Remove the rear bumper (undo three nuts and
one attachment plate each side).
FIGURE 22
Writer: EL

IS-19910E
Page 23 / 74
23. On the engine hot side, remove the following
pipes:
•
•
radiator inlet & outlet pipes
CAC inlet and outlet pipes
Keep the hose clamps, the flexible hoses for
later reuse
Keep the fittings found on the pump inlet pipe
for later reuse
FIGURE 23
FIGURE 24
24. Remove all the drive belts mounted on the
crank pulley.
FIGURE 25
Writer: EL

IS-19910E
Page 24 / 74
25. Remove the drive pulley. Discard the 6 bolts.
FIGURE 26
26. Remove the rust, clean and prepare the
surface on the vibration damper as shown.
Make a smooth surface for the pulley that will
be reinstalled later on.
FIGURE 27
FIGURE 28
Writer: EL

IS-19910E
Page 25 / 74
27. Properly support the engine as one of the
engine support will be interchanged.
FIGURE 29
28. Remove the two (2) coolant hoses shown on
the image. Keep the two (2) banjo fittings for
later use.
BANJO FITTING
FIGURE 30
29. Remove the L.H. rear engine support on which
the coolant filter is installed (10 bolts). Keep the
hardware for reuse.
Take note that the water pump belt
idler/tensioner assemble will be reused as
is. Do not take apart tensioner or idler.
FIGURE 31: L.H. REAR ENGINE SUPPORT
Writer: EL

IS-19910E
Page 26 / 74
30. Cut the engine cradle rail as shown to increase
the clearance between the cradle and the
alternator. Carefully work the edge to achieve a
smooth finish and contour.
Wear
appropriate
equipment.
personal
protection
Protect engine and area with blankets.
Blow area clean when completed.
Apply paint to protect the bare metal
FIGURE 32
31. Remove the water pump idler/tensioner
assembly from the former engine mount. To do
so, unscrew three (3) bolts at the back of the
engine mount.
FIGURE 33
Writer: EL

IS-19910E
Page 27 / 74
32. Reinstall the idler/tensioner assembly as a unit
on the new L.H. engine mount #010090.
Mount the idler/tensioner assembly using
three (3) cap screws #5001643
Tighten to 14-17 lb-ft
FIGURE 34
FIGURE 35
Writer: EL

IS-19910E
Page 28 / 74
33. Install the new engine mount #10090 using
seven (7) M14 screws saved from the former
engine support with the exception of:
•
Ground stud #012921 (1x) and nylon
insert NYRT nut #5001665 (1X)
•
•
Isolator cap screw #5001940 (2X)
Nut #5001761 (2X)
FIGURE 36
Seven (7) mounting screws torque : 90-94 lb-ft
(128 Nm)
FIGURE 37
Tighten ground stud to 94 lb-ft
Tighten stud nut to 94 lb-ft
FIGURE 38
Tighten isolator screws to 60 lb-ft
Writer: EL

IS-19910E
Page 29 / 74
34. Install the new crank pulley using six new bolts
#5001296. Use blue Loctite on the bolt threads.
Torque to 26 lb-ft in the numerical order 1,
2, 3, 4, 5, 6, 1
Once done perform a final tightening to the
value of 66 lbf-ft.
FIGURE 39
35. Reinstall the water pump drive belt.
FIGURE 40: WATER PUMP DRIVEBELT
36. Reinstall the AC compressor drive belts.
37. Install alternator
#069891.
brackets
#069890
and
Note: Install the upper bracket #069891 with
short end towards bumper and long end towards turbo.
Use:
4x cap screws #5001308
Apply blue Loctite
Tighten to 48 lb-ft
FIGURE 41
Writer: EL

IS-19910E
Page 30 / 74
38. Installing the LH alternator pulley. Place
#560720 alternator flat on a bench with the
shaft horizontal.
Required tools:
•
•
15-16” crowfoot adapter
8mm hex bit
Clean shaft and pulley with brake cleaner.
Slide pulley #069893 on shaft by hand.
Hand thread nut on shaft until snug.
Using thin wall15/16”adapter and 8mm hex bit
to block shaft rotation, tighten to 70-80 lbf-ft.
Never use power tools to install pulley and nut.
FIGURE 42
Note: Do not apply any pressure to end of the
shaft. Internal damage may occur if the shaft is
pushed back and turned.
39. Install alternator on support with four (4)
#5002091 M10x120 screws.
Apply blue Loctite
Tighten to 48 lb-ft
FIGURE 43
40. Install the idler support #011213 using:
3x screws #5001799
Tighten to 48 lb-ft
FIGURE 44
Writer: EL

IS-19910E
Page 31 / 74
41. Install the new idler #012349 with screw
#5001786 and washer #5002008.
Tighten to 59 lb-ft
FIGURE 45
42. Install the dust cap #453076.
FIGURE 46
FIGURE 47
Writer: EL

IS-19910E
Page 32 / 74
43. Install the new alternator tensioner #510991.
Secure with one screw #5001799 on which
blue Loctite is applied.
FIGURE 48: Tensioner mounting screw torque : 48 lb-ft
44. Install belt #506067. To do so, rotate the
automatic belt tensioner using a ½ square drive
breaker bar.
FIGURE 49
45. Remove former belt routing decal and replace
with decal #010111.
FIGURE 50
Writer: EL

IS-19910E
Page 33 / 74
46. Install control harness #0610037 on alternator.
Connect circuit I to Indicator (I) post.
Connect circuit S to Sense (S) post.
Use the following hardware:
•
•
2x nylon lock nut #5001180
2x washer #5001137
Tighten to the following torque values:
Sense (S): 25-45 lb-in
Indicator (I): 25-45 lb-in
Apply Color Guard Rubber Coating on the
connections.
FIGURE 51
FIGURE 52
47. Perform the “Multiplex Modules Disconnection
Procedure Prior to Welding” found in your
vehicle Maintenance Manual, Section 00:
General.
48. Weld the new coolant filter support #050265 on
the engine cradle.
23 ½ inches from the end of the cradle
FIGURE 53
Writer: EL

IS-19910E
Page 34 / 74
FIGURE 54
FIGURE 55
FIGURE 56
Writer: EL

IS-19910E
Page 35 / 74
49. As a preparation to welding, buff the paint to
reach bare metal. Weld the ground stud
#380360 centered in the beam and at 14
inches from the beam end.
FIGURE 57
FIGURE 58: GROUND STUD #380360
50. Apply black paint to the area surrounding the
ground stud and also on the ground stud
circular base. DO NOT apply paint on the
electrical contact surfaces.
FIGURE 59: GROUND STUD #380360
51. Install a tie mount #504013 with one screw
#502686 at the back of the L.H. engine mount.
FIGURE 60
Writer: EL

IS-19910E
Page 36 / 74
52. Install the alternator ground cable #0610035.
Use the ground screw and lock washer
supplied with alternator with the addition of a
flat washer #500411.
torque: 50-60 lbf-in
53. Secure the alternator ground cable to the
previously installed tie mount using one (1)
nylon tie #509491.
FIGURE 61
FIGURE 62
54. Secure the alternator ground cable to the
previously installed ground stud on the L.H.
engine mount.
Use screw #502719 & washer #5001935
Tighten to 20 lbf-ft
Protection against corrosion. Apply Color
Guard rubber coating on the ground stud
once the ground cable is hooked up.
FIGURE 63
55. To the previously installed coolant filter
support, install the filter holder recovered from
the former installation.
FIGURE 64
56. Install the new coolant filter onto the filter
holder. Check the clearance between the filter
and the close hose clamps of the coolant pipe
leading to the transmission oil cooler.
Writer: EL

IS-19910E
Page 37 / 74
57. Transfer the drain plug and the coolant
extractor quick connect fitting saved from the
old pump inlet pipe.
Apply Loctite 567 Thread
installation of the fittings
Sealant
prior
58. Install the new radiator outlet pipe #050288.
Reinstall with the flexible hose #053617 and
the four (4) hose clamps #992089. Use steel
wire to hold the end of the pipe until the
radiator is installed if required.
A: # 992089 hose clamp (4x)torque: 30 lbf-in
FIGURE 65
B: drain plug
C: coolant extractor quick connect valve
D: # 053617 silicone hose
59. Reinstall the elbow between the copper heater
line and the new radiator outlet pipe.
For proper clamp torque, refer to HOSE CLAMP
TORQUE on page 12.
FIGURE 66
60. Using blue flexible hose #052366, prepare two
new short hoses for the coolant filter.
a) Cut two sections of blue flexible hose, one 22
inches long and a second 38 inches long.
A : hose clamp #992081 (4x)
B: banjo fitting copper washer #507657 (6x)
FIGURE 67
b) Use the banjo fittings recovered from the
previous installation.
hose clamp torque: 30 lbf-in
FIGURE 68
Writer: EL

IS-19910E
Page 38 / 74
61. Install the 22” long and 38” long hoses
prepared at the previous step as shown on the
images.
FIGURE 69
FIGURE 70
62. Connect the DEF injector coolant line return
hose to the radiator outlet pipe.
Use two (2) new banjo fitting copper washer
#507657
FIGURE 71: DEF INJECTOR COOLANT LINE RETURN HOSE
Writer: EL

IS-19910E
Page 39 / 74
63. Connect the coolant line coming from the surge
tank to the radiator outlet pipe.
TORQUES:
Constant-Torque with spring washers clamps :
90-100 lbf-in
Oetiker clamps – green spring : 12-18 lbf-in
FIGURE 72
Oetiker clamps – unpainted spring : 8-9 lbf-in
Caillau clamps : 30 lbf-in
64. Secure the coolant hoses together using nylon
ties.
A : handcuff nylon tie #N37749 (3x)
FIGURE 73
FIGURE 74
Writer: EL

IS-19910E
Page 40 / 74
65. Secure the coolant hose near the engine block
«push-lok» fitting as shown.
B : nylon tie #504016 (1x)
FIGURE 75
Writer: EL

IS-19910E
Page 41 / 74
66. Hook up the “L.H. alternator power cable”
#234524934 to the alternator positive (+) post.
Place the flash washer between the cable lug
and the nut.
1x nut #500685
torque: 80-125 lbf-in
1x flat washer #5001341
Apply Color Guard rubber coating at the alternator
ground (
) and positive (+) connections.
IMPORTANT NOTE
FIGURE 76
Early alternators are provided with a shorter positive stud.
With the short stud, nut #500685 does not thread
fully to allow the locking nylon insert to grip on the
threads.
In this case, DO NOT use nut #500685. Use the
nut and lock washer provided with the alternator
instead. Tighten to: 80-125 lb-po (9.0-14.0 N-m).
FIGURE 77:
Writer: EL
-
NUT #500685 DOES NOT THREAD FULLY TO ALLOW
THE LOCKING NYLON INSERT TO GRIP ON THE
THREADS (UPPER IMAGE)
-
HARDWARE TO USE WITH SHORT STUD (LOWER
IMAGE)

IS-19910E
Page 42 / 74
67. Connect the “fan drive ground cable” #069246
to the ground stud previously welded to the
chassis.
A: split lock washer #500482
B: brass nut #500998
C: fan drive ground cable #069246
FIGURE 78
FIGURE 79
68. Apply Color Guard rubber coating on the
ground stud connection.
FIGURE 80: GROUND STUD WITH RUBBER COATING
Writer: EL

IS-19910E
Page 43 / 74
69. Install a tie mount #509490 at the location
shown on the picture. Secure the tie mount
with a rivet.
A: tie mount #509490
B: rivet #504610 (hole diameter: Ø 17/64)
C: nylon tie #509491
D: fan drive power cable #23498721
FIGURE 81
70. Secure the “fan drive power cable” #23498721
onto the tie mount using a nylon tie. Make sure
to leave 26 inches long from the tie mount up
to the end of the “fan drive power cable” red
connector.
FIGURE 82
FIGURE 83
FIGURE 84
71. Install six (6) tie mounts to secure the “fan
drive power cable” and the “L.H. alternator
power cable” as shown on the picture.
Writer: EL

IS-19910E
Page 44 / 74
FIGURE 85
A: tie mount #509490
B: rivet #504610
C: nylon tie #509491
FIGURE 86
72. Route the “fan drive power cable” and the
“L.H. alternator power cable” up to the main
power compartment. Refer to the pictures at
right as a guide for the installation.
73. Secure both cables using seven (5) tie
mounts #509490 fixed with seven (5) rivets
#504610 (hole diameter: Ø 17/64). Secure the
cables on the tie mounts as previously done
with fourteen (10) nylon ties # 509491.
A: tie mount #509490
B: rivet #504610 (hole diameter: Ø 17/64)
C: nylon tie #509491
Writer: EL
FIGURE 87

IS-19910E
Page 45 / 74
FIGURE 88
Writer: EL

IS-19910E
Page 46 / 74
74. INSTALLATION OF THE “FAN TO RJB
INTERFACE” HARNESS #23488790
a) Route the “fan to RJB interface” harness
#23488790 up to the main power
compartment. Secure this harness to the
fan drive power cable using nylon ties
#504016.
b) This harness will be connected close to the
fan drive power cable, thus it also requires
26 inches of free length.
FIGURE 89
A: FAN TO RJB INTERFACE” HARNESS #23488790
B: FAN DRIVE POWER CABLE
C: NYLON TIES #504016 (23x approx.)
FIGURE 90
FIGURE 91
FIGURE 92
Writer: EL

IS-19910E
Page 47 / 74
75. Connect the new CAC outlet pipe #050406 to
the engine intake elbow. NOTE: in case of
interference between this pipe and the ping
tank, rotate the ping tank.
A: #030096 hose (1x)
B: #21490630 spring loaded clamp (2X) (torque:
5 lbf-ft)
FIGURE 93
FIGURE 94: CONNECTION AT THE ENGINE INTAKE ELBOW
FIGURE 95
Writer: EL

IS-19910E
Page 48 / 74
76. If your vehicle is equipped with AFSS
(Automatic Fire Suppression System), the new
CAC outlet pipe #050406 is likely to come into
interference with a AFSS extinguishing agent
hose (see image) near the end of the pipe that
connects with the Charge Air Cooler.
If this is the case, move the hose the other side
of the bracket shown, to prevent rubbing
between the hose and the CAC outlet pipe.
FIGURE 96
77. On the diagonal member, change the existing
radiator inlet pipe bracket for the new one
#050305. Use the existing hardware.
FIGURE 97
78. Install the new radiator inlet pipe #050414.
A: #052889 silicone hose
B: # 992089 hose clamp (4x), torque: 30 lbf-in
FIGURE 98
Writer: EL

IS-19910E
Page 49 / 74
79. Install the new CAC inlet pipe #050286. Use
one new #030096 CAC flexible hose. Secure
the hose using two (2) spring loaded clamps
#21490630.
A: #030096 hose
B: #21490630 spring loaded clamp (2X), torque:
5 lbf-ft
FIGURE 99: CONNECTION AT THE TURBO OUTLET ELBOW
80. Reinstall the cooling pack.
FIGURE 100
81. Secure the cooling pack base with the following
parts:
A: 4x screw #502804
B: 8x washer #5001751
C: 4x nut #502859
FIGURE 101
Writer: EL

IS-19910E
Page 50 / 74
82. In case of interference between the charge air
cooler and the DPF inlet pipe, loosen the pipe’s
V-band clamps. Move the pipe in order to
increase the clearance, then hold the pipe in
place and tighten the V-band clamps.
FIGURE 102
FIGURE 103
83. Using parts #501332, #501308, #501329,
#501027, mount the brass fitting assembly
shown on the image at right.
Apply Loctite 567 Thread Sealant on the
threads
A: #501027
B: #501329
C: #501308
D: #501332
FIGURE 104: BRASS FITTING ASSEMBLY
84. Remove the vent hose fitting found on the
radiator.
FIGURE 105
Writer: EL

IS-19910E
Page 51 / 74
85.
Install the brass fitting assembly in place of
the former vent hose fitting and then connect
the radiator vent hose to the radiator.
86. Prepare the cooling pack upper attachment
with the three (3) rectangular plates (see
image) recovered from the former installation
and the following parts:
A: anti-vibration mount #21185073
B: upper radiator support #050214
C: 2x screw #5001738 , 2x nut #502837
D: 2x screw #5001738 , 2x washer #500942
E: 2x screw #5001745 , 2x washer #500942
FIGURE 106
One end of the upper attachment is
mounted on the radiator frame (image at
right)
FIGURE 107
Bolt the anti-vibration mount onto the
vehicle chassis
FIGURE 108
Writer: EL

IS-19910E
Page 52 / 74
87. Reinstall all the blue flexible hoses at the CAC
and radiator (at the lower connections of the
cooling pack). Install with the following parts:
A: #21490616 clamp (4x) (torque: 5 lbf-ft)
B: #531471 flexible hose
C: #053617 silicone hose
D: #992089 (4x)
FIGURE 109
88. Reinstall all the blue flexible hoses at the CAC
and radiator (at the upper connections of the
cooling pack). Use the following parts::
A: 1x flex hose #531469
B: 1x silicone hose #053617
C: 4x clamp #21490616 (torque: 5 lbf-ft)
D: 4x clamp #992089
FIGURE 110
For proper clamp torque, refer to HOSE CLAMP
TORQUE on page 12
89.
Reinstall the lower cooling pack protector
tube with the following hardware:
4x Screw #502804
4x split lock washer #5001737
FIGURE 111
Writer: EL

IS-19910E
Page 53 / 74
90.
Install the sealing element #050200. Screw it
on the existing threaded holes on the upper
part of the radiator. Secure with the following
hardware:
6x bolt #5001697
6x lock washer #502570
FIGURE 112
FIGURE 113
91.
Install the sealing element #050203. Screw it
on the existing threaded holes on the bottom
of the radiator. Secure with the following
hardware:
6x bolt #5001697
6x lock washer #502570
FIGURE 114
92.
Prepare the sealing elements #050201 and
#050202. On both parts, apply foam tape
#506040 on the edges as shown on the
image.
FIGURE 115
Writer: EL

IS-19910E
Page 54 / 74
93.
Install the sealing elements #050201 and
#050202. Screw them onto the upper and
lower sealing elements installed at the
previous steps. Secure with the following
hardware:
8x bolt #5001697
8x lock washer #502570
A: #050201
B: #050202
FIGURE 116
94.
Cut two pieces of 39 inches (990 mm) long
of rubber extrusion #506025.
95.
Using good industrial glue (Loctite 404 or
similar product), glue the two pieces of
rubber
extrusion
centered
on
the
reinforcement angles of fan support panel
#050195.
FIGURE 117
FIGURE 118
Writer: EL

IS-19910E
Page 55 / 74
96.
Install the fan support panel #050195.
Secure with the following hardware:
19x bolt #5001697
19x lock washer #502570
FIGURE 119
97.
Install the upper left #050204 and upper right
#050206 sealing elements.
Secure with the following hardware:
6x bolt #5001697
6x lock washer #502570
FIGURE 120
98.
Install the lower sealing element #050213.
Secure with the following hardware:
5x bolt #5001697
5x lock washer #502570
FIGURE 121
99.
Install the
#050208.
L.H.
side
sealing
element
Secure with the following hardware:
4 bolts #5001697
4 lock washers #502570
FIGURE 122
Writer: EL

IS-19910E
Page 56 / 74
100. Install the
#050255.
R.H.
side
sealing
element
Secure with the following hardware:
4x bolt #5001697
4x lock washer #502570
FIGURE 123
101. With a paint marker, identify the fans from 1
to 8 with the corresponding number found on
a label on their respective blue connector.
102. Install the fans and fan hand guards on the
panel in the same arrangement shown on
the image. Be sure to place the fan so that
the cable is at the proper location, 3
O’clock, 6 O’clock or 12 O’clock. Refer to the
image at right.
FAN HAND GUARD
FIGURE 124
Install with the following hardware:
32x bolts #502686
32x lock washers #5001833
Prescribed torque:30 lbf-in
Writer: EL

IS-19910E
Page 57 / 74
103. Snap the fan blue connector in the holes
punches on the panel for that matter.
FIGURE 125
104. Route and secure the fan cables as shown
on the images.
Secure with the following parts:
A= nylon tie mount #504013 + rivet
#504379 + nylon tie #504016
B= nylon tie #504016
Do not tighten the nylon ties at this moment
FIGURE 126
Writer: EL

IS-19910E
Page 58 / 74
FIGURE 127
105. Install the circuit breaker box #564512.
Install with the following hardware:
4x bolt #500119
4x lock washer #5001868
FIGURE 128
A: 2x bolt #500119 + 2x lock washer #5001868
FIGURE 129
A: 2x bolt #500119 + 2x lock washer #5001868
Writer: EL

IS-19910E
Page 59 / 74
106. Connect each fan to the corresponding
connection port on the circuit breaker box.
FIGURE 130
107. Tighten the nylon ties previously installed
while routing the fan cables.
108. Use two (2) additional nylon ties #504016 to
secure the extra-length of cables together
close to the circuit breaker box as shown on
the image at right.
FIGURE 131
109. Install the electrical connector cover #
050229.
Fasten with the following hardware:
4x bolt #5001697
4x lock washer #502570
110. Using good industrial glue (Loctite 404 or
similar product), glue three (3) pieces of
rubber extrusion #506025 as shown on the
connector cover.
FIGURE 132
Writer: EL

IS-19910E
Page 60 / 74
FIGURE 133
111. Complete the installation of the sealing
elements. Screw the panels to the chassis
threaded holes where shown on the image.
Use the following hardware:
22x bolt #502848
FIGURE 134
112. Complete the connection of the cables and
harness to the fan circuit breakers box (three
connectors: gray, black, red).
A: fan drive ground cable (black connector)
B: fan drive power cable (red connector)
C: “fan to RJB interface” harness (gray
connector)
FIGURE 135
Writer: EL

IS-19910E
Page 61 / 74
113. Secure the fan drive ground cable and the
fan drive power cable connected to the fan
drive circuit breakers box as shown on the
pictures.
A: rivet #504379 (6x) (hole diameter: Ø 13/64)
B:tie mount #504013 (6x)
C:nylon tie #504016 (6x)
D: handcuff nylon tie #N37749 (1x)
FIGURE 136
FIGURE 137
114. Connect the alternator control harness
connector C-ALT3 to connector C-ALT3 of
the “fan to RJB interface” harness. Secure
the extra length of harness as shown with
nylon ties.
A: handcuff nylon tie #N37749 (3x)
B:nylon tie #504016 (4x)
FIGURE 138
FIGURE 139
INSTALLATION OF ELECTRIC COMPONENTS AND HARNESS
CONNECTIONS IN THE MAIN POWER COMPARTMENT
Writer: EL

IS-19910E
Page 62 / 74
SCHEMATIC DIAGRAM OF ELECTRICAL CABLES & HARNESSES
Writer: EL

IS-19910E
Page 63 / 74
115. In the battery compartment, disconnect the
battery ground cable from the chassis
ground stud.
116. Most of the electric components will be
installed on the bulkhead at the right of
master relay R1 (when facing it). Identify the
master relay R1 on the image at right.
FIGURE 140
117. If the situation applies to the vehicle on
which you are working on, remove the two
(2) useless studs found on the bulkhead and
then sand to leave a smooth surface.
FIGURE 141
Writer: EL

IS-19910E
Page 64 / 74
FIGURE 142
118. Make sure this is no voltage at the master
relay R1 posts and then, remove the master
relay R1 cover.
FIGURE 143
119. Disconnect the four (4) cable lugs connected
to the master relay R1 upper post.
120. Momentarily, connect the elbowed lug of the
“master relay R1 to 300A fuse” cable
#23498450.
FIGURE 144
121. Find the best location where to install the
fuse holder #563750 on the bulkhead. Take
note that the fuse holder must be installed at
the distance that allows cable #23498450 to
reach it.
122. Drill two 11/64 pilot holes for the installation
of the fuse holder on the main power
compartment bulkhead. Secure with the
following hardware:
A: tapping screws #500658 (2x) + flat
washer #5001341 (2x)
FIGURE 145
Writer: EL

IS-19910E
Page 65 / 74
123. Reinstall the four (4) other cable lugs to the
master relay R1 upper post.
Being the largest lug at R1, the cable #23498450
lug should be placed first on the post (behind
all the other lugs) (or second if rubbing is likely
to happen).
Master relay R1- Port 30 – M10-1.5 stud nut
torque: 160-195 lb-in (18-22 Nm)
FIGURE 146: ON THIS PICTURE, CABLE #23498450 LUG IS
IN SECOND (2ND) POSITION BECAUSE IT WAS LIKELY TO
RUB ON THE HEAD OF ONE OF THE FOUR SCREWS.
124. Reinstall the master relay R1 cover.
FIGURE 147
125. Place the 300A fuse #564520 in the fuse
holder underneath the cable lugs.
126. Connect to the free post of the fuse holder
the two (2) following cables that are routed
from the alternator and the fan drive circuit
breakers box:
•
•
Fan drive power cable #23498721
L.H. alternator power cable #23524934
A: nut #5001983 (2x)
B: washer #5001341 (2x)
Thread the nuts and tighten to a torque of 96
lbf-in (11Nm).
Writer: EL
FIGURE 148: TAKE NOTE THAT THE 300A FUSE IS NOT
PRESENT ON THE PICTURE ABOVE BUT IT SHOULD BE
INSTALLED AT THIS STEP

IS-19910E
Page 66 / 74
127. Secure the “fan drive power” cable and the
“L.H. alternator power” cable as shown on
the pictures at right using the following parts:
A: tie mount #509490 (2x)
B: rivet #504610 (2x) (hole diameter: Ø 17/64)
C:nylon tie #509491 (3x)
FIGURE 149
FIGURE 150
128. Install the MCM #23499009-EFD and the
I/O-B module #22722850 on the bulkhead.
•
•
Spacing between the I/O-B and the MCM=1
inch
Pilot holes diameter: 11/64”
Install with the following hardware:
Tapping screws #500658,
3x for the MCM
4x for the I/O-B module
FIGURE 151: MAIN POWER COMPARTMENT
Writer: EL

IS-19910E
Page 67 / 74
129. Depending on the coach configuration, an
existing mounting plate may extend where
the MCM should be installed and cause
interference. If this mounting plate useless,
cut it off along the red line shown on the
image.
IMPORTANT: Do not leave a sharp edge.
Smooth down the edge.
FIGURE 152
130. In the main power compartment, connect the
“fan to RJB interface harness” to the “MCM
to I/O-B interface harness” #23445869 by
means of connector C-EFD1.
131. Connect the MCM and the I/O-B module
together using the “MCM to I/O-B interface
harness” #23445869.
132. Connect the OEL resistors connector RES1F
and RES2F (part #563593) to the “MCM to
I/O-B interface harness”. See the image at
right and the following pictures for reference.
FIGURE 153
Writer: EL

IS-19910E
Page 68 / 74
FIGURE 154
A:nylon tie #504016 (3x)
FIGURE 155
A:nylon tie #504016 (2x)
FIGURE 156
A:nylon tie #504016 (3x)
B:nylon tie #509491 (2x)
C:swivel mount #504751 (1x)
Writer: EL
FIGURE 157
B:nylon tie #509491 (2x)
C:swivel mount #504751 (1x)

IS-19910E
Page 69 / 74
133. In the main power compartment, connect the
“vehicle interface harness” #23490553 to
the “MCM to I/O-B interface harness” by
means of connector C-EFD2.
FIGURE 158
134. Connect circuit 24VI, 24VD & GND2 to post
1, 2 & 5 respectively of the junction block.
FIGURE 159
135. Get the J1939 signal. To do so, locate
connector C193 among the existing
harnesses in the main power compartment.
136. Disconnect connector C193 and connect
with C193FS and C193FP of the “vehicle
interface harness” #23490553.
FIGURE 160
Writer: EL

IS-19910E
Page 70 / 74
137. In the main power compartment, locate I/O-B
module A52 (alternately named AE52).
138. At A52 (or AE52), remove existing circuit 291
and 292 from connector J1:1 (pin 1) and J1:2
(pin 2).
139. For each circuit, cut the terminal and put a
heat shrinking sleeve at the end of the wire.
Those circuits won’t be used anymore.
140. Insert circuit 291 and 292 of the “vehicle
interface
harness”
#23490553
into
connector J1 pin 1 and J1 pin 2 respectively.
FIGURE 161
141. On the bulkhead, install the alternator
telltale bracket #050303. Fasten to the
bulkhead using two (2) rivets #504379 (hole
diameter: Ø 13/64).
142. Place the alternator telltale insert #391028
in the telltale light module #562113.
143. Connect the appropriate branch of the “fan to
RJB interface harness” to the telltale light
module.
FIGURE 162
FIGURE 163
Writer: EL

IS-19910E
Page 71 / 74
FIGURE 164
144. There are remaining nylon ties and tie
mounts in the kit. Use them to secure the
harnesses and cables that may seem loose.
The goal is to prevent rubbing of the cables
and harnesses.
FIGURE 165
145. Install one (1) warning decal #069205 as
shown on the image.
FIGURE 166
Writer: EL

IS-19910E
Page 72 / 74
146. Install a second warning decal #069205 as
shown on the radiator door.
FIGURE 167
147. Fasten the
assembly.
radiator
door
upper
arm
FIGURE 168
148. Refill the cooling system. Connect coolant
extractor. Use coolant extractor to refill the
coolant from the engine.
FIGURE 169
Writer: EL

IS-19910E
Page 73 / 74
149. Reinstall the rear bumper.
FIGURE 170
150. Reinstall the access panel located behind
tag axle L.H. side wheel.
FIGURE 171
151. Reinstall L.H. side rear fender.
FIGURE 172
Writer: EL

IS-19910E
Page 74 / 74
152. In the battery compartment, connect the
battery ground cable to the chassis ground
stud.
FIGURE 173
153. In the main power compartment, set the
battery master switch to the ON position.
154. Set the ignition switch to the ON position.
155. In the main power compartment, reset the
circuit breakers and wait two (2) minutes for
the new installer I/O-B module to be
programed.
SYSTEM TEST
156. Start the engine to idle.
157. With the engine in idle (600 rpm), use the
Diagnostics menu of the Driver Information Display
to engage the fans in speed 1.
Diagnostics > Vehicle Tests > Activate Radiator FAN Speed 1
The height (8) fans should run at 50% of the maximum
speed. You need to evaluate the sound level and the
power of the air stream to determine the speed.
158. Engage the fans in speed 2.
Diagnostics > Vehicle Tests > Activate Radiator FAN Speed 2
The eight (8) fans should run at 75% of the maximum
speed.
159. Set the engine to the fast idle, the fans should then
engage at 100% of the maximum speed.
160. If the fans behave in accordance with the criterions
of the previous steps, then they operate normally.
PARTS / WASTE DISPOSAL
Discard waste according to applicable environmental regulations (Municipal/State[Prov.]/
Federal)
Writer: EL