S-SB-0006-12 Rev

S-SB-0006-12
Rev2
May 3, 2012
Smart Key System Check During PDS
Service
Category
General
Section
Pre-Delivery Service
Market
USA
Applicability
YEAR(S)
MODEL(S)
2013 – 2014
FR-S, tC
ADDITIONAL INFORMATION
REVISION NOTICE
May 9, 2013 Rev2:
• Applicability has been updated to include 2014 model year FR-S and tC vehicles.
April 23, 2013 Rev1:
• Applicability has been updated to include 2013 model year FR-S vehicles.
Any previous printed versions of this bulletin should be discarded.
Introduction
Some 2013 – 2014 model year vehicles are equipped with a Smart Key system, which allows the
customer to enter and start the vehicle without using a mechanical key. To ensure the system is
operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected
using the following procedure during Pre-Delivery Service (PDS).
NOTE
Check ALL of the Smart Keys using this procedure.
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
–
–
–
–
© 2013 Toyota Motor Sales, USA
Page 1 of 4
Rev2
S-SB-0006-12
May 3, 2012
Page 2 of 4
Smart Key System Check During PDS
Inspection Procedure
1. Remove ALL Smart Keys from the vehicle.
NOTE
The remaining keys need to be a minimum of 3 feet (1 meter) away from the vehicle.
2. Check Smart Entry function at all the doors.
NOTE
Smart Key MUST be in actuation area No. 1 for this check (see Figure 1 below).
Figure 1.
1
1
2
1
1
1
Actuation Area No. 1
2
Actuation Area No. 2
A. Locking function:
Push the lock button on the outside door handle. All the doors should lock simultaneously.
At this time, one beep will be heard and the turn signal lights will flash once.
© 2013 Toyota Motor Sales, USA
Rev2
S-SB-0006-12
May 3, 2012
Page 3 of 4
Smart Key System Check During PDS
Inspection Procedure (Continued)
B. Unlocking function:
NOTE
After checking the lock function, wait at LEAST 3 seconds before checking the unlock
function.
Grasp the outside door handle (sensors are located on the underside of the door handles).
At this time, two beeps will be heard and the turn signal lights will flash twice.
NOTE
Only the driver’s door unlocks when the driver’s door handle is grasped. All the doors
unlock when any door handle other than the driver’s door handle is grasped.
3. Check the Wireless Door Lock function.
Using the remote outside of the vehicle, confirm that all doors can be locked and unlocked
using the wireless remote.
4. Check Smart Start function from inside the vehicle.
NOTE
Smart Key MUST be in actuation area No. 2 for this check (see Figure 2).
Figure 2.
1
1
2
1
1
Actuation Area No. 1
1
2
Actuation Area No. 2
A. Check for proper activation of the “ENGINE START/STOP” switch.
(1) Make sure the gear selector lever is in the “P” position.
© 2013 Toyota Motor Sales, USA
S-SB-0006-12
Rev2
May 3, 2012
Page 4 of 4
Smart Key System Check During PDS
Inspection Procedure (Continued)
(2) Without depressing the brake pedal,
press the “ENGINE START/STOP” switch
and confirm the mode changes properly.
From the “OFF” mode:
Figure 3. Engine Start/Stop Switch
• Press once. The power supply mode
is in the “ACC” mode.
• Press twice. The power supply
mode is in the “IG-ON” mode.
1
2
2
• Press three times. The power supply
mode is in the “OFF” mode.
NOTE
If the “ENGINE START/STOP” switch
illuminator blinks in amber, refer to
the Repair Manual.
1
Light Off
2
Light On
B. Check the engine start/stop function.
(1) Make sure that the gear selector lever is in the “P” position.
(2) When depressing the brake pedal, check that the green engine switch illuminator
comes on, and push the “ENGINE START/STOP” switch to start the engine.
(3) Push the switch again to stop the engine.
NOTE
When the “ENGINE START/STOP” switch is turned OFF with the gear selector lever in a
position other than “P,” the vehicle electrical system will be in the “ACC” mode. When
the door is opened the Smart Key System Warning Buzzer will sound indicating that the
electrical system is not “OFF” when exiting the vehicle. This may result in a discharged
battery. Be sure to turn OFF the engine AFTER shifting the gear selector lever to the “P”
position.
Checking Procedure:
• Shift the gear selector lever to the “P” position (or check that the gear selector lever
is in the “P” position).
• Press the Engine Start/Stop switch once and check that the indicator light goes OFF.
5. Repeat steps 2 – 4 with each Smart Key.
© 2013 Toyota Motor Sales, USA