S-SB-0037-13

xB
01 Install Short Pin (see page 2) ..........................................
FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse;
turn on lights and rear defogger. Unlock doors; release fuel door.
01
02
03
04
05
06
07
08
09
Check dome, courtesy, map, and sun visor lights* .........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals, dimmer
switch, emergency flashers, and brake lights ..................
Check inside/outside rear view mirror operation/
adjustment .......................................................................
Check cigarette lighter* and power outlets* .....................
Check audio/navigation* systems, set SSP to xB, and
set clock ...........................................................................
Install shift-lock override button cover .............................
Check Rear Seat Entertainment System operation* .......
WALKAROUND INSPECTION
Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.
01 Check power window operation .......................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ...............
03 Check that engine starts with all keys ..............................
04 Check that child safety door locks are in normal
(unlocked) position* .........................................................
05 Check seats and seat belt operation ................................
06 Check rear defogger/rear view mirror defogger* ..............
07 Check side marker, tail, backup, and license plate lights.
08 Check luggage compartment light* & trim appearance ...
09 Adjust spare tire pressure, inspect for defects/damage,
and check jack and tool installation ................................
10 Check headlight aim ........................................................
UNDER HOOD
01
02
03
04
05
Check engine oil and ATM* fluid levels ...........................
Check brake and clutch* levels .......................................
Check engine coolant level .............................................
Check windshield washer fluid level ...............................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
* Inspect or install when equipped/required.
UNDER VEHICLE (ON HOIST)
OK
November 2013
Adjust/
Repair
OK
BEFORE INSPECTION
Adjust/
Repair
2014 PRE-DELIVERY SERVICE CHECK SHEET
01 Remove disc brake anti-corrosion wheel film*............
02 Inspect tires for defects/damage .....................................
03 Activate Tire Pressure Warning System (TPWS) (see
page 2) ............................................................................
04 Install wheel covers/caps/spare tire wheel covers* ..........
05 Inspect for fuel, oil, coolant, and other fluid leaks ............
06 Visually check bolts and nuts on chassis and powertrain
for looseness....................................................................
07 Inspect under the vehicle for damage, rust, etc. ..............
08 Install rubber body plugs (stored in glove box or center
center console) ...............................................................
ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Reading
Reading Before Test: _______________ Reading After Test: ________________
01
02
03
04
05
06
07
08
09
10
11
Check cold engine operation............................................
Check engine operation during warm-up .........................
Check engine at normal operating temperature ...............
Check clutch or transmission operation ...........................
Check brake and parking brake operation .......................
Check steering operation and off-center/vehicle
pull/flutter .........................................................................
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check front and rear* heater and A/C operation ..............
Check speedometer operation ........................................
Check cruise control operation* .......................................
FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) .......
02 Verify floor mat application and install using
retaining clips* ...............................................................
03 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
04 Remove Rapgard™ and clear protective bumper film* ....
05 Wash and clean vehicle ...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
08 Place oil change sticker on inside of windshield, top
left corner .........................................................................
09 Place Owner’s Guide and first aid kit portfolio*
in glove box .....................................................................
10 Install front license plate and mounting bracket* (see
page 2) ............................................................................
11 Perform Techstream Health Check .................................
Completion and retention of this from is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE
SERVICE MANAGER’S SIGNATURE
NAME (PLEASE PRINT)
NAME (PLEASE PRINT)
Date
Dealer Name
Dealer Code
We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)
SHORT PIN INSTALLATION
To minimize battery discharge the Short Pin has been removed
and is stored in the engine compartment Relay Block.
Install the Short Pin and confirm all related DTCs are cleared.
2
DTC Clearing Procedure
1.
2.
3.
4.
Connect Techstream.
Cycle the ignition switch to the “IG-ON” position.
Using Techstream, check any other codes being output.
Erase DTCs (B1650 & B1794) and Freeze Frame Data.
1
NOTE
If any DTCs besides B1650 & B1794 appear, repair the
applicable system according to the Repair Manual.
1 Remove This Short Pin
2 Install Short Pin Here
TPWS ACTIVATION & INITIALIZATION
Activation Procedure
1. Connect Techstream.
2. Cycle the ignition switch to the “IG-ON” position and
check that the Low Tire Pressure Warning Light
blinks for 1 minute and then remains illuminated.
3. Press or remove the valve core to reduce the tire
inflation pressure rapidly by 6 psi (0.4 kgf/cm²,
40 kPA), or more, within 30 seconds.
4. Check that the Low Tire Pressure Warning Light
goes OFF after all the TPWS sensors are activated.
5. Using Techstream, check for DTCs (C2111-C2114). If
no DTCs are stored, continue to Initialization procedure.
If these DTCs are stored, repeat step 3.
Initialization Procedure
Refer to the Repair Manual for the Initialization procedure.
Please note the spare tire does not have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is
significantly colder than shop temperature, perform a Health Check
using Techstream and select the “Compensation Tire Pressure”
checkbox. Compensation pressures will be displayed on the Health
Check results screen. Adjust the tire pressure when the tires are cold.
FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION*
For states that require a front license plate, please install per this procedure. The bracket and self-tapping screws are stored
in the luggage compartment.
Installation Procedure
1. Insert the front license plate into the mounting bracket
2. Attach the hooks of the mounting bracket to the upper lip of
the air intake and rotate the bracket upwards and hold
in place.
NOTE
The mounting bracket should snap securely onto
the bumper cover.
4. Align the installation holes on the mounting bracket and front
license plate with the dimples on the front bumper.
5. Screw in the 2 self-tapping screws directly into the dimples
to install the front license plate and mounting bracket.
NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.
2
4
3
3
4
2
1
1 Mounting Bracket
2 Hooks
3 Air Intake
4 Rotate Bracket
1
1 Self-tapping Screws
2 Dimples
3 License Plate
4 Mounting Bracket