A011856 2049142_
Service Bulletin Details
Public Details for: A011856 2049142_
- 2017 -
Models from 2017
2017 AUDI R8 |
2017 AUDI R8 SPYDER |
01 MIL on, DTC P243600 and/or P243700 stored in ECM 01 18 56 2049142/2 March 2, 2018. Supersedes Technical Service Bulletin Group 01 number 17-40 dated October 23, 2017 for reasons listed below. Model(s) Year VIN Range Vehicle-Specific Equipment R8, R8 Spyder 2017 000001 - 905000 Not Applicable Condition REVISION HISTORY Revision Date Purpose 2 - Revised Required Parts and Tools (Updated part number) 1 10/23/2017 Initial publication Customer statement: MIL on. Workshop findings: One or more of the following DTCs is logged in the engine control module (ECM), J623 (address word 0001): DTC P243600 (Secondary Air Injection System Air Flow/Pressure Bank 2 Sensor Circuit Range/Performance) And/or DTC P243700 (Secondary Air Injection System Air Flow/Pressure Bank 2 Sensor Circuit Low) According to the Guided Fault Finding, the differential pressure sensor Bank 2 (G610) has to be replaced. Technical Background Not applicable. Production Solution Not applicable. Page 1 of 4 © 2018 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Service 1. Replace the Differential pressure sensor Bank 2 (G610) according to the Repair Manual, Engine >> 24 Multiport fuel injection >> air filter housing, removing and installing >> 26 Exhaust System>Secondary Air System >> Combination valve, removing and installing >> Secondary air injection sensor G609/G610, removing and installing. 2. Then add the insulation (Figure 1, number 37) on the pressure sensor Bank 2. At the end of the repair the pressure sensor and the combination valve should have the insulation on both banks (Figure 2). Figure 1. Replace the sender. Page 2 of 4 © 2018 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Figure 2. Insulation on Bank 2 pressure sensor after installation. Tip: It is not necessary to receive a Repair Authorization to perform this or any other R8 TSB. Warranty Claim Type: 110 up to 48 Months/50,000 Miles. G10 for CPO Covered Vehicles – Verify Owner. If vehicle is outside any warranty, this Technical Service Bulletin is informational only. Service Number: 2675 Damage Code: 0040 Page 3 of 4 © 2018 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Labor Operations: Diagnostic Time: Claim Comment: Differential pressure sensor Bank 2 remove + reinstall 2675 1973 10 TU Air cleaner remove + reinstall Bank 2 (Coupe) 2425 1901 60 TU Air cleaner remove + reinstall Bank 2 (Spyder) 2425 1902 70 TU Install insulation wrap on pressure sensor Bank 2 2675 2499 20 TU GFF 0150 0000 Time stated on diagnostic protocol (Max 20 TU) Road test prior to service procedure No allowance 0 TU Road test after service procedure 0121 0004 10 TU As per TSB #2049142/2 All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. Required Parts and Tools Part Number Part Description Quantity 06L 906 052 Differential pressure sensor 01 079 133 105 B Heat insulation for Differential pressure sensor Bank 2 01 Additional Information All parts and service references provided in this TSB (2049142) are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information. Please check the Repair Manual for fasteners, bolts, nuts, and screws that require replacement during the repair. ©2018 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. Page 4 of 4 © 2018 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.