JTB00613NAS2

3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx
JTB00613NAS2
TECHNICAL BULLETIN
13 MAR 2018
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with
the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar
service facility to determine whether this bulletin applies to a specific vehicle.
INFORMATION
This reissue replaces all previous versions. Please destroy all previous versions.
Changes are highlighted in blue
SECTION:
501-08: Exterior Trim and Ornamentation
SUBJECT/CONCERN:
Rocker Panel Moulding/Rear Fender Paint Delamination
AFFECTED VEHICLE RANGE:
MODEL:
F-TYPE (X152)
MODEL YEAR:
2014 Onwards
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
VIN:
K00001 Onwards
ASSEMBLY PLANT:
Castle Bromwich
1/11
3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
Paint delamination may be evident between the rocker moulding panel and the rear fender.
CAUSE:
This may be caused by insufficient clearance between the rocker moulding panel and the rear fender.
ACTION:
Should a customer express this concern, follow the Workshop Procedure below.
PARTS:
NOTE:
* - an allowance ($3.75 USD or local equivalent) has been provided to cover the cost of the
adhesive tape (3M™ Acrylic Plus Tape PT1100 [8mm width or similar]) and cable tie. Claim using
Sundry Code ‘ZZZ001’.
PART NUMBER
ZZZ001
DESCRIPTION
Adhesive tape [8mm width]; cable tie
QUANTITY
$3.75
TOOLS:
Refer to Workshop Manual for any required special tools.
WARRANTY:
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
2/11
3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx
NOTE:
* - an allowance ($3.75 USD or local equivalent) has been provided to cover the cost of the
adhesive tape (3M™ Acrylic Plus Tape PT1100 [8mm width or similar]) and cable tie. Claim using
Sundry Code ‘ZZZ001’.
NOTES:
Repair procedures are under constant review, and therefore times are subject to change; those
quoted here must be taken as guidance only. Always refer to JLR claims submission system to
obtain the latest repair time.
The JLR Claims Submission System requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.
DESCRIPTION
SRO
TIME (HOURS)
CONDITION CODE
CAUSAL PART
Rocker panel moulding - Modification - Single
76.96.66
0.3
70
T2R10395
Rocker panel moulding - Modification - Pair
76.96.67
0.6
70
T2R10395
NOTE:
Normal Warranty procedures apply.
WORKSHOP PROCEDURE:
NOTE:
All illustrations: left-side shown; right-side similar.
1
Open the door on the side of the vehicle that has the concern.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
3/11
3/13/2018
2
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Remove the rear wheel arch liner fasteners.
3

Remove the door seal.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
4/11
3/13/2018
4
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Remove the fasteners.
5

Remove the trim.
Torque: 4 Nm
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
5/11
3/13/2018
6
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Remove the fasteners.
Torque: 4 Nm
7
CAUTION:
Do not use excessive force to reposition the rocker panel moulding; the rocker panel
moulding is still attached underneath the vehicle.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
6/11
3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Position the rocker panel moulding to one side.
8
NOTE:
A new cable tie must be used during installation.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
7/11
3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Cut and discard the cable tie.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
8/11
3/13/2018
9
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Clean the area shown.
10
NOTE:
The numbers shown correspond to the installation position in Step 11.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
9/11
3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Cut the adhesive tape to the sizes and quantities shown.
11
NOTE:
The position of the adhesive tape will vary depending on the contact point but the
measurement shown must always be correct.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
10/11
3/13/2018
JTB00613NAS2 - Rocker Panel Moulding/Rear Fender Paint Delamination | TOPIx

Install the adhesive tape to the areas of contact.
12
NOTES:
Make sure that no adhesive tape can be seen after installation.
The gap between the rocker panel moulding and the rear fender will be between 0.8-1.2
mm. This will reduce to 0.5 mm after 48 hours.
Reverse Steps 1-8.
13
NOTE:
Only if required.
Repeat steps 1-12 to the other side of the vehicle.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=887047
11/11