A18-018

Service Bulletin
18-018
May 9, 2018
Version 2
Capless Shutter Set (Mis-Fuel Inhibit Device) Is Frozen
Supersedes 18-018, dated March 16, 2018, to revise the sections highlighted in yellow.
AFFECTED VEHICLES
Year
Model
Trim
VIN Range
2016-18
Pilot
ALL
ALL
2017-18
Ridgeline
ALL
ALL
2018
Odyssey
ALL
ALL
REVISION SUMMARY
•
Odyssey information was added in AFFECTED VEHICLES, WARRANTY CLAIM INFORMATION, and PARTS
INFORMATION
•
REPAIR PROCEDURE - ODYSSEY was added
SYMPTOM
The customer is unable to insert the fuel nozzle into the filler neck and fuel the vehicle in cold weather.
PROBABLE CAUSE
Water or moisture has entered the fueling area and frozen the capless fuel shutter set in the fuel filler neck.
CORRECTIVE ACTION
Replace the capless shutter set. Install the fuel filler lid and apply the fuel filler caution label (if applicable).
CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Honda automobile dealer.
©
2018 American Honda Motor Co., Inc. — All Rights Reserved
Page 1 of 9
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation
Number
Description
3101U2
Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
Pilot: Replace the
0.7 hr
capless shutter set.
Install the fuel filler lid
cover and apply the fuel
filler caution label.
03214
03217
A18018A
17060-TG7-A01
3101U2
Ridgeline: Replace the 0.7 hr
capless shutter set.
Install the fuel filler lid
cover and apply the fuel
filler caution label.
03214
03217
A18018B
17060-TG7-A01
3101U2
Odyssey: Replace the
capless shutter set.
Install the fuel filler lid
striker and apply the
fuel filler caution label.
03214
03217
A18018C
17060-TG7-A01
0.7 hr
Skill Level: Repair Technician
PARTS INFORMATION
Part Name
Part Number
Quantity
Fuel Filler Caution Label (ALL)
17669-TG7-A01
1
Capless Shutter Set (Mis-Fuel Inhibit Device) (Pilot and
Ridgeline)
06160-TG7-A01
1
Capless Shutter Set (Mis-Fuel Inhibit Device)(Odyssey)
17671-TBA-A02
1
Fuel Filler Lid Striker (Odyssey)
74481-THR-A02
1
Fuel Filler Lid Cover (Pilot)
17667-TG7-A01
1
Fuel Filler Lid Cover (Ridgeline)
17667-T6Z-A01
1
Page 2 of 9
REPAIR PROCEDURE - PILOT
1. Remove the mis-fuel inhibit device by breaking the six lock tabs.
2. Pry up the lock tab, and remove the mis-fuel inhibit device.
NOTE
Be careful not to damage the fuel fill pipe or the main flap unit (fuel fill pipe top side surface); they do not need to be
replaced at this time.
3. Install the new mis-fuel inhibit device.
Page 3 of 9
4. Apply the fuel filler caution label to the new fuel filler lid cover as shown. Make sure the lid is clean and grease-free,
especially on the surface where the label will be applied.
5. Make sure the clamps engage the fuel fill door, then slide the lid cover away from the fuel fill door hinge. Press on
the lid until the clips snap into place. This indicates the lid is secured and correctly installed.
6. Make sure the fuel fill door closes and latches without contact or interference from the mis-fuel inhibit device and
surrounding area.
7. Make sure the fuel fill door release works correctly when using the fuel fill door release button.
Page 4 of 9
REPAIR PROCEDURE - RIDGELINE
1. Remove the mis-fuel inhibit device by prying out the four lock tabs and turning the assembly 90 degrees.
2. Tilt the mis-fuel inhibit device towards the rear of the vehicle to remove it from the fuel fill pipe.
NOTE
Be careful not to damage the fuel fill pipe or the main flap unit (fuel fill pipe top side surface); they do not need to be
replaced at this time.
3. Install the new mis-fuel inhibit device.
Page 5 of 9
4. Apply the fuel filler caution label to the new fuel filler lid as shown. Make sure the new lid is clean and grease-free,
especially on the surface where the label will be applied.
5. Make sure the clamps engage the fuel fill door, then slide the lid away from the fuel fill door hinge. Press on the lid
until the clips snap into place. This indicates the lid is secured and correctly installed.
6. Make sure the fuel fill door closes and latches without contact or interference from the mis-fuel inhibit device and
surrounding area.
7. Make sure the fuel fill door release works correctly when using the fuel fill door release button.
Page 6 of 9
REPAIR PROCEDURE - ODYSSEY
1. Remove the mis-fuel inhibit device by breaking the six lock tabs.
2. Pry up the lock tab, and remove the mis-fuel inhibit device.
NOTE
Be careful not to damage the fuel fill pipe or the main flap unit (fuel fill pipe top side surface); they do not need to be
replaced at this time.
3. Install the new mis-fuel inhibit device.
Page 7 of 9
4. Apply the fuel filler caution label to the new fuel filler lid striker as shown. Make sure the lid is clean and grease-free,
especially on the surface where the label will be applied.
5. Remove the original fuel filler lid striker. Lift the fuel filler lid locking tab and slide the lid upwards until the tabs
disengage from the slots in the fuel door.
6. Installation of the fuel filler lid striker is the reverse of removal. Verify all the tabs are engaged, and slide the lid
downwards until it clicks. This indicates the fuel filler lid striker is secured and correctly installed.
Page 8 of 9
7. Make sure the fuel door closes and latches without contact or interference from the mis-fuel inhibit device and
surrounding area. The gap between the door and the surrounding quarter panel should remain consistent.
8. Make sure the fuel fill door release works correctly when using the fuel fill door release button.
END
Page 9 of 9