H111 UPS3918-2BN

6/11/2018
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx
H111 UPS3918-2BNAS1
TECHNICAL BULLETIN
08 JUN 2018
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with
the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar
service facility to determine whether this bulletin applies to a specific vehicle.
INFORMATION
SECTION:
303-03B / -03C: Engine Cooling
SUBJECT/CONCERN:
Update Prior to Sale: Auxiliary Water Pump Inlet Hose Incorrectly Routed
AFFECTED VEHICLE RANGE:
MODEL:
MODEL YEAR:
VIN:
ASSEMBLY PLANT:
APPLICABILITY:
XE (X760)
2018
P16868-P40360
Castle Bromwich
V6 S/C 3.0L Petrol
XF (X260)
2018
Y53235-Y70993
Castle Bromwich
V6 S/C 3.0L Petrol
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
1/11
6/11/2018
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
This bulletin is being reissued to provide additional Parts, Warranty, and Workshop Procedure
information. Vehicles which previously did not pass the Inspection Procedure may now be
repaired.
SITUATION:
A potential issue has been identified on a limited number of vehicles within the listed Affected Vehicle
Range where the auxiliary water pump inlet hose may be routed incorrectly, allowing the hose to rub
against the Air Conditioning (A/C) compressor belt and cause markings on or damage to the hose and/or
possible coolant loss.
ACTION:
Retailers are required to HOLD affected new vehicles that are within your control and refrain from
releasing the vehicles for new vehicle sale pending completion of the Inspection Procedure, and if
necessary Workshop Procedure, detailed in this Technical Bulletin. Unsold vehicles should have this
performed as part of the Pre-Delivery Inspection (PDI) process but must have it completed prior to vehicle
handover to the customer.
This program does not apply to any vehicle already registered and in use, either with the retailer or
customer. Any vehicle already in use may continue to be driven and any repair instructions deemed
necessary will be communicated through a separate Field Action or Technical Bulletin.
PARTS:
NOTE:
Order only the expected percentage demand of parts identified.
DESCRIPTION
PART NO./SUNDRY CODE
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
QTY./VALUE
EXPECTED PERCENTAGE DEMAND
2/11
6/11/2018
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx
DESCRIPTION
Auxiliary water pump inlet hose
PART NO./SUNDRY CODE
QTY./VALUE
EXPECTED PERCENTAGE DEMAND
T4N18661
1
23%
SPECIAL TOOLS:
Refer to TOPIx Workshop Manual/Workshop Procedure for any required special tools.
WARRANTY:
NOTE:
Use the Jaguar Land Rover claims submission system to make sure that a vehicle is affected by this
program prior to undertaking any rework action.
At the time of confirming a booking for vehicle repair, make sure that all outstanding Recall and Service
Actions are identified to ensure the correct parts are available and adequate workshop time is allocated
for repairs to be completed at one visit.
Warranty claims must be submitted quoting the Program Code and the relevant Option Code; this will
result in payment of the stated time. The SRO and parts information is included for information only. The
Option Code(s) that allows for the drive in/drive out allowance may only be claimed if the vehicle is
brought back into the workshop for this action alone to be undertaken.
Repair procedures are under constant review and therefore times / prices are subject to change; those
quoted here must be taken as guidance only. Use the Jaguar Land Rover claims submission system to
obtain the latest repair time.
This program is valid for a limited time only. Warranty claims with a repair date prior to the 02 June 2019
closure date must be submitted or payment within 30 calendar days of completion of the repair.
PROGRAM
CODE
OPTION
CODE
H111
A
DESCRIPTION
SRO
Check the auxiliary water pump
inlet hose installation, no further
action
05.10.50
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
TIME
(HOURS)
PARTS/SUNDRY
CODE
QTY./VALUE
0.5
-
-
3/11
6/11/2018
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
SRO
TIME
(HOURS)
PARTS/SUNDRY
CODE
QTY./VALUE
H111
K
Check the auxiliary water pump
inlet hose installation, no further
action
Drive in /drive out
05.10.50
10.10.10
0.5
0.2
-
-
H111
B
Check and re-route the auxiliary
water pump inlet hose
26.91.19
1.1
-
-
H111
C
Check and re-route the auxiliary
water pump inlet hose
Drive in /drive out
26.91.19
10.10.10
1.1
0.2
-
-
H111
D
Auxiliary water pump inlet hose
- Renew
26.32.05
1.6
T4N18661
1
H111
E
Auxiliary water pump inlet hose
- Renew
Drive in /drive out
26.32.05
10.10.10
1.6
0.2
T4N18661
-
1
-
Normal Warranty policies and procedures apply.
INSPECTION PROCEDURE:
NOTE:
Some components in the illustrations have been removed for clarity.
1
Raise the vehicle on the ramp (see TOPIx Workshop Manual section 100-02: Jacking and Lifting Lifting).
2
Remove the air deflector (see TOPIx workshop Manual section 501-02: Front End Body Panels Air Deflector).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
4/11
6/11/2018
3
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx

Inspect the auxiliary water pump inlet hose.
If the auxiliary water pump inlet hose IS installed correctly (✓), go to Step 8.
If the auxiliary water pump inlet hose IS NOT installed correctly (✕) and the hose IS
NOT damaged, go to Step 4.
If the auxiliary water pump inlet hose IS NOT installed correctly (✕) and the hose IS
damaged, go to the Workshop Procedure below.
4
NOTE:
Retain the engine coolant.
Partially drain the engine cooling system (see TOPIx Workshop Manual section 303-03B / -03C:
Engine Cooling - Cooling System Partial Draining, Filling and Bleeding).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
5/11
6/11/2018
5
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx

Remove the transmission oil cooler hose fastener and move the oil transmission cooler hose to
the correct position.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
6/11
6/11/2018
6
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx

Install the transmission oil cooler hose in the correct position, making sure to secure the
transmission oil cooler hose fastener.
7
Fill and bleed the engine cooling system (see TOPIx Workshop Manual section 303-03: Engine
Cooling - Cooling System Partial Draining, Filling and Bleeding).
8
Install the air deflector (see TOPIx Workshop Manual section 501-02: Front End Body Panels - Air
Deflector).
9
Release the vehicle.
WORKSHOP PROCEDURE:
NOTE:
Some components in the illustrations have been removed for clarity.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
7/11
6/11/2018
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx
1
CAUTION:
Be prepared to collect and retain engine coolant.
Drain and retain the engine coolant (see TOPIx Workshop Manual section 303-03: Engine
Cooling - Cooling System Draining, Feeling and Bleeding).
2
Remove the front left wheel arch liner (see TOPIx Workshop Manual section 501-02: Front End
Body Panels - Front Wheel Arch Liner).
3
Remove the air cleaner outlet pipe T-Connector (see TOPIx Workshop Manual section 303-12:
Intake Air Distribution and Filtering - Air Cleaner Outlet Pipe T-Connector).
4
Remove the coolant expansion tank (see TOPIx Workshop Manual section 303-03: Engine
Cooling - Engine Expansion Tank).
5

Disconnect the auxiliary water pump inlet hose.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
8/11
6/11/2018
6
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx

Release the auxiliary water pump inlet hose connector.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
9/11
6/11/2018
7
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx

Release the clip and remove the auxiliary water pump inlet hose.
8
NOTE:
Make sure the hose is routed correctly (✓) as shown.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
10/11
6/11/2018
H111 UPS3918-2bNAS1 - Update Prior to Sale: Engine Coolant Hose Incorrectly Routed | TOPIx

Reverse Steps 5-7 to install the new auxiliary water pump inlet hose.
9
Install the coolant expansion tank (see TOPIx Workshop Manual section 303-03: Engine Cooling Engine Expansion Tank).
10
Install the air cleaner outlet pipe T-Connector (see TOPIx Workshop Manual section 303-12:
Intake Air Distribution and Filtering - Air Cleaner Outlet Pipe T-Connector).
11
Install the front left wheel arch liner (see TOPIx Workshop Manual section 501-02: Front End Body
Panels - Front Wheel Arch Liner).
12
Fill the engine coolant (see TOPIx Workshop Manual section 303-03: Engine Cooling - Cooling
System Draining, Feeling and Bleeding).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=901686
11/11