122-S4R2X-07

Service
Technical Information
38/18
ENU
9168
9
Symptom In Vehicle Interior - Outside Temperature Display Implausible: Reworking wire
harness for outside temperature sensor (SY 38/18)
Revisions:
Revision 1 — June 27, 2018
Changes/additions:
Part number corrected: 958.606.838.10
Model Year:
As of 2014 up to 2018
Model Line:
Macan (95B)
Subject:
Outside temperature sensor
Symptom:
The outside temperature display shows implausible values.
Cause:
The outside temperature display can show implausible values because the wire harness for the outside
temperature sensor is too long.
Remedial
Action:
In the event of a customer complaint, replace the outside temperature sensor and rework the the wire
harness using a clamp and tie-wrap.
Date of
Introduction:
The branch of the wire harness is adapted during production from model year 2019 onwards.
Parts Info:
958.606.838.10 – NEW –
Work Procedure: 1
 Tie-wrap holder
Preliminary work:
1.1
Remove front apron.
 Workshop Manual '631519 Removing and installing front apron'
1.2
Swivel flap of the air guide (right)  Air guide flap (right) -1- forward.
AfterSales
Jun 27, 2018
Page 1 of 3
9
Service
9168
ENU
Technical Information
38/18
Air guide flap (right)
Information
In the event of a complaint, also replace the outside temperature sensor.
 Workshop Manual '916819 Removing and installing outside temperature sensor'
2
Rework branch of wire harness for outside temperature sensor:
2.1
Secure tie-wrap holder  Branch of wire harness for outside temperature sensor -1- to the
right flap of the air guide as shown.
2.2
Secure electric line  Branch of wire harness for outside temperature sensor -2- for the
outside temperature sensor with a tie-wrap (958.606.838.10 –  Branch of wire harness
for outside temperature sensor -3-).
Branch of wire harness for outside
temperature sensor
3
Subsequent work:
3.1
Swivel flap of the air guide (right) back until it engages securely.
3.2
Install front apron.
 Workshop Manual '631519 Removing and installing front apron'
Jun 27, 2018
Page 2 of 3
AfterSales
Service
Technical Information
38/18
ENU
9168
9
End of action required.
Invoicing:
The work involved is invoiced under the labor operation:
APOS
Labor operation
91684900
Reworking outside temperature sensor
I No.
For invoicing and documentation using PQIS, enter the following coding:
Location (FES5)
91680
Outside temperature sensor
Damage type (SA4)
1613
Does not work at times
References:
 Workshop Manual '631519 Removing and installing front apron'
 Workshop Manual '916819 Removing and installing outside temperature sensor'
Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed.
© 2018 Porsche Cars North America, Inc.
AfterSales
Jun 27, 2018
Page 3 of 3