ITB18-028

Classification:
Reference:
Date:
EC18-025
ITB18-028
August 24, 2018
2019 QX50; MIL ON WITH DTC P0606
APPLIED VEHICLES: 2019 QX50 (J55)
IF YOU CONFIRM
The MIL is ON with DTC P0606 (CONTROL MODULE [control module processor]) stored.
ACTION
1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working
on.
2. If this bulletin applies, reprogram the ECM.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing.
You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to
successfully completing this repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that
a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this
applies to your vehicle.
1/10
SERVICE PROCEDURE
ECM REPROGRAMMING
IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

All CONSULT-III plus (C-III plus) software updates (if any) have been installed.

The CONSULT PC is connected to the Internet (Wi-Fi or cable).
NOTE:

Most instructions for reprogramming with C-III plus are displayed on the CONSULT PC screen.

If you are not familiar with the reprogramming procedure, click here. This will link you to the
"CONSULT- III plus (C-III plus) ECM Reprogramming" general procedure.

Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL)
conditions:
 Engine coolant temperature: 70 - 100°C
(158 - 212°F)
 Battery voltage: More than 12.9V (At idle)
 Transmission: Warmed up

After reprogramming is complete, you will be required
to perform Throttle Valve Closed Position, Idle Air
Volume Learn, Accelerator Closed Position, and DTC
erase.
Figure A
CAUTION:

Connect the GR8 to the 12V battery and select ECM Power Supply Mode.
If the vehicle battery voltage drops below 12.0V or above 15.5V during reprogramming, the ECM
may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted
and the ECM may be damaged.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the
CONSULT PC and the plus VI. If Bluetooth® signal waves are within range of the CONSULT PC
and plus VI during reprogramming, reprogramming may be interrupted and the ECM may be
damaged.
2/10
ITB18-028
1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.
2. Start C-III plus.
3. Wait for the plus VI to be recognized / connected.

The serial number will display when the plus VI is recognized / connected.
4. Select Re/programming, Configuration.
Step 3: plus VI
is recognized
Step
4
Figure 1
5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in Figure 2 on the next
page.
3/10
ITB18-028
6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).
6A: Current ECM P/N
Figure 2
B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number column in
Table A on the next page.

If there is a match, this bulletin applies. Continue with the reprogramming procedure.

If there is not a match, reprogramming does not apply. Refer to ASIST for further diagnosis.
4/10
ITB18-028
Table A
Model
Current ECM Part Number: 237105NL0A, 5NL0B, 5NL0C, 5NL0D
5NL1A, 5NL1B, 5NL1C, 5NL1D
5NL2A, 5NL2B, 5NL2C, 5NL2D
5NL3A, 5NL3B, 5NL3C, 5NL3D
2019 QX50
5NL4A, 5NL4B, 5NL4C, 5NL4D
5NL5A, 5NL5B, 5NL5C, 5NL5D
5NL6A, 5NL6B, 5NL6C, 5NL6D
5NL7A, 5NL7B, 5NL7C, 5NL7D
5NL8A, 5NL8B, 5NL8C, 5NL8D
5/10
ITB18-028
7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.
NOTE:

In some cases, more than one new P/N for reprogramming is available.
 In this case, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message “Caution! Use ONLY
with NTBXX-XXX”.

If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming
available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis.
Figure 3

Before reprogramming will start, you will be required to enter your User Name and Password.
 The CONSULT PC must be connected to the Internet (Wi-Fi or cable).
 If you do not know your Username and Password, contact your service manager.
Figure 4
6/10
ITB18-028
8. When the screen in Figure 5 displays, reprogramming is complete.
NOTE: If the screen in Figure 5 does not display (reprogramming does not complete), refer to the
information on page 8.
9. Disconnect the battery charger from the vehicle.
10. Select Next.
Step
10
Figure 5
NOTE:

In the next steps, starting on page 9, you will perform Throttle Valve Closed Position, Idle Air Volume
Learn, Accelerator Closed Position, and DTC erase.

These operations are required before C-III plus will provide the final reprogramming confirmation
report.
7/10
ITB18-028
ECM Recovery
Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete.
If reprogramming does not complete and the “!?” icon displays as shown in Figure 6:

Check battery voltage
(12.0 - 15.5 V).

Ignition is ON, engine OFF.

External Bluetooth® devices are
OFF.

All electrical loads are OFF.

Select retry and follow the on
screen instructions.

“Retry” may not go through on first
attempt and can be selected more
than once.
Figure 6
If reprogramming does not complete and the “X” icon displays as shown in Figure 7:

Check battery voltage
(12.0 - 15.5 V).

CONSULT A/C adapter is plugged
in.

Ignition is ON, engine OFF.

Transmission is in Park.

All C-III plus / VI cables are securely
connected.

All C-III plus updates are installed.

Select Home, and restart the
reprogram procedure from the
beginning.
Figure 7
8/10
ITB18-028
11. Follow the on-screen instructions to perform the following:

Throttle Valve Closed Position.

Idle Air Volume Learn (IAVL).
NOTE:
 Listed below are common conditions required for IAVL to complete.
 If IAVL does not complete within a few minutes, a condition may be out of range.
 Refer to the appropriate ESM for specific conditions required for the vehicle you are
working on.
o Engine coolant temperature: 70 - 100°C (158 - 212°F)
o Battery voltage: More than 12.9V (At idle)
o Selector lever: P or N
o Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
o Steering wheel: Neutral (Straight-ahead position)
o Vehicle speed: Stopped
o Transmission: Warmed up

Accelerator Pedal Close Position Learning

Erase DTCs
Continue to the next page.
9/10
ITB18-028
12. When the entire reprogramming process is complete, the screen in Figure 8 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 8) and attach it to the repair order for warranty documentation.
15. Select Confirm.
Step
13
Step
14
Step
15
Figure 8
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
Reprogram Engine Control Module
(1)
DE97AA
HD
DIA
32
FRT
(2) (3)
(1) Refer to the electronic parts catalog (FAST or equivalent) and use the ECM assembly part number (23703*****) as the Primary Failed Part (PFP).
(2) Reference the current Infiniti Warranty Flat Rate Manual and use the indicated FRT.
(3) FRT allows adequate time to access DTC codes and reprogram ECM. No other diagnostic procedures
subsequently required. Do NOT claim any Diagnostic Op Codes with this claim.
10/10
ITB18-028