NTB17-060b

Classification:
Reference:
EC16-032b
Date:
NTB17-060b
September 13, 2018
2016-2018 TITAN XD; DTC P207F AND DEF SYSTEM ERROR IS
DISPLAYED ON THE VEHICLE INFORMATION DISPLAY
This bulletin has been amended. The Applied Vehicles section, Table A on page 7, and the DTC
Confirmation procedure have been revised. No other changes have been made.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
APPLIED VIN:
APPLIED DATE:
APPLIED ENGINE:
2016-2018 Titan XD (A61)
2016-2017 vehicles: All
2018 vehicles: Built before 1N6BA1(***)JN 529982
Vehicles built before April 12, 2018
Cummins 5.0L V8 Diesel
IF YOU CONFIRM
DTC P207F DEF QLTY SENS is stored,
NOTE: DEF System Error message may be displayed in the
Vehicle Information Display,
DEF System Error
See Dealer
AND
DEF concentration is 32.5% ± 1.5% as indicated by refractometer J-54466.
NOTE: If DEF concentration is incorrect, this bulletin does not apply. Drain DEF tank
and fill with new DEF.
ACTION
1. Save Computer Data with CONSULT-III plus (C-III plus).
2. At step 6 of the ECM Reprogramming procedure, confirm this bulletin applies to the
vehicle you are working on (see page 7).
3. If this bulletin applies, continue with ECM Reprogramming procedure.
4. Write Saved Data with CONSULT-III plus.
5. Perform DTC Confirmation procedure.
NOTE: The vehicle will need to sit for 70 minutes with the ignition ON during this
procedure.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/17
SERVICE PROCEDURE
IMPORTANT: Before starting, make sure:


ASIST on the CONSULT PC has been synchronized (updated) to the current date.
All CONSULT-III plus (C-III plus) software updates (if any) have been installed.
Save Computer Data
1. Connect the CONSULT PC to the vehicle.
2. Open / start C-III plus.
3. Turn the ignition ON, with engine OFF (engine not running).
4. Wait for the plus VI to be recognized.

The Serial No. will display when the plus VI is recognized.
5. Select Diagnosis (One System).
Step
5
Step 4:
plus VI is
recognized
Figure A
2/17
NTB17-060b
6. Navigate C-III plus to Engine > Work Support (see Figure B).
7. Select SAVE COMPUTER DATA.
8. Select Start.
Step
6
Step
7
Step
8
Figure B
NOTE:

After selecting Start, a screen message may appear that says:
Latest diagnostic tool update must be used before saving the data,
otherwise there is a risk that the data entry will not work.

If the above message appears, select Continue.
3/17
NTB17-060b
9. Make sure the ignition is ON and the engine is OFF (engine not running).
10. Select Confirm.
Step
10
Figure C
11. Select End.
Step
11
Figure D
4/17
NTB17-060b
ECM Reprogramming
NOTE:

Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed
on the CONSULT PC screen.

If you are not familiar with the reprogramming procedure, click here. This will link you
to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.

For the Titan XD Diesel, the GR8 set to ECM power supply mode can be attached to
either 12 volt battery.
CAUTION:

Connect the GR8 to the 12V battery and set to ECM power supply mode.
If the vehicle battery voltage goes below 12.0V or above 15.5V during
reprogramming, the ECM may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the ECM may be damaged.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the CONSULT PC and the plus VI. If Bluetooth® signal waves
are within range of the CONSULT PC during reprogramming, reprogramming
may be interrupted and the ECM may be damaged.
5/17
NTB17-060b
1. Return to the C-III- plus Home screen (see Figure 1).
2 Confirm the ignition is ON, with engine OFF.
3. Confirm the plus VI is recognized.

The Serial No. will display when the plus VI is recognized.
4. Select Re/programming, Configuration.
Step 3:
plus VI is
recognized
Step
4
Figure 1
5. Follow the on-screen instructions and navigate C-III plus to the screen shown in
Figure 2 on the next page.
6/17
NTB17-060b
6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).
xxxxxxxxxxxxxxxx
Step 6A:
Current ECM P/N
xxxxx
xxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
Figure 2
B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number
column in Table A below.

If there is a match, continue with the reprogramming procedure.

If there is no match, this bulletin does not apply. Close C-III plus and refer to
ASIST for further diagnostic information.
Table A
Model
Current ECM Part Number: 23710-
2016 Titan XD
Cummins Diesel
EZ41C, EZ41D, EZ41E
EZ42A, EZ42B, EZ42C, EZ42D, EZ42E
EZ43A, EZ43B
2017 Titan XD
Cummins Diesel
EZ44D, EZ44E
EZ45A, EZ45B, EZ45C
2018 Titan XD
Cummins Diesel
EZ47C, EZ47D
7/17
NTB17-060b
7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.
NOTE:

In some cases, more than one new P/N for reprogramming is available.
 If more than one new P/N is available, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.

If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for
further diagnosis.
xxxxx-xxxxx
xxxxx-xxxxx
xxxxx-xxxxx
xxxxx xxxxx
xxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxx
Figure 3
8/17
NTB17-060b
8. When the screen in Figure 4 displays, reprogramming is complete.
NOTE: If the screen in Figure 4 does not display (indicating that reprogramming did not
complete), refer to ECM recovery on the next page.
9. Select Next.
Step
9
Figure 4
NOTE:

In the next step (page 11) you will perform DTC erase.

This operation is required before C-III plus will provide the final reprogramming
confirmation report.
9/17
NTB17-060b
ECM Recovery
Do not disconnect the plus VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 5:

Check battery voltage
(12.0 - 15.5 V).

Ignition is ON, engine OFF.

External Bluetooth® devices
are OFF.

All electrical loads are OFF.

Select retry and follow the
on screen instructions.

“Retry” may not go through on
first attempt and can be
selected more than once.
Figure 5
If reprogramming does not complete and the “X” icon displays as shown in
Figure 6:

Check battery voltage
(12.0 - 15.5 V).

CONSULT A/C adapter is
plugged in.

Ignition is ON, engine OFF.

Transmission is in Park.

All C-III plus / VI cables are
securely connected.

All C-III plus updates are
installed.

Select Home, and restart
the reprogram procedure
from the beginning.
Figure 6
10/17
NTB17-060b
10. Follow the on-screen instructions to Erase DTCs.
11. When the entire reprogramming process is complete, the screen in Figure 7 will display.
12. Verify the before and after part numbers are different.
13. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty
documentation.
14. Select Confirm.
xxxxxx
Step
12
xxxxxx
xxxxxxx
xxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxx
Step
13
Step
14
Figure 7
Continue to the next page.
11/17
NTB17-060b
Write Saved Data
1. Return to the C-III- plus Home screen (see Figure 1A).
2 Confirm the ignition is ON, with engine OFF.
3. Confirm the plus VI is recognized.

The Serial No. will display when the plus VI is recognized.
4. Select Diagnosis (One System).
Step
4
Step 3:
plus VI is
recognized
Figure 1A
12/17
NTB17-060b
5. Navigate C-III plus to Engine > Work Support (see Figure 2A).
6. Select WRITE SAVED DATA.
7. Select Start.
Step
5
Step
6
Step
7
Figure 2A
8. Make sure the ignition is ON and the engine is OFF (engine not running).
9. Select Confirm.
Step
9
Figure 3A
13/17
NTB17-060b
10. Wait for the procedure to complete.
Figure 4A
11. Select End.
Step
11
Figure 5A
14/17
NTB17-060b
IMPORTANT:
The following DTC Confirmation Procedure must be done to confirm proper operation of the
DEF system sensors. If these sensors are not operating properly, DTC P207F may be
stored again in a short time.
DTC Confirmation Procedure
1. Navigate C-III plus to Engine > Data Monitor and select UREA TANK TEMP (see
Figure 1B) and DEF QUALITY SENSOR TEMP (see Figure 2B).
2. Select Start.
Figure 1B
Step
2
Figure 2B
15/17
NTB17-060b
3. Confirm UREA TANK TEMP and DEF QUALITY SENSOR TEMP are -4°C (25°F) or
more.

If needed, start the engine and let it run until the UREA TANK TEMP and DEF
QUALITY SENSOR TEMP warms to -4°C (25°F) or more.
UREA TANK TEMP and DEF
QUALITY SENSOR TEMP:
-4°C (25°F) or more.
Figure 3B
4. Turn the hazard lights (4 way flashers) ON.
5. Allow the vehicle to sit for 70 minutes with the ignition ON.
NOTE: If preferred, the GR8 (battery charger) can be disconnected from the vehicle and
the vehicle can be started and idled for 70 minutes.
6. Use C-III plus to check for DTC P207F.

If DTC P207F is stored again, refer to the Electronic Service Manual (ESM), section
ENGINE > ENGINE CONTROL SYSTEM, for further diagnosis and repair.

If P207F is not stored, go to the next step (step 7).
7. Close C-III plus.
8. Turn the ignition OFF.
9. Disconnect the plus VI from the vehicle.
16/17
NTB17-060b
10. If not already completed, disconnect the GR8 (battery charger) from the vehicle.
11. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.

If the MIL comes ON, go back to ASIST for further diagnostic information.

Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Save Computer Data and ECM
Reprogram
(1)
DX50AA
ZE
32
0.8*
(1) Refer to the electronic parts catalog (FAST) and use the ECM assembly part number as
the Primary Failed Part (PFP).
* FRT allows adequate time to access DTC codes and reprogram ECM. No other
diagnostic procedures subsequently required. Do NOT claim any Diagnostic Op Codes
with this claim.
17/17
NTB17-060b