LTB01208NAS1

Service Bulletin Details

Public Details for: LTB01208NAS1

The hood interior release lever may be inoperative and not release the hood.


- 2017 -

8/2/2018
LTB01208NAS1 - Hood Release Inoperative | TOPIx
LT B 0 1 2 0 8 N A S 1
TECHNICAL BULLETIN
02 AUG 2018
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians
with the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land
Rover service facility to determine whether this bulletin applies to a specific vehicle.
I N F O R M AT I O N
SECTION:
501-14: Handles, Locks, Latches and Entry Systems
S U B J E C T/ C O N C E R N :
Hood Release Inoperative
AFFECTED VEHICLE RANGE:
MODEL:
Discovery (LR)
MODEL YEAR:
2017
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
VIN:
000004-046517
ASSEMBLY PLANT:
Solihull
1/9
8/2/2018
LTB01208NAS1 - Hood Release Inoperative | TOPIx
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
The hood interior release lever may be inoperative and not release the hood.
CAUSE:
This may be caused by the hood release cable not being the correct length.
ACTION:
Should a customer express this concern, follow the Workshop Procedure below.
PA RTS :
PART NUMBER
LR121817
DESCRIPTION
Hood release cable
QUANTITY
1
TOOLS:
Refer to Workshop Manual for any required special tools.
WARRANT Y:
NOTES:
Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to JLR claims submission
system to obtain the latest repair time.
The JLR Claims Submission System requires the use of causal part numbers. Labor only claims
must show the causal part number with a quantity of zero.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
2/9
8/2/2018
LTB01208NAS1 - Hood Release Inoperative | TOPIx
DESCRIPTION
Hood release cable - Renew
SRO
76.16.89.01
TIME (HOURS)
0.5
CONDITION CODE
42
CAUSAL PART
LR083194
NOTE:
Normal Warranty procedures apply.
WORKSHOP PROCEDURE:
1
Verify hood release operation.
If the hood interior release lever does operate the hood latches and the hood can
be opened, go to Step 5.
If the hood interior release lever does not operate the hood latches and the hood
cannot be opened, go to Step 2.
2
NOTE:
Components shown removed from the vehicle for clarity.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
3/9
8/2/2018
LTB01208NAS1 - Hood Release Inoperative | TOPIx

Remove hood interior release lever from the hood release mechanism.
3
NOTE:
Components shown removed from the vehicle for clarity.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
4/9
8/2/2018
LTB01208NAS1 - Hood Release Inoperative | TOPIx

Release the hood release cable from the hood release mechanism.
4
Use a suitable tool to operate the hood release cable to open the hood latches.
5
Remove the hood left and right latches (see TOPIx Workshop Manual section 501-14: Handles,
Locks, Latches and Entry Systems - Removal and Installation - Hood Latch).
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
5/9
8/2/2018
6
LTB01208NAS1 - Hood Release Inoperative | TOPIx

Release the hood release cable.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
6/9
8/2/2018
7
LTB01208NAS1 - Hood Release Inoperative | TOPIx

Remove the trim.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
7/9
8/2/2018
8
LTB01208NAS1 - Hood Release Inoperative | TOPIx

Release the hood release cable from the retainer.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
8/9
8/2/2018
9
LTB01208NAS1 - Hood Release Inoperative | TOPIx

Remove the hood release cable from the vehicle.
10
Reverse Steps 5-9 to install the new hood release cable.
https://topix.jaguar.jlrext.com/topix/content/document/view?id=918908
9/9


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.