T-SB-0079-18
Service Bulletin Details
Public Details for: T-SB-0079-18
Tsb: pre-delivery service (pds) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing pds: ? Careful inspection for paint chips/scratches and body d
- 2010 -
Models from 2010
2010 TOYOTA PRIUS |
T-SB-0079-18 August 6, 2018 ABS Brake Warning Light On Service Category Brake Section Brake Control/Dynamic Control System Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2010 Prius, Prius PHV WMI(s): JTD Plant Code(s): - Introduction Some 2010 model year Prius and Prius Plug-in Hybrid vehicles may exhibit a condition where the brake, ABS, and/or TRAC warning light(s) are on and/or a Check VSC message displays. Diagnostic Trouble Codes (DTCs) C1391, C1252, C1256, and C1253 may be stored. This condition may be caused by a small internal brake fluid leak inside the brake booster assembly with master cylinder. Follow the Repair Procedure in this bulletin to address this condition. Warranty Information MODEL Prius Prius PHV OP CODE DESCRIPTION TIME OFP BR1802 R & R Brake Booster Assembly With Master Cylinder, R & R Brake Booster Pump Assembly, and Reprogram Skid Control ECU 5.8 47050-47140 47050-47150 47070-47060 BR1804 R & R Brake Booster Assembly With Master Cylinder, and R & R Brake Booster Pump Assembly 5.2 T1 T2 8A 99 47050-47090 47070-47060 APPLICABLE WARRANTY This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin. © 2018 Toyota Motor Sales, USA Page 1 of 4 T-SB-0079-18 August 6, 2018 Page 2 of 4 ABS Brake Warning Light On Parts Information PART NUMBER MODEL Prius Prius PHV PART NAME QTY 04002-33347 or 04002-33447 Brake Booster Assy W/Master Cylinder 1 47070-47060 04006-22147 Pump Assy, Brake Booster 1 47050-47090 04002-33647 Brake Booster Assy W/Master Cylinder 1 47070-47060 04006-22147 Pump Assy, Brake Booster 1 PREVIOUS NEW 47050-47140 or 47050-47150 Required Tools & Equipment REQUIRED EQUIPMENT SUPPLIER PART NUMBER Techstream 2.0* QTY TS2UNIT Techstream Lite ADE TSLITEPDLR01 Techstream Lite (Green Cable) 1 TSLP2DLR01 * Essential SST. NOTE Only ONE of the Techstream units listed above is required. Software version 13.10.019 or later is required. Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. REQUIRED TOOLS & MATERIAL FLUID TYPE QTY Brake Fluid DOT3 Brake Fluid 1 – 6 liters © 2018 Toyota Motor Sales, USA T-SB-0079-18 August 6, 2018 Page 3 of 4 ABS Brake Warning Light On Calibration Information MODEL Prius ENGINE 2ZR-FXE CALIBRATION ID PREVIOUS NEW F152647107 F152647108 F152647109 F152647760 F152647127 F152647128 F152647129 F152647770 F152647340 F152647780 F152647350 F152647790 Repair Procedure 1. Confirm the condition exists. Are the brake, ABS, and/or TRAC warning light(s) on and/or does a Check VSC message display? YES — Continue to step 2. NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual. 2. Using Techstream, check for stored DTCs. Record ANY stored DTCs. Are ANY of the following DTCs stored: C1391, C1256, C1252, or C1253? YES — Continue to step 3. NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual. © 2018 Toyota Motor Sales, USA T-SB-0079-18 August 6, 2018 Page 4 of 4 ABS Brake Warning Light On Repair Procedure (continued) 3. Replace the brake booster assembly with master cylinder and the brake booster pump assembly with NEW parts. Refer to TIS, applicable model and model year Repair Manual: 2010 Prius: Brake – Brake System – “Brake System (Other): Brake Booster: Removal / Installation” 2010 Prius: Brake – Brake System – “Brake System (Other): Brake Booster Pump: Removal / Installation” 2010 Prius PHV: Brake – Brake System – “Brake System (Other): Brake Booster: Removal / Installation” 2010 Prius PHV: Brake – Brake System – “Brake System (Other): Brake Booster Pump: Removal / Installation” NOTE Steps 4 and 5 do NOT apply to the Prius Plug-in Hybrid vehicle. Go to step 6 if the vehicle is a Prius Plug-in Hybrid. 4. Using Techstream, confirm the calibration ID. Refer to the Calibration Information chart on page 3. 5. Update the skid control Engine Control Unit (ECU) to the latest calibration ID. 6. Test-drive the vehicle to confirm the repair. © 2018 Toyota Motor Sales, USA