NTB17-113a

Classification:
EC17-033a
Reference:
Date:
NTB17-113a
September 28, 2018
2017-2018 ROGUE SPORT; WHEN COLD LONG CRANK TIME,
ENGINE TURNS OFF, HESITATION, ROUGH IDLE, OR MISFIRE
This bulletin has been amended. The Title and APPLIED VEHICLES have been revised.
Part numbers have been added to Table A on page 5. No other changes have been made.
Discard all previous versions of this bulletin.
APPLIED VEHICLES: 2017-2018 Rogue Sport (J11)
IF YOU CONFIRM
After the engine has been OFF for more than 2 hours, any of the following occur during
engine start and warm up:

Long engine crank time (with mechanical key only)

Engine turns OFF, requiring a restart

Hesitation on acceleration

Rough Idle

Engine misfire
ACTION
1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the
vehicle you are working on.
2. If this bulletin applies, reprogram the ECM.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/10
SERVICE PROCEDURE
IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

All CONSULT-III plus (C-III plus) plus software updates (if any) have been installed.

The CONSULT PC is connected to the Internet (Wi-Fi or cable).
NOTE:

Most instructions for reprogramming with C-III plus are displayed on the CONSULT
PC screen.

If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.

Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume
Learn (IAVL) conditions:
 Engine coolant temperature: 70 -100°C
(158 - 212°F)
 Battery voltage: More than 12.9V (At idle)
 Transmission: Warmed up
Figure A

After reprogramming is complete, you will be required to perform Idle Air Volume
Learn. The above condition are required for Idle Air Volume Learn to complete.
CAUTION:

Connect the GR8 to the 12V battery and select ECM Power Supply Mode.
If the vehicle battery voltage drops below 12.0V or rises above 15.5V during
reprogramming, the ECM may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the ECM may be damaged.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the CONSULT PC and plus VI. If Bluetooth® signal waves are
within range of the CONSULT PC and plus VI during reprogramming,
reprogramming may be interrupted and the ECM may be damaged.
2/10
NTB17-113a
1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.
2. Start C-III plus.
3. Wait for the plus VI to be recognized.

The serial number will display when the plus VI is recognized.
4. Select Re/programming, Configuration.
Step 3:
plus VI is
recognized
Step
4
Figure 1
5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in
Figure 2 on the next page.
3/10
NTB17-113a
6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).
6A: Current ECM P/N
Figure 2
B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number
column in Table A on the next page.

If there is a match, continue with the reprogramming procedure.

If there is not a match, reprogramming does not apply. Refer to ASIST for
further diagnostic and repair information.
4/10
NTB17-113a
Table A
MODEL
CURRENT ECM PART NUMBER: 23710-
2017 Rogue Sport
6MA0A
6MA1A
6MA2A
6MA3A
6MA4A
6MA5A
6MA6A
6MB0A
6MB1A
6MB2A
6MB3A
6MB6A
6MA0B
6MA1B
6MA2B
6MA3B
6MA4B
6MA5B
6MA7A
6MB0B
6MB1B
6MB2B
6MB3B
6MB7A
2018 Rogue Sport
6MH0A
6MH1A
6MH2A
6MH3A
6MH4A
6MH5A
6MH6A
6MH7A
6MH8A
6MH9A
6ME0A
6ME1A
6MG0A
6MG1A
6MG2A
6MG3A
6MG4A
6MG5A
6MG6A
6MG7A
6MG8A
6MG9A
6MH0B
6MH1B
6MH2B
6MH3B
6MH4B
6MH5B
6MH6B
6MH7B
6MH8B
6MH9B
6ME0B
6ME1B
6MG0B
6MG1B
6MG2B
6MG3B
6MG4B
6MG5B
6MG6B
6MG7B
6MG8B
6MG9B
5/10
6MA0D
6MA1D
6MA2D
6MA3D
6MA4D
6MA5D
6MA8A
6MB0D
6MB1D
6MB2D
6MB3D
6MB8A
6MA2E
6MA3E
6MA4E
6MA5E
6MA9A
6MB0E
6MB1E
6MB2E
6MB3E
6MB9A
6MH2C
6MH3C
6MH4C
6MH5C
6MH6C
6MH7C
6MH8C
6MH9C
NTB17-113a
7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.
NOTE:
 In some cases, more than one new P/N for reprogramming is available.
 If there is more than one new P/N, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.
 If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle.
Figure 3

Before reprogramming will start, you will be required to enter your Username and
Password.
 The CONSULT PC must be connected to the Internet (Wi-Fi or cable).
 If you do not know your Username and Password, contact your service
manager.
Figure 4
6/10
NTB17-113a
8. When the screen in Figure 5 displays, reprogramming is complete.
NOTE: If the screen in Figure 5 does not display (indicating that reprogramming did not
complete), refer to the information on page 8.
9. Disconnect the battery charger from the vehicle.
10. Select Next.
Step
10
Figure 5
NOTE:

In the next steps, starting on page 9, you will perform Throttle Valve Closed Position,
Idle Air Volume Learn, Accelerator Closed Position, and DTC erase.

These operations are required before C-III plus will provide the final reprogramming
confirmation report.
7/10
NTB17-113a
ECM recovery:
Do not disconnect the plus VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 6:

Check battery voltage
(12.0–15.5 V).

Ignition is ON, engine OFF.

External Bluetooth® devices
are OFF.

All electrical loads are OFF.

Select retry and follow the
on screen instructions.

“Retry” may not go through
on first attempt and can be
selected more than once.
Figure 6
If reprogramming does not complete and the “X” icon displays as shown in
Figure 7:

Check battery voltage
(12.0 – 15.5 V).

CONSULT A/C adapter is
plugged in.

Ignition is ON, engine OFF.

Transmission is in Park.

All C-III plus / VI cables are
securely connected.

All C-III plus updates are
installed.

Select Home, and restart
the reprogram procedure
from the beginning.
Figure 7
8/10
NTB17-113a
11. Follow the on-screen instructions to perform the following:

Throttle Valve Closed Position.

Idle Air Volume Learn (IAVL).
NOTE:
 Listed below are common conditions required for IAVL to complete.
 If IAVL does not complete within a few minutes, a condition may be out of range.
 Refer to the appropriate ESM for specific conditions required for the vehicle you
are working on.
o Engine coolant temperature: 70 -100°C (158 - 212°F)
o Battery voltage: More than 12.9V (At idle)
o Selector lever: P or N
o Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
o Steering wheel: Neutral (Straight-ahead position)
o Vehicle speed: Stopped
o Transmission: Warmed up

Accelerator Pedal Close Position Learning

Erase DTCs
Continue to the next page.
9/10
NTB17-113a
12. When the entire reprogramming process is complete, the screen in Figure 8 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 8) and attach it to the repair order for warranty
documentation.
15. Select Confirm.
Step
13
Step
14
Step
15
Figure 8
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
CLAIMS INFORMATION
Submit a Primary Part (PP) type claim using the following claims coding:
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Reprogram ECM
(1)
DE97AA
ZE
32
(2) (3)
(1) Reference FAST and use the ECM part number (23710-*****) as the PFP.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.
(3) FRT allows adequate time to access DTC codes and reprogram ECM. No other
diagnostic procedures subsequently required. Do NOT claim any Diagnostic Op Codes
with this claim.
10/10
NTB17-113a