ITB18-026a
Service Bulletin Details
Public Details for: ITB18-026a
Cvt fluid level quick check gauge this bulletin has been amended. See amendment history on the last page. Please discard previous versions of this bulletin.
- 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 -
Models from 2019
2019 INFINITI QX60 |
Models from 2018
2018 INFINITI QX60 |
Models from 2017
2017 INFINITI QX60 |
Models from 2016
2016 INFINITI QX60 |
Models from 2015
2015 INFINITI QX60 |
Models from 2014
2014 INFINITI QX60 |
Models from 2013
2013 INFINITI JX35 |
Classification: Reference: Date: AT18-006a ITB18-026a November 5, 2018 CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. APPLIED VEHICLES: APPLIED VIN and DATE: 2013 JX35 (L50) 2014-2019 QX60 (L50) 2013 JX35 built AFTER 5N1AL0M(* *)DC 343902 and March 26, 2013 2014-2019 QX60 All SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each retailer has been shipped one of these tools. Additional tools can be obtained from Tech–Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check. TP180561 Figure 1 Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/4 SERVICE PROCEDURE NOTE: Steps 1 through 6 will ensure that CVT fluid is properly distributed throughout the CVT. 1. Park the vehicle on level ground (engine running, parking brake set). 2. Using CONSULT III plus (C-III plus), ensure that the CVT Fluid Temperature is at operating temperature 170°F to 180°F (77°C to 82°C). 3. Shift the transmission into REVERSE for 5 seconds. 4. Shift the transmission into DRIVE for 5 seconds. 5. Shift the transmission into REVERSE for 5 seconds. 6. Shift the transmission into PARK. No gauge 7. Remove the cap. Special tool CVT8 Oil Level Quick Check Gauge (J-51155) can now be used to determine CVT fluid level. Pipe “CAP” Figure 2 The handle on the CVT8 Oil Level Quick Check Gauge has two positions, Red and Blue. Refer to Table A on the next page for the correct position for a given vehicle. Red TP180558 TP180557 Blue 2/4 Figure 3 ITB18-026a 8. With the vehicle in PARK and the engine running, insert the CVT8 Oil Level Quick Check Gauge (J-51155) into the pipe. Make sure to use the correct handle position, refer to Table A. Blue Red TP180559 TP180558 Figure 4 Table A MODEL LEVEL (MM) HANDLE POSITION 2013 JX35 (See Applied VIN and Date on page 1) 11-18 Red 2014 – 2019 QX60 (non Hybrid) 11-18 Red 60 mm 9. Inspect the oil level quick check gauge to determine the CVT oil level in millimeters and compare the reading to the specifications in Table A, above. 10 mm TP180560 Figure 5 3/4 ITB18-026a ADJUST CVT FLUID LEVEL 10. Adjust the fluid level from the bottom of the CVT using the charging pipe according to the procedure in the Electronic Service Manual (ESM). AMENDMENT HISTORY Published DATE REFERENCE DESCRIPTION August 15, 2018 ITB18-026 Original bulletin published. November 5, 2018 ITB18-026a Steps 1 and 2 revised. 4/4 ITB18-026a