H181 UPS13018-3B

Service Bulletin Details

Public Details for: H181 UPS13018-3B

An issue has been identified on certain jaguar vehicles within the listed affected vehicle range where the center main crankshaft pulley/damper bolt may have been manufactured away from specification.


- 2020 - 2019 -

Models from 2020
2020 JAGUAR F-TYPE
Models from 2019
2019 JAGUAR F-PACE
2019 JAGUAR F-TYPE
2019 JAGUAR XJ 
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
H181 UPS13018-3BNAS1
TECHNICAL BULLETIN
21 DEC 2018
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with
the knowledge, tools, and equipment required to do the job properly and safely. It informs these
Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a
Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar
service facility to determine whether this bulletin applies to a specific vehicle.
INFORMATION
SECTION:
303-01
SUBJECT/CONCERN:
Update Prior to Sale: Center Main Crankshaft Pulley Bolt
AFFECTED VEHICLE RANGE:
MODEL:
MODEL YEAR:
VIN:
APPLICABILITY:
F-PACE (X761)
2019
394095-601147
V6 S/C 3.0L Petrol /V8 S/C 5.0L Petrol
F-TYPE (X152)
2019-2020
K62212-K62725
V6 S/C 3.0L Petrol /V8 S/C 5.0L Petrol
XJ Range (X351)
2019
W19686-W20172
V6 S/C 3.0L Petrol
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
1/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
An issue has been identified on certain Jaguar vehicles within the listed Affected Vehicle Range where
the center main crankshaft pulley/damper bolt may have been manufactured away from specification.
ACTION:
Retailers are required to HOLD affected new vehicles that are within your control and refrain from
releasing the vehicles for new vehicle sale pending completion of the Diagnostic/Workshop Procedure
detailed in this Technical Bulletin. Unsold vehicles should have this performed as part of the Pre-Delivery
Inspection (PDI) process but must have it completed prior to vehicle handover to the customer.
This program does not apply to any vehicle already registered and in use, either with the retailer or
customer. Any vehicle already in use may continue to be driven and any repair instructions deemed
necessary will be communicated through a separate bulletin.
PARTS:
NOTE:
Partial quantities of all campaign requirements for AJ811490 were shipped to all USA and Canada
Retailers on December 20, 2018. Parts orders for the remaining balance of all campaign parts have
been placed for all USA and Canada Retailers and will be fulfilled over the next several days.
DESCRIPTION
Bolt(s) - Center main crankshaft
pulley
PART NUMBER/SUNDRY
CODE
AJ811490
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
QUANTITY/VALUE
1
EXPECTED PERCENTAGE
DEMAND
100
2/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
SPECIAL TOOLS:
Refer to TOPIx Workshop Manual/Workshop Procedure for any required special tools.
WARRANTY:
NOTE:
Use the Jaguar Land Rover claims submission system to make sure that a vehicle is affected by this
program prior to undertaking any rework action.
At the time of confirming a booking for vehicle repair, make sure that all open Recall and Service Actions
are identified to make sure the correct parts are available and adequate workshop time is allocated for
repairs to be completed at one visit.
Warranty claims must be submitted quoting the Program Code and the relevant Option Code; this will
result in payment of the stated time. The SRO and parts information is included for information only. The
Option Code(s) that allows for the drive in/drive out allowance may only be claimed if the vehicle is
brought back into the workshop for this action alone to be undertaken.
Repair procedures are under constant review and therefore times/prices are subject to change; those
quoted here must be taken as guidance only. Use TOPIx to obtain the latest repair time.
This program is valid for a limited time only. Warranty claims with a repair date prior to the December 20,
2019, closure date must be submitted or payment within 30 calendar days of completion of the repair.
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
SRO
H181
A
F-PACE - V6 3.0L
S/C Petrol
Crankshaft pulley
bolt(s) - Renew
12.21.89.01
1.5
AJ811490
1
H181
B
F-PACE - V6 3.0L
S/C Petrol
Crankshaft pulley
bolt(s) - Renew
Drive In/drive out
12.21.89.01
10.10.10
1.5
0.2
AJ811490
-
1
-
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
TIME
(HOURS)
PART
NUMBER/SUNDRY
CODE
QUANTITY/VALUE
3/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
PROGRAM
CODE
OPTION
CODE
DESCRIPTION
SRO
TIME
(HOURS)
PART
NUMBER/SUNDRY
CODE
QUANTITY/VALUE
H181
C
F-PACE - V8 5.0L
S/C Petrol
Crankshaft pulley
bolt(s) - Renew
12.21.89.01
1.4
AJ811490
1
H181
D
F-PACE - V8 5.0L
S/C Petrol
Crankshaft pulley
bolt(s) - Renew
Drive In/drive out
12.21.89.01
10.10.10
1.4
0.2
AJ811490
-
1
-
H181
E
XJ - V6 3.0L S/C
Petrol
Crankshaft pulley
bolt(s) - Renew
12.21.89.01
2.1
AJ811490
1
H181
F
XJ - V6 3.0L S/C
Petrol
Crankshaft pulley
bolt(s) - Renew
Drive In/drive out
12.21.89.01
10.10.10
2.1
0.2
AJ811490
-
1
-
H181
G
F-TYPE
Crankshaft pulley
bolt(s) - Renew
12.21.89.01
1.5
AJ811490
1
H181
H
F-TYPE
Crankshaft pulley
bolt(s) - Renew
Drive In/drive out
12.21.89.01
10.10.10
1.5
0.2
AJ811490
-
1
-
Normal Warranty policies and procedures apply.
WORKSHOP PROCEDURE 'A' - F-PACE, XJ ONLY:
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.
NOTES:
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
4/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
Some variation in the illustrations may occur, but the essential information is always correct.
Some components shown removed for clarity.
1
NOTE:
F-PACE only.
Remove the radiator (see TOPIx Workshop Manual section 303-03: Engine Cooling - Radiator).
1 Once all tasks are finished, go to Step 3.
2
NOTE:
XJ only.
Remove the cooling fan and shroud (see TOPIx Workshop Manual section 303-03: Engine
Cooling - Cooling Fan and Shroud).
1 Once all tasks are finished, go to Step 3.
3
NOTE:
Do not discard the 2 outer crankshaft pulley bolt(s).

https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
5/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
Remove and set to the side only the 2 highlighted outer crankshaft pulley bolt(s).
4

Install the special tools 303-1437 and 303-1438 as shown.
5

Using the bolt(s) for special tool 303-1437, install the 2 bolt(s) to the crankshaft pulley.
Torque: 25 Nm
6
CAUTION:
Use care when positioning the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
6/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Use a suitable vehicle stand to support the special tools 303-1437 and 303-1438.
7
CAUTIONS:
The center main crankshaft pulley/damper bolt is left-hand thread.
Do not use air tools to remove the center main crankshaft pulley bolt(s).
NOTE:
Loosen the center main crankshaft pulley bolt(s) by hand progressively.

https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
7/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
Remove the center main crankshaft pulley bolt(s).
If the center main crankshaft pulley bolt(s) breaks during removal, continue to hold
the vehicle.
If the center main crankshaft pulley bolt(s) does not break during removal, go to
Step 8.
8

Remove the 2 bolt(s) from special tool 303-1437.
9
CAUTION:
Use care when removing the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
8/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Remove the vehicle stand and special tools 303-1437 and 303-1438.
10
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.

Remove and discard the center main crankshaft pulley bolt(s).
11
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
9/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Install the new center main crankshaft pulley bolt(s).
12
CAUTION:
Use care when positioning the vehicle stand.

Install the special tools 303-1437 and 303-1438.
1 Using the bolt(s) for special tool 303-1437, install the 2 bolt(s) to the crankshaft pulley.
Torque: 25 Nm
2 Use a vehicle stand to support the special tools 303-1437 and 303-1438.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
10/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
13
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.

Tighten the center main crankshaft pulley bolt(s) in 2 stages. Make sure that the socket is turned
through 270º, not the torque wrench.
Torque:
Stage 1: 200 Nm
Stage 2: 270º
14
CAUTION:
Use care when removing the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
11/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Remove the vehicle stand and special tools 303-1437 and 303-1438.
15
NOTE:
The original M10 bolt(s) can be reused.

Install the 2 original outer crankshaft pulley bolt(s).
1 Clean the original outer crankshaft pulley bolt(s).
2 Apply Loctite 270 to the threads.
Torque: 65 Nm
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
12/25
1/7/2019
16
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
NOTE:
F-PACE only.
Install the radiator (see TOPIx Workshop Manual section 303-03: Engine Cooling - Radiator).
1 Once all tasks are finished, release the vehicle.
17
NOTE:
XJ only.
Install the cooling fan and shroud (see TOPIx Workshop Manual section 303-03: Engine Cooling Cooling Fan and Shroud).
1 Once all tasks are finished, release the vehicle.
WORKSHOP PROCEDURE 'B' - F-TYPE ONLY:
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.
1
Remove the cooling fan and shroud (see TOPIx Workshop Manual section 303-03: Engine
Cooling - Cooling Fan and Shroud).
2
Remove the radiator splash shield (see TOPIx Workshop Manual section 501-02: Front End Body
Panels - Radiator Splash Shield).
NOTE:
Perform Steps 3-15 from underneath the vehicle.
3
NOTE:
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
13/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
Do not discard the 2 outer crankshaft pulley bolt(s).

Remove and set to the side only the 2 highlighted outer crankshaft pulley bolt(s).
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
14/25
1/7/2019
4
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Install the special tools 303-1437 and 303-1438 as shown.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
15/25
1/7/2019
5
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Using the bolt(s) for special tool 303-1437, install the 2 bolt(s) to the crankshaft pulley.
Torque: 25 Nm
6
CAUTION:
Use care when positioning the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
16/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Use a suitable vehicle stand to support the special tools 303-1437 and 303-1438.
7
CAUTIONS:
The center main crankshaft pulley/damper bolt is left-hand thread.
Do not use air tools to remove the center main crankshaft pulley bolt(s).
NOTE:
Loosen the center main crankshaft pulley bolt(s) by hand progressively.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
17/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Remove the from center main crankshaft pulley bolt(s).
If the center main crankshaft pulley bolt(s) breaks during removal, continue to hold
the vehicle.
If the center main crankshaft pulley bolt(s) does not break during removal, go to
Step 8.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
18/25
1/7/2019
8
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Remove the 2 outer crankshaft pulley bolt(s) from special tool 303-1437.
9
CAUTION:
Use care when removing the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
19/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Remove the vehicle stand and special tools 303-1437 and 303-1438.
10
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.

https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
20/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx
Remove and discard the center main crankshaft pulley bolt(s).
11
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.

Install the new center main crankshaft pulley bolt(s).
12
CAUTION:
Use care when positioning the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
21/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Install the special tools 303-1437 and 303-1438.
1 Using the bolt(s) for special tool 303-1437, install the 2 bolt(s) to the crankshaft pulley.
Torque: 25 Nm
2 Use a vehicle stand to support the special tools 303-1437 and 303-1438.
13
CAUTION:
The center main crankshaft pulley/damper bolt is left-hand thread.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
22/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Tighten the center main crankshaft pulley bolt(s) in 2 stages. Make sure that the socket is turned
through 270º, not the torque wrench.
Torque:
Stage 1: 200 Nm
Stage 2: 270º
14
CAUTION:
Use care when removing the vehicle stand.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
23/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Remove the vehicle stand and special tools 303-1437 and 303-1438.
15
NOTE:
The original M10 bolt(s) can be reused.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
24/25
1/7/2019
H181 UPS13018-3bNAS1 - Update Prior to Sale: Center Main Crankshaft Pulley Bolt | TOPIx

Install the original outer crankshaft pulley bolt(s).
1 Clean the original outer crankshaft pulley bolt(s).
2 Apply Loctite 270 to the threads.
Torque: 65 Nm
16
Install the radiator splash shield (see TOPIx Workshop Manual section 501-02: Front End Body
Panels - Radiator Splash Shield).
17
Install the cooling fan and shroud (see TOPIx Workshop Manual section 303-03: Engine Cooling Cooling Fan and Shroud).
1 Once all tasks are finished, release the vehicle.
https://topix.landrover.jlrext.com/topix/content/document/view?id=948967
25/25

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.