TSB190022-020420
Service Bulletin Details
Public Details for: TSB190022-020420
This technical service bulletin describes the verification and resolution of refuse trucks at altitude greater than 1220 m [ 4000 ft ] showing fault codes 2639, 1921, and 1922, which are related to high soot load as caused by an incorrect e
- 9999 -
Models from 9999
9999 CUMMINS L9 |
High Soot Load at Altitude in Refuse Truck Applications Page 1 of 3 Technical Service Bulletin Technical Service Bulletin: Released Date: 18-Feb-2019 TSB190022 High Soot Load at Altitude in Refuse Truck Applications High Soot Load at Altitude in Refuse Truck Applications Warranty Statement The information in this document has no effect on present warranty coverage or repair practices, nor does it authorize TRP or Campaign actions. Contents Product Affected Engine: • L9 CM2350 L116B Application: • Refuse Truck Issue Symptom: • Refuse trucks at altitude greater than 1220 m [ 4000 ft ] showing fault codes 2639, 1921, and 1922, which are related to high soot load. Root Cause: • Incorrect engine control module (ECM) calibration. Verification • Application is refuse truck. • Operating altitude of the vehicle is 1220 m [ 4000 ft ] or higher. • Calibration revision is November 2018 or earlier. https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2019/tsb190022.html 2/21/2019 High Soot Load at Altitude in Refuse Truck Applications Page 2 of 3 Resolution If existing calibration revision is November 2018 or earlier: • Perform the published troubleshooting for the fault code. • Update ECM calibration if warrantable update applies. See Table 1 below. • Recommended to keep a low idle speed of 800 rpm. A new authorized change label, Part Number 5297400, must be ordered and installed on engine. To install authorized change label: • Fill out authorized change labor sticker with new CPL, new ECM base code, distributor or dealer code, and date. Leave campaign number section blank. • Clean area near engine dataplate for authorized change label. • Engine dataplate is located on the valve cover/front gear housing. • Peel backing material from authorized change label and install near engine dataplate. • SRT 99-902 is available for authorize change label installation. Table 1, ECM and DO Calibration Codes Engine Power Rating (HP) 370 380 Existing ECM Calibration Code New ECM Calibration Code Existing DO Calibration Code NEW DO Calibration Code HB80003.2 2 HB80500.0 0 DO94971 DO98753 HB80042.2 1 HB80499.0 0 DO94978 DO98752 HB80324.0 4 HB80494.0 0 DO98348 DO97981 HB80320.0 4 HB80493.0 0 DO98342 DO97980 HB80002.2 2 HB80492.0 0 DO94971 DO97981 HB80035.2 1 HB80491.0 0 DO94978 DO97980 HB80316.0 4 HB80492.0 0 DO98348 DO97981 https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2019/tsb190022.html CPL 4758 2/21/2019 High Soot Load at Altitude in Refuse Truck Applications Page 3 of 3 Table 1, ECM and DO Calibration Codes Engine Power Rating (HP) Existing ECM Calibration Code New ECM Calibration Code Existing DO Calibration Code NEW DO Calibration Code HB80312.0 4 HB80491.0 0 DO98342 DO97980 CPL Document History Date 2019-2-4 Details Module Created Last Modified: 18-Feb-2019 https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2019/tsb190022.html 2/21/2019