TSB1501200620201
Service Bulletin Details
Public Details for: TSB1501200620201
This technical service bulletin describes the verification and resolution of a complaint of engine will not start. When attempting to communicate with insite? Electronic service tool, error 5080 - electronic control module (ecm) rom booted
- 9999 -
INSITE Electronic Service Tool Error 5080 - Electronic Control Module (ECM) ROM B... Page 1 of 4 Technical Service Bulletin Technical Service Bulletin: Released Date: 20-Jun-2019 TSB150120 INSITE Electronic Service Tool Error 5080 - Electronic Control Module (ECM) ROM Booted and in a Password Protected State INSITE Electronic Service Tool Error 5080 Electronic Control Module (ECM) ROM Booted and in a Password Protected State Warranty Statement The information in this document authorizes specific changes to the repair practice for failures covered under product warranty coverages. Contents Issue Complaint of engine will not start. When attempting to communicate with INSITE™ electronic service tool, Error 5080 - Electronic Control Module (ECM) ROM Booted is displayed. Upon completion of recalibration to address the ROM boot issue, the ECM is in a password protected state. Verification Product Affected • ISL G CM2180 • ISX12 G CM2180 EJ • ISB6.7 G CM2180 B118 Connect to the ECM. See corresponding Service Manual. Refer to Procedure 019-031 (/qs3/pubsys2/xml/en/procedures/45/45-019-031-tr-islg.html)in section 19. INSITE™ electronic service tool Error 5080 will be present if the ECM is ROM booted. See Figure 1 below. After the ECM has been recalibrated, the ECM will be in a password protected state. See https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2015/tsb150120.html 6/21/2019 INSITE Electronic Service Tool Error 5080 - Electronic Control Module (ECM) ROM B... Page 2 of 4 Figure 2 below. Figure 1, Error 5080 https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2015/tsb150120.html 6/21/2019 INSITE Electronic Service Tool Error 5080 - Electronic Control Module (ECM) ROM B... Page 3 of 4 Figure 2, ECM In Password Protected State Resolution If the ECM has been ROM booted and is in password protected state after recalibration, replace the ECM. See corresponding Service Manual. Refer to Procedure 019-031 (/qs3/pubsys2/xml/en/procedures/45/45-019-031-tr-islg.html)in section 19. Note : This does not include ROM booted events that occur while updating the ECM calibration. Inspect the engine and driveline mounts for signs of wear, see equipment manufacturer service information. If failed engine or driveline mounts are found, please contact the original equipment manufacturer (OEM). ECM replacement is warrantable only if coverage is available for an ECM failure. Table 1, Associated Procedures Engine Model Procedure Title Procedure Number https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2015/tsb150120.html Bulletin Number 6/21/2019 INSITE Electronic Service Tool Error 5080 - Electronic Control Module (ECM) ROM B... Page 4 of 4 Table 1, Associated Procedures Engine Model Procedure Title Procedure Number Bulletin Number ISX12 G CM2180 EJ Electronic Control Module (ECM) Reference Procedure 019031 4310682 ISL G CM2180 Electronic Control Module (ECM) Reference Procedure 019-031 4021649 Electronic Control Module (ECM) Reference Procedure 019-031 5411104 ISB6.7 G CM2180 B118 Document History Date Details 2015-7-24 Module Created 2019-6-10 added table 1 Last Modified: 20-Jun-2019 https://quickserve.cummins.com/qs3/pubsys2/xml/en/tsb/2015/tsb150120.html 6/21/2019