122-L5D8J-09
Service Bulletin Details
Public Details for: 122-L5D8J-09
Instructions for retrofitting the illuminated door entry guard on any porsche my19 and newer.
- 2019 -
Models from 2019
Installation and Conversion Instructions 911 (992) 7/19 ENU 6807 6 Door Entry Guard, Illuminated ADY/ATX Concern: Retrofitting Model Year: As of 2019 Note: The illuminated door entry guards made of carbon-fiber composite (ADY) or stainless steel (ATX) are installed in the door sill areas. Figure 1 Parts Info: 992.044.820.XX1 1 Carbon/stainless-steel door entry guard with "model designation", set For details of available model designations and carbon-fiber composite or stainless steel versions, see Porsche Electronic Parts Catalog (PET). Tequipment Aug 5, 2019 Page 1 of 5 6 911 (992) 6807 ENU Installation and Conversion Instructions 7/19 Parts List: Figure 2 Materials: Tools: ——— 2x Wire harness ——— —— Cleaning agent (commercially available) ——— —— Wrapping tape/insulating tape WE1119 - Hot-air blower, Leister-Electron/VAG 1416, VAS1978/14A or equivalent Work Procedure: Aug 5, 2019 Page 2 of 5 Information • Some of the repair illustrations show only one side of the vehicle or a similar component. • Naturally, some steps also have to be performed on the opposite side of the vehicle as well. 1 Preparatory work 1.1 Disconnect and connect battery charger. Workshop Manual '2X00IN Battery trickle charging' 1.2 Remove and install inner strips. Workshop Manual '2X00IN Removing and installing inner door sill trim'. 1.3 Remove and install cover for fuse box. Workshop Manual '2X00IN Removing and installing front side-section trim panel'. 1.4 Remove and install door entry guards. Workshop Manual '2X00IN Removing and installing cover strip'. Tequipment Installation and Conversion Instructions 911 (992) 7/19 ENU 6807 6 Information Ensure socket contact is seated securely. 2 Route and plug in wire harness on driver's side 2.1 Fold over carpet on driver's side in the fuse box area. 2.2 Fit ground line - brown cable - of the wiring harness on the ground pin Figure 3 -1- in the driver's footwell at the left. Tightening torque: 6.5 ftlb. (9 Nm). Secure ground line to the wiring harness Figure 3 -2- with adhesive tape/wrapping tape. Figure 3 2.3 Plug power supply line - red cable - at the black connector housing connection point for the door wire harness on the connector side coming from the vehicle into Figure 4 -1-pin 16. Release connector and guide pin into the connector housing until it locks with an audible click. Lock the connector again and connect it. Route cable on the wiring harness Figure 4 -2- down to the vehicle floor and secure it to the wiring harness using suitable adhesive tape/wrapping tape. Do not use tie-wraps! 2.4 Route cables on the wiring harness as far as the door entry guard using adhesive tape/wrapping tape. Figure 4 Tequipment Aug 5, 2019 Page 3 of 5 6 911 (992) 6807 ENU 2.5 7/19 Installation and Conversion Instructions Fit illuminated door entry guard (see Step 1.4). Remove door seal close to the cable routing and route cable over the body flange Figure 5 -1-. Fit door seal and connect connector for illuminated door entry guard to the connector on the wiring harness. 2 3 – Cable for illuminated door entry guard – Door entry guard Information Ensure socket contact is seated securely. 3 Figure 5 Route and plug in wire harness on passenger's side 3.1 Fold over carpet on passenger's side in the fuse box area. 3.2 Fit ground line - brown cable - of the wiring harness on the ground pin Figure 6 -1- in the passenger footwell at the right. Tightening torque: 6.5 ftlb. (9 Nm). Secure ground line to the wiring harness Figure 6 -2- with adhesive tape/wrapping tape. Figure 6 Aug 5, 2019 Page 4 of 5 Tequipment Installation and Conversion Instructions 3.3 Plug power supply line - red cable - at the red connector housing connection point for the door wire harness on the connector side coming from the vehicle into Figure 7 -1-pin 16. Release connector and guide pin into the connector housing until it locks with an audible click. Lock the connector again and connect it. Route cable on the wiring harness Figure 7 -2- down to the vehicle floor and secure it to the wiring harness using suitable adhesive tape/wrapping tape. Do not use tie-wraps! 3.4 Route cables on the wiring harness as far as the door entry guard using adhesive tape/wrapping tape. 911 (992) 7/19 ENU 6807 6 Figure 7 3.5 Fit illuminated door entry guard (see Step 1.4). Remove door seal close to the cable routing and route cable over the body flange Figure 8 -1-. Fit door seal and connect connector for illuminated door entry guard to the connector on the wiring harness. 2 3 4 Concluding work 4.1 Working Time: – Cable for illuminated door entry guard – Door entry guard Figure 8 Complete steps 1.1 to 1.4 in reverse order. 68073200: Installing illuminated door entry guard Includes: Installing electric wire harness, removing and installing cover strips. Labor time: 145 TU Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2019 Porsche Cars North America, Inc. Tequipment Aug 5, 2019 Page 5 of 5