K0P_TI_091219
Service Bulletin Details
Public Details for: K0P_TI_091219
Technical instructions: technical instructions for limited service campaign safety connect system ? Vehicle location inaccurate certain 2013 ? 2019 model year 4runner 2011 ? 2017 model year land cruiser 2013 ? 2017 model year prius 2012 ?
- 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 -
Models from 2019
2019 TOYOTA 4RUNNER |
Models from 2018
2018 TOYOTA 4RUNNER |
Models from 2017
2017 TOYOTA 4RUNNER |
2017 TOYOTA LAND CRUISER |
2017 TOYOTA MIRAI |
2017 TOYOTA PRIUS C |
2017 TOYOTA PRIUS V |
Models from 2016
2016 TOYOTA 4RUNNER |
2016 TOYOTA LAND CRUISER |
2016 TOYOTA MIRAI |
2016 TOYOTA PRIUS C |
2016 TOYOTA PRIUS V |
Models from 2012
2012 TOYOTA LAND CRUISER |
2012 TOYOTA PRIUS V |
Models from 2011
2011 TOYOTA LAND CRUISER |
TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN SAFETY CONNECT SYSTEM – VEHICLE LOCATION INACCURATE CERTAIN 2013 – 2019 MODEL YEAR 4RUNNER 2011 – 2017 MODEL YEAR LAND CRUISER 2013 – 2017 MODEL YEAR PRIUS 2012 – 2017 MODEL YEAR PRIUS V 2016 – 2017 MODEL YEAR MIRAI The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this LSC are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this LSC repair are required to currently hold at least one of the following certification levels: • • • • Certified Technician (any specialty) Expert Technician (any specialty) Master Technician Master Diagnostic Technician It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this LSC repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times. 1 I. OPERATION FLOW CHART Verify Vehicle Eligibility Check the VIN on the R.O. matches the vehicle. 2. Check the TIS Vehicle Inquiry System. 1. Not Covered No further action required. Covered Install the SPECIAL CUW application. Perform Health Check on Techstream and check the Calibration ID. Not Covered Reinstall the REGULAR CUW application. Return the vehicle to the customer. Covered <13/14VI-DCM> <12DCM> Only 4RUNNER, PRIUS, PRIUS V: Separate the front passenger seat and disconnect the connectors of the front passenger seat. Disconnect “D/C CUT” or ”SHORT PIN”. Connect GR8/DCA, apply wheel blocks and parking brake and move the shift lever to N position. Connect GR8/DCA, apply wheel blocks and parking brake and move the shift lever to N position. Reprogram DCM. Reprogram DCM. Reprogramming succeeded Reprogramming failed Reprogramming failed Remove DCM from the vehicle. Remove DCM from the vehicle. Reprogram DCM again. Reprogram DCM again. Move the shift lever to P position and remove the wheel blocks and GR8/DCA. Reprogramming succeeded Move the shift lever to P position and remove the wheel blocks and GR8/DCA. Perform Verification Health Check. Reinstall the REGULAR CUW application. Campaign completed, return the vehicle to the customer. 2 II. IDENTIFICATION OF AFFECTED VEHICLES NOTE: • Check the TIS Vehicle Inquiry System to confirm the VIN is involved in this LSC and that the campaign has not already been completed prior to dealer shipment or by another dealer. • TMNA warranty will not reimburse dealers for repairs conducted on vehicles that are not affected or were completed by another dealer. III. PREPARATION A. TOOLS & EQUIPMENT • Standard Hand Tools • CUW Maintenance Tool • • Battery Diagnostic Station Techstream 2.0 / TIS Techstream / Techstream Lite (Software 14.1 or Higher) B. CABLE No.1 & CABLE No.2 The tools shown below have been provided prior to the launch of the campaign. Those tools are necessary when performing this reprogramming procedure. * CABLE No.1 CABLE No.2 * DO NOT use these tools except for this campaign. IV. BACKGROUND The Data Communication Module (DCM) in the subject vehicles are equipped with software to identify the location of the vehicle using the Global Positioning System (GPS) to support features of the Safety Connect system. Due to incorrect programming in the DCM software, after November 2nd, 2019, the GPS coordinates for this system will be calculated incorrectly. This will cause the system to use incorrect vehicle coordinates if one of the system’s features is activated. 3 V. PROCEDURE OVERVIEW CRITICAL INFORMATION • You will perform the reprogramming after installing a dedicated CUW application (Special CUW (only for DCM)) to a Techstream. By using this dedicated CUW application, the reprogramming time can be shortened. • The reprogramming takes more than 60 minutes to complete, and the vehicle will turn the IG OFF automatically when it has passed about 60 minutes with IG ON while the shift lever is in P position. Therefore, make sure to perform the following works before starting the reprogramming. <> < > 4 VI. SAFETY PRECAUTIONS CRITICAL INFORMATION - READ THOROUGHLY An ECU could be damaged if an error occurs in the communication while reprogramming the ECU. Confirm all work is performed as described in these instructions. STABILIZE THE POWER TO THE TECHSTREAM SIDE a) Be sure to connect the Techstream to an external AC power supply. NOTE: The ECU could be damaged if the battery voltage of the Techstream drops while reprogramming. b) Turn off the screen saver and power saving mode of the Techstream so that the power to the hard disk is kept supplied. NOTE: If the screen saver or power saving mode launches while reprogramming, the communication may be disconnected, resulting in the damage of the ECU. c) DO NOT block the ventilation opening for the cooling fan of the Techstream. NOTE: If the ventilation opening for the cooling fan is blocked with a sheet cover or the like, the Techstream may be heated excessively, causing the operation of the Techstream to stop. Due to the stop of the operation, the communication for reprogramming signals could be stopped, resulting in the damage of the ECU. 5 VII. INSTALLATION OF THE SPECIAL CUW APPLICATION • Please make sure to use the special CUW application when performing the ECU reprogramming. • You cannot exit the special CUW application until you complete the reprogramming. DOWNLOAD THE SPECIAL CUW APPLICATION a) Click the link below to download the Special CUW Application SPECIAL CUW APPLICATION RUN THE INSTALLER SELECT THE SPECIAL CUW APPLICATION a) Select “Special CUW (only for DCM)”. b) Click on the “Next” button to install the special CUW application. COMPLETE INSTALLATION a) Click on the “Finish” button to finish. NOTE: Use the special CUW application after installing it to the personal computer which has Techstream. VIII. VEHICLE PREPERATION VEHICLE PREPERATION a) Record settings of the audio system, air conditioner, front seats position, etc. since the cable of the negative battery terminal is going to be disconnected in a later step. Confirm the following conditions • • • • Vehicle in the IG ON position (engine off). Turn off all electrical accessories (i.e. audio system, etc.) Windshield wiper switch in the OFF position. Headlight switch in the DRL OFF position. CONNECT THE 12V BATTERY TO A POWER SUPPLY (GR8/DCA) a) Connect the GR8/DCA or other type of a power supply (not a battery charger) to the 12V battery. b) Select the Power Supply Mode from the Charge Menu of the GR8/DCA. A power supply MUST be used during reprogramming. ECU damage will occur if the battery voltage is not properly maintained during this re-flash procedure. NOTE: A power supply must be connected directly to the 12V battery terminals and NOT the remote jump posts under the hood (if equipped). 6 IX. CHECK FOR DTC’S CONNECT THE TECHSTREAM TO THE VEHICLE a) Turn the IG OFF. b) Using a Cable No.1 (provided tool), connect the Techstream to the vehicle. NOTE: DO NOT use this tool except for this campaign. Follow the instructions below. Otherwise, the battery voltage will decrease or communication will become disabled, and this may require the replacement of the DCM. • Turn off the screen saver and power saving mode of the PC. • Use the external power supply for the PC. (DO NOT use the PC’s internal battery or vehicle’s battery.) • Ensure that the communication cable connectors are securely connected, the cable is in good condition, and the connection is stable. VERIFY TECHSTREAM SETUP a) Verify that the Techstream meets the following conditions: • The software version 14.1 or higher is loaded. • The Techstream battery is fully charged. If not, connect the Techstream to a 120V source. • The DLCIII cable is in good condition. The Techstream’s battery voltage must also be maintained during the re-flash procedure. If necessary, plug the Techstream into a 120v outlet during this procedure. NOTE: If the Techstream communication with the vehicle fails during the re-flash procedure, the DCM will be damaged. CHECK FOR DTCs a) Using a Techstream, perform a Health Check to check for any Diagnostic Trouble Codes. NOTE: This Campaign covers only the software update to the Telematics System, as detailed in these instructions. It does not cover the diagnosis or replacement of any other systems on the vehicle. 7 X. TELEMATICS SYSTEM CALIBRATION ID CHECK Action to take for Telematics System Reprogramming There are 3 different ways to reprogram the Telematics System based on DCM type. Make sure to follow the instructions of these technical instructions. CHECK CURRENT CALIBRATION a) Locate the Update column for the Telematics System in the Stored Data tab for this vehicle. b) Determine the status of an available update; indicated by a YES or NO. Yes Is there an update available for the Telematics System? No Proceed to the next step. c) Campaign complete. Return the vehicle to the customer. Reinstall the REGULAR CUW application. Reprogram the Telematics System to the NEW CID following the table below. NOTE: Take note of both current and new CID to be able to select correctly. DCM(Telematics System) Calibrations DCM Model Current CID Action 12DCM 00002.40.06.04.01.91 Go to section XI 00003.00.05.01.03.16 00003.00.05.01.03.21 13/14 VI-DCM 00003.00.05.01.13.02 00003.00.05.01.13.03 Go to section XII 00003.00.05.01.13.04 00003.00.05.01.13.06 CID other than above Go to section XVI 8 XI. 12DCM UPDATE CALIBRATION Vehicle preparation before updating the telematics system VEHICLE PREPARATION BEFORE UPDATING THE TELEMATICS SYSTEM a) Turn the IG to the OFF position. Be sure to disconnect each connector after disconnect the negative battery terminal b) This illustration uses 4RUNNER for reference DISCONNECT THE FRONT PASSENGER SEAT CONNECTORS (Only 4RUNNER, PRIUS, PRIUS V) NOTE: • The reprogramming may fail if you perform it without disconnecting the connectors. Please make sure to disconnect the connectors before performing the reprogramming. • Disconnect the cable from the negative battery terminal to disable the SRS system. Refer to the repair manual in detail. • Be sure to disconnect each connector after disconnect the negative battery terminal. (1) Separate the front passenger seat, and then disconnect each connector of the front passenger seat. NOTE: Separate the front passenger seat following the instructions on the repair manual. However, there is no need to take it out. Go on TIS and refer to the repair manual for how to separate the seat Path: SEAT / FRONT SEAT ASSEMBLY / REMOVAL Note: you can copy and paste the path above into the TIS search bar to access the instructions quickly (2) Connect the negative battery terminal and GR8/DCA. c) DISCONNECT “D/C CUT ” OR ”SHORT PIN” NOTE: • The reprogramming may fail if you perform it without disconnecting the “D/C CUT” or “SHORT PIN”. Please make sure to disconnect the “D/C CUT” or “SHORT PIN” before performing the reprogramming. • Refer to Section XIV for the location of “D/C CUT” and “SHORT PIN” of each vehicle model. d) Turn the IG to the ON position (engine off). NOTE: DO NOT start the engine. HINT: Depending on the model, method of IG ON may be different. This illustration uses 4RUNNER for reference 9 UPDATE THE TELEMATICS SYSTEM DCM(Telematics System) Calibrations DCM Model Current CID NEW CID 12DCM 00002.40.06.04.01.91 00002.80.06.04.01.91 Check the CUW application a) Check if the Special CUW (only for DCM)” is downloaded. NOTE: If Special CUW (only for DCM) has not been downloaded, follow the instructions of section VII. b) When Calibration Update Wizard is launched, click on “Next”. c) Select a device tool, and then click on “Next”. d) Confirm that "Current Cal ID" and "New Cal ID" are correct, and then click on “Next”. NOTE: The calibration IDs will be displayed as shown on the left. Please make sure you DO NOT mistake where to check to confirm the IDs. e) Follow the on-screen instructions and turn the IG off, and then click on “Next”. NOTE: After “Next” is clicked, a bar showing the progress is displayed. DO NOT turn the IG on while the bar is shown. 10 Vehicle condition before reprogramming DO NOT start the engine. f) Turn the IG to the ON position (engine off). NOTE: DO NOT depress the brake pedal. HINT: Depending on the model, method of IG ON may be different. g) Move the shift lever to Neutral position. NOTE: • The reprogramming takes more than 60 minutes to complete, and the vehicle will turn the IG OFF automatically when it has passed about 60 minutes with IG ON while the shift lever is in P position. Therefore, make sure to move the shift lever to N position before starting the reprogramming. • The alarm sound will be heard if the door is fully closed with IG ON while the shift lever is in Neutral position, on either of the following conditions: - The key is outside the vehicle - The key battery is low 11 h) Click on “Start”. i) While reprogramming, the screen shown on the below is displayed. NOTE: • As reprogramming completes within approximately 75 minutes, stay near the vehicle and DO NOT allow any third parties to operate the vehicle or Techstream in order to prevent troubles from being occurred. The following phenomena may be observed while reprogramming due to interrupted communication. However, there is no problem. - Vehicle proximity alarming sound. - Blackout navigation screen (black). - Indication of a warning lamp or error message in the meter. • “Now processing” is displayed for about 10 minutes. DO NOT finish reprogramming until the screen changes. If the following window is displayed and the reprogramming has failed, click on "Retry" and then "Cancel" to finish the reprogramming process. Remove the DCM (telematics transceiver) from the vehicle and perform the reprogramming procedure again only to the DCM (telematics transceiver). Refer to Section XIII 12 j) After “Flash Calibration Update Successful” is displayed, move the shift lever to Parking position and turn the IG off and click the “Next” button. NOTE: After “Next” is clicked, a bar showing the progress is displayed. DO NOT turn the IG on while the bar is shown. k) Follow the on-screen instructions and turn the IG on, and then click the “Next” button. NOTE: DO NOT turn the IG on with the brake pedal depressed. Otherwise the engine starts. l) After reprogramming, make sure that the "After update "Current Cal ID" is correct. m) Click the “Finish” button. Click the “Finish” button with the IG on, even though the instruction on the screen says to turn the IG off. After the reprogramming has been completed, refer to Section XV and restore the vehicle. 13 XII. 13/14VI-DCM UPDATE CALIBRATION UPDATE THE TELEMATICS SYSTEM DCM(Telematics System) Calibrations DCM Model 13/14 VI-DCM Current CID NEW CID 00003.00.05.01.03.16 00003.20.05.01.03.16 00003.00.05.01.03.21 00003.20.05.01.03.21 00003.00.05.01.13.02 00003.20.05.01.13.02 00003.00.05.01.13.03 00003.20.05.01.13.03 00003.00.05.01.13.04 00003.20.05.01.13.04 00003.00.05.01.13.06 00003.20.05.01.13.06 Check the CUW application a) Check if the Special CUW (only for DCM)” is downloaded. NOTE: If Special CUW (only for DCM) has not been downloaded, follow the instructions of section VII. b) When Calibration Update Wizard is launched, click on “Next”. c) Select a device tool, and then click on “Next”. d) Confirm that "Current Cal ID" and "New Cal ID" are correct, and then click on “Next”. NOTE: The calibration IDs will be displayed as shown on the left. Please make sure you DO NOT mistake where to check to confirm the IDs. 14 e) Follow the on-screen instructions and turn the IG off, and then click on “Next”. NOTE: After “Next” is clicked, a bar showing the progress is displayed. DO NOT turn the IG on while the bar is shown. Vehicle condition before reprogramming DO NOT start the engine. f) Turn the IG to the ON position (engine off). NOTE: DO NOT depress the brake pedal. g) Move the shift lever to Neutral position. NOTE: • The reprogramming takes more than 60 minutes to complete, and the vehicle will turn the IG OFF automatically when it has passed about 60 minutes with IG ON while the shift lever is in P position. Therefore, make sure to move the shift lever to N position before starting the reprogramming. • The alarm sound will be heard if the door is fully closed with IG ON while the shift lever is in Neutral position, on either of the following conditions: - The key is outside the vehicle - The key battery is low 15 h) Click on “Start”. i) While reprogramming, the screen shown on the below is displayed. NOTE: • As reprogramming completes within approximately 85 minutes, stay near the vehicle and DO NOT allow any third parties to operate the vehicle or Techstream in order to prevent issues from occurring. The following phenomena may be observed while reprogramming due to interrupted communication. However, there is no problem. - Vehicle proximity alarming sound. - Blackout navigation screen (black). - Indication of a warning lamp or error message in the meter. • “Now processing” is displayed for about 10 minutes. DO NOT finish reprogramming until the screen changes. If the following window is displayed and the reprogramming has failed, click on "Retry" and then "Cancel" to finish the reprogramming process. Remove the DCM (telematics transceiver) from the vehicle and perform the reprogramming procedure again only to the DCM (telematics transceiver). Refer to Section XIII 16 j) After “Flash Calibration Update Successful” is displayed, move the shift lever to Parking position and turn the IG off and click the “Next” button. NOTE: After “Next” is clicked, a bar showing the progress is displayed. DO NOT turn the IG on while the bar is shown. k) Follow the on-screen instructions and turn the IG on, and then click the “Next” button. NOTE: DO NOT turn the IG on with the brake pedal depressed. Otherwise the engine starts. l) After reprogramming, make sure that the "After update "Current Cal ID" is correct. m) Click the “Finish” button. Click the “Finish” button with the IG on, even though the instruction on the screen says to turn the IG off. After the reprogramming has been completed, refer to Section XV and restore the vehicle. 17 XIII. IF UPDATE CALIBRATION FAILS If the calibration fails contact your FTS for warranty claim filling instructions REMOVE THE DCM (TELEMATICS TRANSCEIVER) Go on TIS and refer to the repair manual for how to separate the seat Path: CELLULAR COMMUNICATION / DCM(TELEMATICS TRANSCEIVER) / REMOVAL Note: you can copy and paste the path above into the TIS search bar to access the instructions quickly CONNECT THE TECHSTREAM TO THE DCM a) Using a Cable No.1 & No.2 (provided tool), connect the Techstream to the DCM. NOTE: DO NOT use these tools except for this campaign. Follow the instructions below. Otherwise, the battery voltage will decrease or communication will become disabled, and this may require the replacement of the DCM. • Turn off the screen saver and power saving mode of the PC. • Use the external power supply for the PC. (DO NOT use the PC’s internal battery or vehicle’s battery.) • Ensure that the communication cable connectors are securely connected, the cable is in good condition, and the connection is stable. 18 UPDATE THE TELEMATICS SYSTEM a) Perform a Health Check. NOTE: • Only "Telematics" will be shown on the System column. • Some DTCs may be shown but it does not affect the reprogramming. DCM(Telematics System) Calibrations DCM Model Current CID NEW CID 12DCM 00002.40.06.04.01.91 00002.80.06.04.01.91 00003.00.05.01.03.16 00003.20.05.01.03.16 00003.00.05.01.03.21 00003.20.05.01.03.21 00003.00.05.01.13.02 00003.20.05.01.13.02 00003.00.05.01.13.03 00003.20.05.01.13.03 00003.00.05.01.13.04 00003.20.05.01.13.04 00003.00.05.01.13.06 00003.20.05.01.13.06 13/14 VI-DCM b) When Calibration Update Wizard is launched, click on “Next”. c) Select a device tool, and then click on “Next”. d) Confirm that "Current Cal ID" and "New Cal ID" are correct, and then click on “Next”. NOTE: The calibration IDs will be displayed as shown on the left. Please make sure you DO NOT mistake where to check to confirm the IDs. e) Click on “Next”. NOTE: It is NOT necessary to follow the instructions on the screen of Techstream. 19 f) Click on “Start”. NOTE: It is NOT necessary to follow the instructions on the screen of Techstream. g) While reprogramming, the screen shown on the below is displayed. NOTE: As reprogramming completes within approximately 75 minutes (12DCM) or 85 minutes (13/14VI-DCM), stay near the vehicle and DO NOT allow any third parties to operate the vehicle or Techstream in order to prevent issues from occurring. The following phenomena may be observed while reprogramming due to interrupted communication. • “Now processing” is displayed for about 10 minutes. DO NOT finish reprogramming until the screen changes. h) After “Flash Calibration Update Successful” is displayed, click the “Next” button. NOTE: After “Next” is clicked, a bar showing the progress is displayed. i) Click the “Next” button. NOTE: It is NOT necessary to follow the instructions on the screen of Techstream. j) k) After reprogramming, make sure that the "After update "Current Cal ID" is correct. Click the “Finish” button. INSTALL THE DCM (TELEMATICS TRANSCEIVER) Go on TIS and refer to the repair manual for how to separate the seat Path: CELLULAR COMMUNICATION / DCM(TELEMATICS TRANSCEIVER) / INSTALLATION Note: you can copy and paste the path above into the TIS search bar to access the instructions quickly 20 XIV. D/C CUT AND SHORT PIN LOCATION 4RUNNER (GRN28#) LAND CRUISER (URJ200) Before Aug. 2015 Production LAND CRUISER (URJ200) After Aug. 2015 Production PRIUS (ZVW50) PRIUS,PRIUS V (ZVW30,ZVW4#) XV.COMPLETE REPAIR DISCONNECT THE GR8/DCA RESTORE THE VEHICLE (IF YOU REPROGRAM 12DCM) a) Reinstall the “D/C CUT FUSE” or “SHORT PIN”. b) (Only 4RUNNER, PRIUS, PRIUS V). (1) Disconnect cable from negative battery terminal. (2) Connect each connector of the front passenger seat. Refer to repair manual for installation. (3) Connect cable to negative battery terminal. (4) Some systems need to be initialized after the cable is reconnected. Refer to repair manual for initialization. PERFORM VERIFICATION HEALTH CHECK a) Using a Techstream, perform a Health Check. b) Clear DTC’s that may have set during the re-flash procedure. c) Re-run the Health Check to confirm that no DTC’s reappear. THIS VERIFICATION HEALTH CHECK IS NECESSARY to update the results and CID’s to the National database. CONFIRM CID UPDATE a) On the Stored Data tab, confirm the following for the DCM: The Update column lists “No” 21 PRINT CUSTOMER HEALTH CHECK REPORT a) From the Stored Data tab, select the Customer Health Check Report button (TIS will launch when button is pressed). b) c) d) e) Log in to TIS. Input Vehicle Mileage and Repair Order number. Check the “Performed” campaign button for campaign K0P Select the Report button. f) g) h) Confirm Customer Health Check Report information is correct. Print Customer Health Check Report from TIS. Sign and provide to the customer. NOTE: If Service Mode screen is shown on the navigation screen, press OK to cancel service mode. 22 XVI. REINSTALL THE REGULAR CUW 作業 Reinstall Regular CUW after Completion RUN THE INSTALLER SELECT THE REGULAR CUW APPLICATION a) Select “Regular CUW (except for DCM)”. b) Click on the “Next” button to install the regular CUW application. COMPLETE INSTALLATION a) Click on the “Finish” button to finish. NOTE: Use the regular CUW application after installing it to the personal computer which has Techstream. ◄ VERIFY REPAIR QUALITY ► - Confirm the calibration has been updated If the seat was removed, confirm it has been reinstalled correctly If the DCM was removed, confirm it has been reinstalled correctly If you have any questions regarding this update, please contact your regional representative. XVII. APPENDIX A. CAMPAIGN DESIGNATION DECODER B. CAMPAIGN PARTS DISPOSAL As required by Federal Regulations, please make sure all campaign parts (original parts) removed from the vehicle are disposed of in a manner in which they will not be reused, unless requested for parts recovery return. 23