A9119022056248_1
Service Bulletin Details
Public Details for: A9119022056248_1
This bulletin contains a software update for when the laserscanner alignment is unsuccessful.
Models from 2020
2020 AUDI A6 |
2020 AUDI A7 |
2020 AUDI A8 |
2020 AUDI E-TRON |
2020 AUDI Q8 |
Models from 2019
2019 AUDI A6 |
2019 AUDI A7 |
2019 AUDI A8 |
2019 AUDI E-TRON |
2019 AUDI Q8 |
91 Laserscanner alignment is unsuccessful 91 19 02 2056248/1 October 21, 2019. Model(s) Year VIN Range Vehicle-Specific Equipment A6, A7, A8, Q8, and Audi e-tron quattro 2019 – 2020 All With Adaptive Cruise Assist Condition Customer states: No customer concerns, it is found during PDI or any other diagnostic work. Workshop findings: An alignment of the control module for laserscanner, J1122 (address word 00CD) is unsuccessful. One of the following reasons is provided in the ODIS Service with VAS tester for the failure: "Yaw angle out of tolerance." "Adjustment successful, no reason." “The calibration panel could not be found.” Technical Background A possible failure of the calibration routine in the software. Production Solution New software in the control module for laserscanner, J1122 (address word 00CD) addressed the condition. Service SVM Update Instructions 1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions. 2. Update the control module for laserscanner, J1122 (address word 00CD) using the SVM action code as listed in the table below, if necessary: Page 1 of 3 © 2019 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Model A6, A7, A8, Q8, and Audi e-tron quattro Old Software Part Number Old Software Version New Software Part Number New Software Version SVM Code Input (or higher) 0200 4K8907660B 0201 4K8907660C 0205 CDA002 0202 Tip: After the update, a bus sleep cycle is necessary so that all DTCs can be deleted. Warranty Claim Type: 110 up to 48 Months/50,000 Miles. G10 for CPO Covered Vehicles – Verify Owner. If the vehicle is outside any warranty, this Technical Service Bulletin is informational only. Service Number: 9159 Damage Code: 0039 Labor Operations: Software Update 0151 0000 Time stated on the diagnostic protocol (Max 75 TU) Diagnostic Time: GFF No allowance 0 TU Road test prior to the service procedure No allowance 0 TU Road test after the service procedure No allowance 0 TU Claim Comment: As per TSB #2056248/1 All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. Page 2 of 3 © 2019 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Additional Information The following Technical Service Bulletin will be necessary to complete this procedure: TSB 2011732, 00 Software Version Management (SVM), operating instructions. All part and service references provided in this TSB (2056248) are subject to change and/or removal. Always check with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair Manual for fasteners, bolts, nuts, and screws that require replacement during the repair. ©2019 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Page 3 of 3 © 2019 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.